Enable the EQoS i.MX driver in defconfig, also enable the PHYLIB
to facilitate the case that only has FEC enabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
Since we uses the DTS and PHY reset gpio in EQoS driver to do the
reset, remove the duplicated codes from board file.
Signed-off-by: Ye Li <ye.li@nxp.com>
i.MX8MP EVK has two ethernet ports. Add relevant nodes and properties
for EQoS port to the EVK DTS file.
In -u-boot.dtsi, change the u-boot eqos compatible string, add PHY
reset gpio and remove assigned clocks as not supported in CCF.
Signed-off-by: Ye Li <ye.li@nxp.com>
i.MX8MP has two ENET controllers, have to update the function to
enable loading two MAC addresses.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As stated in comment above the code, CRS response can be returned to OS
only for 4-byte PCI_VENDOR_ID config read request. So fix the code.
Fixes: 1d7ad68559 ("arm: a37xx: pci: Handle propagation of CRSSVE bit from PCIe Root Port")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We can only select SPL_SKIP_LOWLEVEL_INIT if SPL is enabled, otherwise
we get a warning about unmet dependencies on platforms that don't use
SPL.
Fixes: cf47a8cf8f ("arm: mvebu: Select SPL_SKIP_LOWLEVEL_INIT on ARMADA_32BIT")
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge which represents Aardvark PCIe Root Port does not have
configurable bars.
So ensure that write operation to bars registers on PCI Bridge is noop and
bars registers always contain zero address which indicates that bars are
unsupported.
After this change U-Boot 'pci bar 0.0.0' command does not show any
allocated bars for PCI Bridge device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: cb056005dc ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus")
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SPL_DRIVERS_MISC in board config header,
select it in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Instead of declaring CONFIG_SYS_MALLOC_SIMPLE dependant on
CONFIG_SPL_BUILD in board config header, select
CONFIG_SPL_SYS_MALLOC_SIMPLE in Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
We are printing board information in checkboard() function, which is
called from the default weak implementation of show_board_info().
Rename checkboard() to show_board_info(). This throws away the weak
implementation of show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we always overwrite ethaddrs with those from EEPROM.
In order to allow user to use a cloned MAC address in U-Boot, change the
code so that it sets ethaddr variables only if they aren't set or are
invalid.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently we overwrite ethaddr and eth1addr only if these variables
don't exist.
Better overwrite them even if the env variable exists, but is invalid -
eth_env_get_enetaddr_by_index() checks for validity.
Refactor the code to use a for cycle.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Handle reset button even if we can't configure modules.
This happens if we fail retrieving reset GPIO with which we can reset
the modules.
(Note that this GPIO is different from reset button GPIO.)
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
We are printing board information in last_stage_init(), but U-Boot has
dedicated function, show_board_info(), for this.
Move code which prints board information (board version, serial number,
module topology, ...) to show_board_info().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reorder the definitions in Turris MOX' board config header, drop the
comment relics from when this file was copied, fix indentation.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the config option CONFIG_I2C_MV to a Kconfig option
CONFIG_SYS_I2C_MV and move the default definition from config header
files into defconfigs.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move config options CONFIG_LAST_STAGE_INIT and
CONFIG_DISPLAY_BOARDINFO_LATE to turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
There are two Linux ioctls which implements tcsendbreak() functionality:
TCSBRK and TCSBRKP
TCSBRK with non-zero parameter implements tcdrain() and with zero parameter
implements tcsendbreak() for duration of 0.25s.
TCSBRKP with zero parameter is same as TCSBRK and with non-zero parameter
implements tcsendbreak() for duration in deciseconds specified by
parameter. TCSBRKP does not have to be provided by older toolchain
versions.
So tcsendbreak() has to either use TCSBRK with zero parameter or TCSBRKP
with any parameter.
Fix code to use TCSBRKP and fallback to TCSBRK with 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The function show_eeprom is missing int i if debug is enabled.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
When compiling U-Boot with ld.lld as the linker, the helloworld EFI app
example fails to link:
LD lib/efi_loader/helloworld_efi.so
ld.lld: error: section: .dynamic is not contiguous with other relro
sections
LLD will always create RELRO program header regardless of target
emulation, whereas BFD may automatically disable it for unsupported
targets. Add -znorelro to disable it explicitly in all cases.
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The 'efidebug boot dump' command should not display the VenMedia() device
path node preceding the device path of the initial ram disk.
By letting efi_dp_from_lo() skip the VenMedia() device path node we can
simplify the coding.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Create the GUID as a global variable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Parameter size is never used in function efi_dp_from_lo(). Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of copying a GUID and then using a pointer to the copy for calling
guidcmp(), just pass the pointer to the orginal GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We are ignoring the alignment communicated via the PE/COFF header.
Starting 5.10 the Linux kernel will loudly complain about it. For more
details look at [1] (in linux kernel).
So add a function that can allocate aligned EFI memory and use it for our
relocated loaded image.
[1] c32ac11da3f83 ("efi/libstub: arm64: Double check image alignment at entry")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Vincent Stehlé <vincent.stehle@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When using a file to store UEFI variables we must make sure that secure
boot related variables are not loaded from this file. With commit
9ef82e2947 ("efi_loader: don't load signature database from file")
this has already been implemented for variables defined in the UEFI
specification. As most Linux distributions use Shim we should do the same
for Shim's MOK database.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
It is useful to see some basic EFI info with the command as it forms part
of the information about a board.
Add a hook for this and show the table address as a start.
While here, fix an invalid cast in setup_efi_info(). Note that this
function is using a data structure defined by Linux so we cannot change
it. Also note that ulong is used since this is the standard in U-Boot
(>6k uses), despite there being quite a bit of the more verbose uintptr_t
(930 uses).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The setup routines are called from zimage but don't really belong in the
zimage header. Add a new EFI header to house these. Add comments so it is
clear what the functions do.
Note that these functions are x86-specific. The zimage business is not
used on other architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present this information is stripped when linking. It is useful to keep
it around. Strip it from the .efi files instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Separate this out slightly from the payload, with a new entry.
We might consider renaming EFI PAYLOAD to EFI LOADER, but that would
require quite a lot of file changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This code should never have been added as it builds a new feature on top
of legacy code. This has already been improved with the dependency on BLK.
Add a dependency on DM_ETH also, to avoid needing to deal with this old
code.
Boards which want EFI_LOADER should migrate to driver model first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Repeatedly receive the packets until the receive buffer is empty.
If the buffer is empty, EFI_SIMPLE_NETWORK_PROTOCOL::Receive()
returns EFI_NOT_READY. We don't need to use the wait_for_event()
every time.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Do not check EFI_SIMPLE_NETWORK_RECEIVE_INTERRUPT in packet
receiving loop. This depends on the implementation and not
related to whether the packet can be received or not.
Whether the received packets are available or not is ensured
by wait_for_packet, and that is already done in the loop.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
According to the UEF specification v2.9, the main purpose of the
EFI_SIMPLE_NETWORK_PROTOCOL::GetStatus() is for checking the link
status via EFI_SIMPLE_NETWORK_MODE::MediaPresent.
So this uses net->get_status() for checking the link status before
running network test.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
mkeficapsule is used to create capsules for UEFI firmware update.
To ease inclusion into U-Boot tools packages of Linux distributions we
should add it to the tools-only_defconfig.
Provide dummy values for CONFIG_AVB_BUF_ADDR, CONFIG_AVB_BUF_SIZE to
satisfy Kconfig.
Suggested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The PPC 440 support has been removed in commit 98f705c9ce
("powerpc: remove 4xx support") already, so this file is
certainly not required anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Complete the Sphinx documentation in include/sysreset.h
Add the include to the generated HTML documentation of the U-Boot API.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For enums documented according to the requirements in chapter
"Structure, union, and enumeration documentation" of
https://www.kernel.org/doc/html/latest/doc-guide/kernel-doc.html
errors occur with Sphinx 2.4.4 which disappear with Sphinx 3.4.3,
e.g.
/builds/u-boot/custodians/u-boot-efi/doc/api/sysreset:6:
./include/sysreset.h:60:Unknown interpreted text role "enum".
Sphinx 3.4.3 is the version used by Debian in the current release.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On iMX8MM with Fast Boot fuse blown, the SIT and A-copy image are
placed at different offset than on iMX8MM with Fast Boot fuse NOT
blown. List both options and both offsets to avoid confusion.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The PERSIST_SECONDARY_BOOT is in GPR10 address 0x30390098, adjust the
text which currently says it is in GPR0 while using the correct address
of GPR10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
