The current DDR write level calibration routine always overwrite
the ralat/walat fields to their maximum value, just save
the existing values at the beginning of the calibration routine
and restore it at the end.
In case the delay is estimated by the user to be more than one cycle the
walat should be configured according to that, this is not
automatically done. From the i.MX6 RM:
The user should read the results of the associated delay-line at
MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the
reasonable delay may be above 1 cycle then the user should indicate it at
MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in
MDMISC[WALAT] field. For example, if the result of the write leveling calibration
is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles
then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total
delay will be 2 and 100/256 parts of a cycle
Probably it would just possible to not overwrite the mdmisc register in
the first place, since this is not present in the write_level_calib() example
in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling
Calibration).
Fixes: d339f16911 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
- According to S400 API, the fuse bank 25 (Testconfig2) is able to
access. Add it into driver's mapping table.
- According to FSB words list, the reserved 48 words are ahead of
the bank 5 and bank 6. Fix the wrong position.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable multiple storages for u-boot env:
MMC or SPI flash or NOWHERE for usb
so u-boot can runtime select the storage flash according to boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The TEE memory should be reserved when TEE is present, so need
to runtime update dram bank and memory information according to
tee present or not.
Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable wdog_ad interrupt being triggered by CMC1 to CM33 to let CM33
know A35 reset and reinitialize rpmsg.
Clear wdog_ad and AD_PERIPH reset interrupt after A35 up, otherwise
M33 will always receive interrupt.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If M33 handshake is successful, TPM and DSI panel MUX setting is
done by M33, no need to set them.
If handshake is failed or M33 is not booted, continue the TPM
and DSI panel MUX setting
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update DDR PHY settings to support LPDDR4 mode only by adjusting
DQ VREF ctrl, ODT and pads drive strength.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Found the lposc fuse loading having impact to cpu idle in kernel.
Without the loading in dual boot mode, kernel will hang after idle
for a while.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the LPAV owner to RTD, and assign LPAV masters and peripherals
to APD. So except the masters and peripherals, other resources
(like DDR, cgc2, pcc5) in LPAV won't be reset during reboot and suspend.
No needs to initialize DDR again after reboot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since latest S400 firmware has supported to read OEM SRK Hash, add
it to the driver's table
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable MU0_B clk by default. When M33 image is loaded by Jlink,
the previous method not enable MU0_B clk and not able to communicate
with M33, so let's enable it by default.
And we not put it under kernel dts, because it conflicts with i.MX8QM
suspend/resume logic which requires large change.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When reset with dual boot mode, the LPAV domain won't power down
due to its master is not assigned to APD. So the NICLPAV keeps the
last setting to use PLL4PFD1. So before SPL initialize the PLL4,
we need to switch NICLPAV to FRO192, otherwise system will hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This workaround is not needed on i.MX8ULP proto-1B EVK as board has
fixed the problem. Because we don't support proto-1A any longer,
remove the PMIC settings.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add i3c controller clock enable/disable function for imx8ulp.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add functions to check if M33 image is booted and handshake with M33
image via MU. A core notifies M33 to start init by FCR F0, then wait
M33 init done signal by checking FSR F0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The COUNTER_FREQUENCY is missed in 8ulp configs, it will cause SPL
and u-boot not set the cntfrq_el0. For u-boot, this is ok, because
ATF has set it. But for SPL, it will lead delay and get_timer
not working.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for i.MX8MP USB PHY, i.MX8MP USB is similar to
the i.MX8MQ, except for clock and power domain design customization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Add clock tables required to bring up DWC3 USB, USB PHY and HSIOMIX domain.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Some printf() have strings that doesn't terminate with end of line
and make the output hard to read.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Re-factor the imx8m[nmpq] rate tables into the common pll1416x clock
driver.
43cdaa1567ad3 ("clk: imx8mm: Move 1443X/1416X PLL clock structure to common place")
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
This is a DM clock driver based off the imx8mm u-boot driver and the linux
kernel driver.
All of the PLLs and clocks are initialized so the subsystems below are
functional and tested.
1) USB host and peripheral
2) ECSPI
3) UART
4) I2C all busses
5) USDHC for eMMC support
6) USB storage
7) GPIO
8) DRAM
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Acked-by: Sean Anderson <seanga2@gmail.com>
The mxs_nand_spl driver can support to read from page unaligned offset,
so don't need to set bl_len to ask spl_load_simple_fit to handle
the page unaligned access.
Actually spl_load_simple_fit has two parts of reading:
spl_simple_fit_read and spl_load_fit_image.
The spl_load_fit_image can handle the page unaligned offset,
but the spl_simple_fit_read can't do it. spl_simple_fit_read requires
the FIT location at page aligned offset.
Hence, remove the nand_get_mtd overwrite function from mxs_nand_spl
to use page unaligned read by driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> #gw_ventana
Introduce pwm_dm_imx_get_parms, dm version of pwm_imx_get_parms.
This function get clock rate using clk dm api
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Get and enable ipg/per pwms clocks using dm api into imx_pwm_of_to_plat
and imx_pwm_probe driver function
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mn board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mm board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Disable SPL exception vector which causes issue to ROM patch execution
when SPL calling ROM API.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.
Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
DM is not used for the SPL and a generic DT is used in the SPL
which requires no fixups. Remove the call in the SPL and move the function
into the U-Boot code.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
