The P3060QDS is a Freescale reference board for the six-core P3060 SOC.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM for RCW
Ethernet:
- Eight Ethernet controllers (4x1G + 4x1G/2.5G)
- Three VSC8641 PHYs on board (2xRGMII + 1xMII)
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports two dUARTs up to 115200 bps for console
RapidIO: Two RapidIO, sRIO1 and sRIO2
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman. Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both. A given SOC will only have
a QE or an Fman, so this is safe.
Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND. There's no way to know by looking at a variable how it's supposed
to be used.
In the future, the code which uploads QE firmware and Fman firmware will
be merged.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020. It was already defined for the
P1010 and P1014.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix parameters order in write_dataflash() function extern declaration in
the header file.
Parameters order, as in function definition, should be:
addr_dest, addr_src, size.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This patch fixes the build breakage for the davinci_sonata board.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sergey Kubushyn <ksi@koi8.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
This patch fixes the build breakage for the davinci_schmoogie board.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sergey Kubushyn <ksi@koi8.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
MACH_TYPE_FARADAY was dropped from mach-types.h. Add it back to
board config file.
Signed-off-by: Yan-Pai Chen <ypchen@faraday-tech.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-mmc:
Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"
mmc: mv_sdhci: Fix host version read for Armada100
As a result of the commit 6833260 the uart16550 driver
is broken for Microblaze big endian systems, because of
the missing 3 byte offset. Other than as described, not
all U-Boot BSP will treat properly the 3 byte offset.
This why prefer to mask out the 3 byte offset in general
and setup correct _REG_SIZE value depending on edianess.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Tested-by: Michal Simek <monstr@monstr.eu>
sdhci_readw does not work for host version read in Armada100 series
SoCs. This patch fix this issue by making a sdhci_readl call to get host
version.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
NDS32 and SANDBOX architecture were sharing the same IH_ARCH number
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Acked-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cleanup the cmd_nvedit.c checkpatch warnings, errors and coding style.
There are 10 wanrings left about the simple_strtoul() function:
WARNING: simple_strtoul is obsolete, use kstrtoul instead
#359: FILE: cmd_nvedit.c:359:
+ load_addr = simple_strtoul(argv[2], NULL, 16);
...
total: 0 errors, 10 warnings, 1043 lines checked
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Extract all extern declarations for default_environment[] out of c files
into the environment.h header.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Extract all extern declarations for console_buffer[] out of c files into
the common.h header.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Though one warning left:
WARNING: do not add new typedefs
#149: FILE: u-boot/include/environment.h:149:
+typedef struct environment_s {
total: 0 errors, 1 warnings, 181 lines checked
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
If uintptr_t can be either an unsigned int or an unsigned long int, it is
tricky to use it in a printf() format string. This changes it to
unsigned long int consistently. This should do the right thing on both
32-bit and 64-bit architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-nios:
nios2: Offer ft_board_setup() capability and call fdt_fixup_ethernet().
board/nios2-generic: Use altera_pio driver and remove board specific driver
gpio: Add driver for Altera's PIO core
nios2: Pseudo implement dcache_status/enable/disable()
* 'master' of /home/wd/git/u-boot/custodians:
api: export LCD device to external apps
font: split font data from video_font.h
tools: logo: split bmp arrays from bmp_logo.h
lcd: add clear and draw bitmap declaration
VIDEO: mx3fb: GCC4.6 fix build warnings
Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
* 'master' of git://git.denx.de/u-boot-video:
api: export LCD device to external apps
font: split font data from video_font.h
tools: logo: split bmp arrays from bmp_logo.h
lcd: add clear and draw bitmap declaration
VIDEO: mx3fb: GCC4.6 fix build warnings
Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
* 'master' of /home/wd/git/u-boot/custodians:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
* 'master' of /home/wd/git/u-boot/custodians:
Fix constness of the fdt void pointer in fdt_getprop_u32_default
Add some missing endian conversions in fdt_support.c
* 'master' of git://git.denx.de/u-boot-fdt:
Fix constness of the fdt void pointer in fdt_getprop_u32_default
Add some missing endian conversions in fdt_support.c
* 'master' of /home/wd/git/u-boot/custodians:
adp-ag101p: add product into MAINTAINERS list
adp-ag101p: Add SoC and board support of ag101p
nds32: fix data section of linker script
dwcddr21mctl: Synopsys DWC DDR2/1 Memory Controller
andes_pcu.h: header file of andes_pcu power control unit
This patch exports LCD info-query and bitmap-rendering functions to
external apps.
This patch is tested on a Seaboard. Because the LCD driver is not yet
upstreamed, the test was done in a local downstream repo.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
While video_font.h is useful even without referencing the font data, it
is not possible to be included multiple times because it defines font
data array right in the header.
This patch splits the font data array into video_font_data.h and so now
video_font.h can be included multiple times. This at least solves the
code duplication in board/mcc200/lcd.c.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The generated header bmp_logo.h is useful even outside common/lcd.c for
the logo dimension. However, the problem is, the generated bmp_logo.h
cannot be included multiple times because bmp_logo_palette[] and
bmp_logo_bitmap[] are defined in the bmp_logo.h.
This patch fixes this by defining these arrays in another header
bmp_logo_data.h and in bmp_logo.h only declaring these arrays.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The functions for clearing and drawing bitmaps on the screen were not
exposed publicly and are made public in this patch in preparation for
implementing the display interface of api_public.h.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds the build support for the
omap5_evm board.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This introduces small OneNAND loader, fitting into 1kB of space (smallest
possible OneNAND RAM size). Some devices equipped with such crappy chips will
use this.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
V2: Introduce spl_onenand_load_image() to load data from OneNAND in SPL
V3: Cleanup, align with nand_spl. Skip whole blocks.
The function fdt_getprop_u32_default doesn't modify the fdt, so it can use a
const void * for its fdt argument.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Enable AR8021 as it used on Freescale boards: P1020RDB-PC, P1021RDB-PC,
P2020RDB-PC, P1020UTM-PC, and P1020MSBG-PC.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to support 1920x01080 resolution, we must increase the alloc
length.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m28evk has one bank of RAM.
Fix the comment.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This enables the second port, aka. the port with the USB connector on the
M28EVK.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This code allows the DDR DRAM size to be detected at runtime. The RAM size is
stored into two scratch registers, from which it is then fetched in U-Boot.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue
wasn't addressed because the interrupts weren't enabled on any ARMv5 core,
therefore the issue wasn't noticed earlier.
In previous implementation, the vectoring code used by i.MX28 CPU when an
exception happened was that of the SPL. With this change, the branch target when
an exception happens can be reconfigured by U-Boot.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This patch adds SPL code for the M28 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
