Commit graph

17 commits

Author SHA1 Message Date
Zhao Qiang
ae42eb035e QE/DeepSleep: add QE deepsleep support for mpc85xx
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-21 10:19:19 -07:00
gaurav rana
e04916a721 SECURE_BOOT : enable esbc_validate command for powerpc and arm platforms.
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.

Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.

Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-03-05 12:04:59 -08:00
Alison Wang
8133574ea4 arm: ls1021x: Add support for initializing CAAM's stream id
There 4 JRs, 4 RTICs and 8 DECOs, and set them the same stream id
for using the same SMMU3 on LS1021A.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:11:05 -08:00
Minghuan Lian
636ef95605 arm/ls102xa: create TLB to map PCIe region
LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins
0x48_00000000. In order to access PCIe device, we must create
TLB to map the 40bit physical address to 32bit virtual address.
This patch will enable MMU after DDR is available and creates MMU
table in DRAM to map all 4G space; then, re-use the reserved space
to map PCIe region. The following the mapping layout.

VA mapping:
    -------  <---- 0GB
   |       |
   |       |
   |-------| <---- 0x24000000
   |///////|  ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000
   |-------| <---- 0x300000000
   |       |
   |-------| <---- 0x34000000
   |///////|  ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000
   |-------| <---- 0x40000000
   |       |
   |-------| <---- 0x80000000 DDR0 space start
   |\\\\\\\|
   |\\\\\\\|  ===> 2GB VA map for 2GB DDR0 Memory space
   |\\\\\\\|
   -------  <---- 4GB DDR0 space end

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:10:31 -08:00
Alison Wang
33d2e46591 ls102xa: fdt: Disable QSPI and DSPI in NOR/NAND/SD boot
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-23 22:29:14 -06:00
York Sun
dda3b610ee arm/ls1021a: Add workaround for DDR erratum A008378
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-01-23 22:29:13 -06:00
Xiubo Li
e87f3b308c ARM: ls102xa: allow all the peripheral access permission as R/W.
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.

For now we configure all the peripheral access permissions as R/W.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:42:12 -08:00
Xiubo Li
1a2826f6e0 ls102xa: changing a few targets' configurations.
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:42:03 -08:00
Alison Wang
8ab967b6c6 arm: ls102xa: Add NAND boot support for LS1021AQDS board
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:40:24 -08:00
Minghuan Lian
da419027af arm: ls102xa: Update PCIe dts node status
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:35:56 -08:00
chenhui zhao
306fa01279 arm: ls102xa: clear EPU registers for deep sleep
After wakeup from deep sleep, Clear EPU registers as early as possible
to prevent from possible issue. It's also safe to clear at normal boot.

Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:35:42 -08:00
Nikhil Badola
3f041f011d drivers: usb: fsl: Define USB configs for LS102XA
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-24 09:27:22 -08:00
Zhao Qiang
93d3320417 qe: add u-qe support to arm board
ls1021 is arm-core and support qe which is u-qe.
add u-qe init for arm board.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
[York Sun: Fix compiling error caused by u_qe_init()]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-19 12:55:45 -08:00
Ruchika Gupta
4ba4a095da ls102x: configs - Add hash command in freescale LS1 platforms
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-10-16 14:17:32 -07:00
York Sun
c7eae7fcb1 board/ls1021aqds: Add DDR4 support
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
2014-09-25 09:12:12 -07:00
Wang Huan
327def5060 video: dcu: Add DCU driver support
This patch is to add DCU driver support. DCU also named
2D-ACE(Two Dimensional Animation and Compositing Engine)
is a system master that fetches graphics stored in internal
or external memory and displays them on a TFT LCD panel.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:35 -07:00
Wang Huan
d60a2099a2 arm: ls102xa: Add Freescale LS102xA SoC support
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.

Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-09-08 10:30:32 -07:00