Commit graph

62 commits

Author SHA1 Message Date
Pankaj Bansal
1a048cd656 driver: net: fsl-mc: Add support of multiple phys for dpmac
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.

i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:45:28 -05:00
Nipun Gupta
a78df40cba u-boot: fixup the iommu-map property of fsl-mc node
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.

Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:55:05 -07:00
Alison Wang
a7943fd4c8 armv8: ls2080ardb: update copyright claim
This patch updates the copyright claim for the issues reported by
legal review.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-07-26 10:59:35 -07:00
Bhaskar Upadhaya
7191d45348 board: Kconfig: Re-Arrangement of PPA firmware and header addresses
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.

Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08 16:43:19 -07:00
Fabio Estevam
53deb24dda board/freescale: Remove invalid fsl email addresses
These fsl email addresses are no longer valid and they do not have a
correspondent nxp.com entry.

Remove all invalid fsl email addresses and mark the boards as orphan.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-05-10 20:38:33 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
York Sun
58932ec68c armv8: ls2088ardb: Add 3DS RDIMM support
Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4
DDR chips. LS2088ARDB needs to be modified to connect all DQS signals.
Some of them are grounded by default for x8 chips. Tested with RDIMM
MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support
RDIMM. Dropped related timing table.

Signed-off-by: York Sun <york.sun@nxp.com>
2018-01-30 09:14:07 -08:00
Priyanka Jain
da28a03ed4 board/ls2081ard: Correct code to get QMAP value in checkboard
QMAP value contains information about QSPI chip-selects. These bits
are used to display information of boot device in checkboard()
function.

QMAP value is stored in most significant 3-bits of 8-bit register
brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using
below logic:
	(brdcfg[0] >> 5) & 0x7

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 12:44:23 -08:00
Priyanka Jain
f436fbfeb1 board/ls2081ardb: Update board related prints
Remove Board Arch print as its value is always constant '1' and does
not contain any important information to display during boot.
Add print to display Board FPGA version.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15 12:44:23 -08:00
Yogesh Gaur
70a131eb5a board/ls2080a, ls1088a: Add check for mc-dpl applied in fdt
Function fdt_fixup_board_enet() performs fdt fixup. Only return
fdt_status_okay() when both MC is applied and DPL is deployed, else
return fdt_status_fail().

This check is added to LS1088A/LS2080A/LS2088A boards.

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-14 13:05:07 -08:00
Priyanka Jain
b5dfd47581 board/ls2080ardb: Update board env based on SoC
As per current implementation, default value of board env is
based on board filename i.e ls2080ardb.

With distro support changes, this env is used to decide upon
kernel dtb which is different for other SoCs (ls2088a, ls2081a)
combination supported with this board.

Add support to modify board env at runtime based on SoC type

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:49:14 -07:00
Udit Agarwal
73fbcdf163 armv8: LS2080ARDB: Add secure boot defconfig for QSPI boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: dropped redundant commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Udit Agarwal
15e7c681e1 LS2080ARDB: QSPI boot: Secure Boot image validation
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Santan Kumar
7794d9ab29 board: ls2080ardb: Add fsl_fdt_fixup_flash
IFC and QSPI are muxed on board. Add fsl_fdt_fixup_flash() to disable
IFC node in dts if QSPI is enabled, or disable QSPI node in dts if
otherwise.

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:32 -07:00
Santan Kumar
263536a693 board:ls2080ardb: Update execution of config_board_mux
Function config_board_mux() reads env variable 'hwconfig' which is
only available after relocation for QSPI boot. Move calling
config_board_mux() to misc_init_r().

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:55:02 -07:00
Santan Kumar
6cc914efd2 board/ls2080ardb: Disable SD-related GPIO programming
Smart voltage translator is removed from LS2080ARDB/LS2088ARDB
RevF boards. It is only used on LS2081ARDB. Programming GPIO
is only required for LS2081ARDB.

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:54:43 -07:00
Simon Glass
6e2941d787 common: freescale: Move arch-specific declarations
The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 12:30:55 -04:00
Bogdan Purcareata
33a8991a87 drivers: net: fsl-mc: Link MC boot to PHY_RESET_R
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.

Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.

Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-06-01 19:55:50 -07:00
Udit Agarwal
7676074ac7 armv8: LS2080A: Adjust memory map for secure boot headers for NOR-boot
This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:59:14 -07:00
Santan Kumar
f5bf23d827 armv8: ls2080ardb, ls2080aqds: Adjust memory map for NOR-boot
This patch adjusts memory map for images on LS2080ARDB and
LS2080AQDS NOR flash as below

Image				Flash Offset
RCW+PBI				0x00000000
Boot firmware (U-Boot)		0x00100000
Boot firmware Environment	0x00300000
PPA firmware			0x00400000
PHY firmware			0x00980000
DPAA2 MC			0x00A00000
DPAA2 DPL			0x00D00000
DPAA2 DPC			0x00E00000
Kernel.itb			0x01000000

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:52:29 -07:00
Priyanka Jain
3049a583f3 armv8: ls2080ardb: Add LS2081ARDB board support
LS2081ARDB board is similar to LS2080ARDB board with few differences
 It hosts LS2081A SoC
 Default boot source is QSPI-boot
 It does not have IFC interface
 RTC and QSPI flash device are different
 It provides QIXIS access via I2C

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:47:08 -07:00
Priyanka Jain
89a168f776 armv8: ls2080ardb: Add QSPI-boot support
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:38:55 -07:00
Priyanka Jain
d1418c15c8 board: freescale: ls2080ardb: Update QIXIS code
Update QIXIS related code to be executed only if CONFIG_FSL_QIXIS
flag is enabled. In case QIXIS code is not enabled, use default
sysclk value as 100MHz per board documentation.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:29:13 -07:00
Priyanka Jain
5193405a16 board: freescale: ls2080ardb: Enable SD interface for RevF board
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:12:26 -07:00
Santan Kumar
99fe76d023 armv8: ls2080ardb: Add phy number for serdes1 protocol 0x4b
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-24 09:02:46 -07:00
Simon Glass
3eace37e50 arm: freescale: Rename initdram() to fsl_initdram()
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-12 13:28:32 -04:00
Simon Glass
088454cde2 board_f: Drop return value from initdram()
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:59:20 -04:00
Simon Glass
52c411805c board_f: Drop board_type parameter from initdram()
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:58:44 -04:00
Santan Kumar
54ad7b5ab8 board: freescale: ls2080a/ls2088a: Enable PPA
Enable PPA on LS2080A, LS2088A boards:
-LS2080ARDB, LS2080AQDS
-LS2088ARDB, LS2088AQDS

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 09:27:58 -07:00
Udit Agarwal
a8c6fd4ec1 armv8: LS2080A: Move sec_init to board_init
Moves sec_init to board_init rather than in misc_init function beacuse
PPA will be initialised in board_init function and for PPA validation
sec_init has to be done prior to PPA init.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 08:58:46 -07:00
York Sun
4961eafc25 armv8: layerscape: Update early MMU for DDR after initialization
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-03-14 08:44:03 -07:00
York Sun
36cc0de0b9 armv8: layerscape: Rewrite memory reservation
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-03-14 08:44:03 -07:00
Tom Rini
88077715d8 NXP: Introduce board/freescale/common/Kconfig and migrate CHAIN_OF_TRUST
Introduce board/freescale/common/Kconfig so that we have a single place
for CONFIG options that are shared between ARM and PowerPC NXP platforms.

Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-24 10:33:59 -05:00
Shengzhou Liu
90101386f1 fsl/board/ddr: optimize board-specific cpo for erratum A-009942
Optimize board-specific cpo for erratum A-009942 on b4860qds,
ls1043aqds, ls1043ardb, ls1046aqds, ls1046ardb, ls2080ardb,
t102xqds, t102xrdb, t1040qds, t104xrdb, t208xqds, t208xrdb,
t4qds, t4rdb boards.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-12-15 11:56:39 -08:00
Priyanka Jain
9ae836cde7 armv8: fsl-layerscape: Add NXP LS2088A SoC support
The QorIQ LS2088A SoC is built on layerscape architecture.

It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:54 -08:00
Alexander Graf
215b1fb9fa ls2080ardb: Reserve DP-DDR RAM
The DP-DDR shouldn't be exposed as conventional memory to an OS, so let's
rather claim it's a reserved region in the EFI memory map

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-17 14:18:55 +01:00
Alexander Graf
b7b8410a8f ls2080: Exit dpaa only right before exiting U-Boot
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.

Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.

So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.

For existing boot scripts, nothing should change with this patch.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
2016-11-17 14:18:55 +01:00
Sriram Dash
a5c289b9bc usb: fsl: Rename fdt_fixup_dr_usb
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
2016-09-27 23:30:27 +02:00
York Sun
b63a950629 armv8: ls2080a: Remove debug server support
Debug server feature has been dropped from roadmap.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-09-14 14:07:19 -07:00
York Sun
e61a7534e3 armv8: Move secure_ram variable out of generic global data
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-15 09:01:43 -07:00
Tom Rini
a10a31ec91 Merge branch 'master' of git://git.denx.de/u-boot-usb
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
2016-06-18 23:46:21 -04:00
Sriram Dash
ef53b8c4ce usb: xhci: fsl: Add workaround for USB erratum A008751
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-13 15:16:46 +02:00
Pratiyush Mohan Srivastava
30677deefd board: ls2080a: Add "mcinitcmd" env for MC & DPL deployment
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10 13:44:58 -07:00
Prabhakar Kushwaha
ddd8a08052 armv8: fsl-layerscape: Organize SoC overview at common location
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc

Also move README.lsch2 and README.lsch3 in same folder.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:50 -07:00
York Sun
931e8751af board: ls2080ardb: qds: Fix compiling issue when FSL_MC_ENET not defined
U-Boot should continue to work without management complex (MC).
Fix compiling errors and warnings.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:48 -07:00
Shengzhou Liu
e04f9d0c2f board/freescale: Update ddr clk_adjust
This patch updates clk_adjust to actual value for boards with
T-series and LS-series SoCs to match the setting of clk_adjust
in latest ddr driver.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:06:57 -07:00
Prabhakar Kushwaha
6f3819fe30 armv8: ls2080a: Update MAINTAINERS file
Update MAINTAINERS file for ls2080aqds and ls2080ardb platforms.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:27:15 -07:00
Shengzhou Liu
aa7a2226b5 armv8/ls2080ardb: Update DDR timing to support more UDIMMs
Optimize DDR timing for good margins to support new Transcend
and Apacer DDR4 UDIMM besides current Micron UDIMM.

Verified 1333MT/s, 1600MT/s, 1866MT/s, 2133MT/s rate with
following UDIMM on LS2080ARDB.
 - Micron UDIMM: MTA18ASF1G72AZ-2G1A1Z
 - Apacer UDIMM: 78.C1GM4.AF10B
 - Transcend UDIMM: TS1GLH72V1H

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17 09:26:59 -07:00