Drop the ad-hoc AHCI binding code, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The board file uses the processor type to determine what dtb file
is set. Unfortunately, if the user wants to manually set this,
it get gets overwritten upon boot. This patch adds a check to
see if the value is already set and only changes it if the value
is empty.
Signed-off-by: Adam Ford <aford173@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
The bulk of these changes are an effort to unify Tegra186 builds with
builds of prior 64-bit Tegra generations. On top of that there are
various improvements that allow data (such as the MAC address and boot
arguments) to be passed through from early firmware to the kernel on
boot.
Called to configure Ethernet PHY interface selection and
configure clock selection in RCC Ethernet clock tree.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Add 2 new checks:
- detect when USB TYPE-C cable is not plugged correctly.
In this case, GND and VBUS pins are connected but not CC1
and CC2 pins.
- detect is an USB Type-C charger supplies more than 3 Amps
which is not compliant with the USB Type-C specification
In these 2 situations, stop the boot process and let red led
blinks forever.
V cc1 | V cc2 | power supply | red led | console message
range (Volts) |range (Volts)| (Amps) | blinks |
--------------|-------------|--------------|---------|-----------------------------------
> 2.15 | < 0.2 | > 3 | for ever| USB TYPE-C charger not compliant with specification
[2.15 - 1.23[ | < 0.2 | 3 | NO | NO
[1.23 - 0.66[ | < 0.2 | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | < 0.2 | 0.5 | 2 times | WARNING 500mA power supply detected
< 0.2 | < 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
> 0.2 | > 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update env_get_location() to be able to save environment into
NOR (SPI_FLASH).
Series-cc: pde, cke, pch, uboot-stm32
Cover-letter:
Add saveenv support for STM32MP1
This series adds saveenv support for STM32MP1 on several boot
devices. STM32MP1 is able to boot on eMMC, sdcard and NOR
(NAND support is not fully supported).
On eMMC and sdcard, environment is saved in EXT4 partition
On NOR, environment is saved in a dedicated partition
On NAND, environment is saved in a UBI volume.
This series:
- enables NAND and NOR support on ev1 board
- enables ENV_IS_IN_SPI_FLASH, ENV_IS_IN_UBI, ENV_IS_IN_EXT4
flags
- fixes get_mtdparts()
- allows to override interface, device and partition for ext4
environment
- updates rule to set ENV_IS_NOWHERE value
- introduce ENV_IS_IN_DEVICE
END
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case of several environment location support, env_get_location
is needed to select the correct location depending of the boot
device .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to :
- select the current device to save the environment file
- select the correct EXT4 boot device instance
and partition to save the environment file.
For EXT4, device is mmc, device instance is 0 for sdcard or 1 for eMMC.
The partition is set to "auto" to select the first partition with
bootable flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch configure the default value for mtdids and mtparts
dynamically according the presence of nor and nand in
the board device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Avenger96 board from Arrow Electronics based on STM32MP157
MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards
family and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.
This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.
This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the ethernet MAC address to the kernel upon boot. This passes both
the local-mac-address property (as passed to U-Boot from cboot) and the
currently set MAC address via the mac-address property. The latter will
only be set if it is different from the address that was already passed
via the local-mac-address property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 build are currently dealt with in very special ways, which is
because Tegra186 is fundamentally different in many respects. It is no
longer necessary to do many of the low-level programming because early
boot firmware will already have taken care of it.
Unfortunately, separating Tegra186 builds from the rest in this way
makes it difficult to share code with prior generations of Tegra. With
all of the low-level programming code behind Kconfig guards, the build
for Tegra186 can again be unified.
As a side-effect, and partial reason for this change, other Tegra SoC
generations can now make use of the code that deals with taking over a
boot from earlier bootloaders. This used to be nvtboot, but has been
replaced by cboot nowadays. Rename the files and functions related to
this to avoid confusion. The implemented protocols are unchanged.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is required for proper operation of the 8-bit data transfers.
This fixes transient errors seen on BeagleBone Black.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The MAC address is located at at the last 64K of SPI Flash, and
it's 6 bytes long. This patch corrects both the length and
starting byte of the MAC address.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit 21af33ed03 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC")
wanted to enable DM_MMC only for U-Boot and not for SPL.
But CONFIG_DM_MMC is defined for SPL build too. Because of this
MMC device was not getting registered for SPL causing MMC/SD
boot breakage.
Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until
CONFIG_SPL_DM_MMC is defined.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Enable the new GEMGXL MGMT driver so that GEM 10/100 Mbps works now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Puma SoMs have a 4 MB SPI NOR flash.
Therefore we can move the environment to the end of the flash
(4 MiB - 16 kiB) in order to not overlap with SPL.
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add a short note about how to boot U-Boot on Nyan-big using tegrarcm.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
