Configure the parent clock of wiz3_pll0_refclk to the internal clock
required for USB3 to be functional and also remove "ti,usb2-only"
property as it now supports USB3 mode. This has properties specific to
u-boot on top of DT present in v5.13 of Linux Kernel.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-12-kishon@ti.com
Add support for probing and configuring Torrent serdes on J7200.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-11-kishon@ti.com
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig) and supports resets for each of the
lanes.
This is an adaptation of the linux driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
Add a Sierra PHY driver with PCIe and USB support.
This driver is a port from the mainline linux driver.
The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.
There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself. Additionally there are
resets for each PHY lane.
The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.
The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required) for each lane
group, and then enable the PHY. Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
One difference with the linux driver is that the PHY is
always reset after it is powered-on. This is because role
switching is not supported in u-boot and the cable
orientation is handled by the PHY reset.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com
AM64 has a single lane SERDES which can be configured to be used
with either PCIe or USB. Define the possilbe values for the SERDES
function in AM64 SoC here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-7-kishon@ti.com
Add defines for refclk driver used to route the refclk out of torrent
SERDES.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-6-kishon@ti.com
Add test to check node name ignoring unit address.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20210721155849.20994-3-kishon@ti.com
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
These device trees are updated to match the versions in Linux 5.13.1.
The tick-timer entry in am335x-bone-common.dtsi is preserved.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
HS400 speed mode is now supported in J7200 SoC[1]. Therefore add
mmc-hs400-1_8v tag in sdhci0 device tree node.
Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
(SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
(SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210525093826.10390-3-a-govindraju@ti.com
Read the strobe select value from the device tree property ti,strobe-sel,
required for HS400 speed mode
Fixes: a20008eabd ("mmc: am654_sdhci: Add Support for configuring PHY in J721e")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210525093826.10390-2-a-govindraju@ti.com
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add kernel_comp_addr_r, kernel_comp_size env variables for zynqmp and
versal to be able to use the compressed kernel Image(.gz,.bz2,.lzma,.lzo)
using booti command.
Signed-off-by: Raju Kumar Pothuraju <raju.kumar-pothuraju@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is default value which had been converted by commit 432e398068
("include/configs: drop default definitions of CONFIG_SYS_PBSIZE"). That's
why also remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
reset and poweroff are called via hooks in psci driver which is going
around sysreset framework that's why enable sysreset drivers and do reset
and poweroff via this framework. Using this flow will allow us to call
SYSTEM_WARM_RESET based on psci 1.1 spec which can be calles with reset -w
command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
The same change was done by commit efa1a62ad2 ("ARM: imx8m: Do not define
do_reset() if sysreset is enabled").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_SYSRESET_CMD_POWEROFF defines do_poweroff() in sysreset-uclass.c
that's why don't define it twice when both CONFIG_SYSRESET_CMD_POWEROFF and
CONFIG_CMD_POWEROFF are enabled. CONFIG_SYSRESET_CMD_POWEROFF depends on
CONFIG_CMD_POWEROFF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for xilinx multirate(MRMAC) ethernet driver.
This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC.
Added support for 4 ports of MRMAC for speeds 10G and 25G.
MCDMA supports upto 16 channels but in this driver we have setup only
one channel which is enough.
Tested 10G and 25G on all 4 ports.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add speed macro's for higher ethernet speeds to be used in u-boot
networking drivers. Added Macros for speeds 14G, 20G, 25G, 40G, 50G,
56G, 100G and 200G inline with linux.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
lpd_lsbus is clock which is used by many IPs like dmas, gems, gpio, sdhcis,
spis, ttcs, uarts, watchdog that's why make sense to also enable access to
change this clock. For this clock you already get the rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board zynqmp-zc1751-xm016-dc2 support only USB2.0.
This patch removes USB3.0 DT configuration for DC2 board.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The system refuses to boot without any environment, so return ENVL_NOWHERE when
there's nowhere to store the environment instead of ENVL_UNKNOWN.
This fixes that the board won't boot from eMMC when CONFIG_ENV_IS_IN_FAT is not
defined, for example. Similar for other combinations.
Fixes: 1025bd098a "xilinx: zynqmp: Add support for saving variables"
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these variables/structure are local and should be static.
Issues are reported by sparse:
drivers/mmc/zynq_sdhci.c:49:11: warning: symbol 'zynqmp_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:50:11: warning: symbol 'zynqmp_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:53:11: warning: symbol 'versal_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:54:11: warning: symbol 'versal_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:546:24: warning: symbol 'arasan_ops' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix these kernel doc warnings:
drivers/mmc/zynq_sdhci.c:181: warning: contents before sections
drivers/mmc/zynq_sdhci.c:236: warning: contents before sections
drivers/mmc/zynq_sdhci.c:291: warning: contents before sections
drivers/mmc/zynq_sdhci.c:297: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sdcardclk_set_phase'
drivers/mmc/zynq_sdhci.c:354: warning: contents before sections
drivers/mmc/zynq_sdhci.c:360: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sampleclk_set_phase'
drivers/mmc/zynq_sdhci.c:467: warning: contents before sections
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Restrict tap_delay value to the allowed size(8bits for itap and 6 bits
for otap) before writing to the tap delay register.
Clear ITAP and OTAP delay bits before updating with the new tap value
for Versal platform.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Allow configuring ITAP and OTAP values with zero to avoid failures in
some cases (one of them is SD boot mode). Legacy, SDR12 modes require
to program the ITAP and OTAP values as zero, whereas for SDR50 and SDR104
modes ITAP value is zero.
In SD boot mode firmware configures the SD ITAP and OTAP values and
in this case u-boot has to re-configure required tap values(including zero)
based on the operating mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
set_phase() functions are not modifying the ret value and returning
the same uninitialized ret, return 0 instead.
Keep the return type as int to return errors when the tapdelay's are
set via xilinx_pm_request() in future.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading
images")' changed the way buffer allocation worked for SPL to a more
flexible method.
For xilinx zynqmp the 1MB buffer is not necessarily enough when dealing
with complex fit images (e.g. containing FPGA/TF-A/OP-TEE/U-Boot
proper), which can easily reach up to 10MB, so increase the default
CONFIG_SYS_SPL_MALLOC_SIZE size to 16MB to cover more advanced
scenarios.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Documentation:
provide Makefile documentation
SMBIOS:
generate BIOS release date based on UEFI version
improve error handling in SMBIOS table generation
UEFI:
correct handling of signed capsule if authentication if off
-----BEGIN PGP SIGNATURE-----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=n6EU
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-10-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc1-3
Documentation:
provide Makefile documentation
SMBIOS:
generate BIOS release date based on UEFI version
improve error handling in SMBIOS table generation
UEFI:
correct handling of signed capsule if authentication if off
Commit b81406db51 ("arm: serial: Add debug UART capability to the
pl01x driver") add supports to use pl01x as a debug UART. However,
due to CONFIG_IS_ENABLED macro requires CONFIG_SPL_* prefix, the
_debug_uart_init() would not choose TYPE_PL011 in SPL build. This
patch fixes the bug by judging CONFIG_DEBUG_UART_PL011 explicitly.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change the path from doc/uefi to doc/develop/uefi.
Fixes: commit d1ceeeff6c ("doc: Move UEFI under develop/")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After the commit c70f44817d ("efi_loader: simplify 'printenv -e'"),
"-all" option is no longer necessary.
Just remove them in the test script.
Fixes: c70f44817d ("efi_loader: simplify 'printenv -e'")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the commit c982874e93 ("efi_loader: refactor
efi_setup_loaded_image()"), setjmp-related definitions were moved to
efi_loaded_image_obj in efi_loader.h. So setjmp.h is no longer
refererenced in efi_api.h.
This also fixes some error when efi_api.h will be included in
mkeficapsule.c.
Fixes: c982874e93 ("efi_loader: refactor efi_setup_loaded_image()")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If capsule authentication is disabled and yet a capsule file is signed,
its signature must be removed from image data to flush.
Otherwise, the firmware will be corrupted after update.
Fixes: 04be98bd6b ("efi: capsule: Add support for uefi capsule
authentication")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
efi_guid_capsule_root_cert_guid is never used.
Just remove it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
SMBIOS tables only support 32bit addresses. If we don't have memory here
handle the error gracefully:
* on x86_64 fail to start U-Boot
* during UEFI booting ignore the missing table
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
