With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add TF-A FIP support for trusted boot on STM32MP15x,
when STM32MP15x_STM32IMAGE is not activated.
With FIP support the SSBL partition is named "fip" and its size is 4MB,
so the ENV partition name in device tree (for SD card or eMMC)
or offset in defconfig (CONFIG_ENV_OFFSET / CONFIG_ENV_OFFSET_REDUND)
need to be modified.
With FIP the TEE MTD partitions are removed because the OP-TEE binray are
included in the FIP containers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default for trusted boot with TF-A, U-Boot (u-boot-nodtb)
is located in FIP container with its device tree and with
the secure monitor (provided by TF-A or OP-TEE).
The FIP file is loaded by TF-A BL2 and each components is
extracted at the final location.
This patch add CONFIG_STM32MP15x_STM32IMAGE to request the
STM32 image generation for SOC STM32MP15x
when FIP container is not used (u-boot.stm32 is loaded by TF-A
as done previously to keep the backward compatibility).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.
So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it. This saves us space in some
tight builds. This also shows a few cases where show_boot_progress was
incorrectly guarded before.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the correct name for STMicroelectronics phys config properties,
replace '_' by '-':
"st,eth_clk_sel" => "st,eth-clk-sel"
"st,eth-ref-clk-sel" => st,eth-clk-sel"
These property name are aligned with the upstreamed Linux kernel binding:
linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
See Linux kernel commit "dt-bindings: net: stmmac: add phys config
properties" merged in v5.1-rc1.
This patch allow to reuse the kernel device tree directly in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
Simplify the code of the function board_check_usb_power
based in CONFIG_ADC and adc_measurement; the function is removed by the
linker when the CONFIG_ADC is not activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All these files are add for support rt-thread art-pi board
- add board/st/stm32h750-art-pi, defconfig, header support for u-boot
for more information about art-pi, please goto:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Remove board_early_init_f() and board_late_init() callbacks for stm32
boards as the corresponding flags (CONFIG_BOARD_LATE_INIT and
CONFIG_BOARD_EARLY_INIT_R) are now disabled.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Check whether user has explicitly defined the mmc device to use
in mmc_get_env_dev() with CONFIG_SYS_MMC_ENV_DEV.
On STMicroelectronics boards the used mmc device for environment is
the instance of boot device provided by the ROM code; the mmc instance
is configured by alias in device tree. The used partition is defined in
device tree with u-boot,mmc-env-partition = "ssbl".
This patch allows to override this selection for the support of customer
boards without alias; for example when SDMMC1 is not used and ENV in
mmc0=SDMMC2, user can force the value: CONFIG_SYS_MMC_ENV_DEV = 0.
On STMicroelectronics boards, the current behavior is kept with
CONFIG_SYS_MMC_ENV_DEV = -1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.
For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit d5d726d3cc ("configs: stm32mp1: only support SD card after
NOR in bootcmd_stm32mp"), the stm32mp1 boards only support SD card after
NOR boot device, so the MTD partitions for nand0 or spi-nand0 are useless
(no need of "UBI" partition in nand0 or spi-nand0).
This patch removes these nand MTD update for nor boot and simplify nand0
and spi-nand0 support (remove the mtd_boot variable).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)
In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.
If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.
To avoid this, the power supply current detection algorithm is updated
as following:
- perform an ADC measurement, if a 3A current is detected, continue the
boot process.
- else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
negotiation is done and perform another ADC measurement.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Check whether user has explicitly defined device and partition where
environment file will be located before using 'auto' i.e. bootable
partition
Voids the need to set such partition as bootable to work with the
'dev:auto' tuple
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Michael Opdenacker <michael.opdenacker@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update kernel load address for FIT examples to avoid relocation:
- Kernel example uses Image.gz with U-Boot gzip decompression
at final kernel location 0x0xC0008000.
- Copro example loads zImage at a correct location (0xC4000000),
to avoid zImage relocation before decompression by kernel code.
An other solution to avoid zImage relocation is to align
the kernel load and entry address with the real location in FIT
(the relocation of zImage is skipped in U-Boot bootm command for
identical address) but it is less flexible because this offset
depends on FIT content:
For example:
## Loading kernel from FIT Image at c2000000 ...
Using 'ev1' configuration
Trying 'kernel' kernel subimage
Description: Linux kernel
Created: 2020-10-22 9:08:32 UTC
Type: Kernel Image
Compression: uncompressed
Data Start: 0xc20000cc
The kernel offset in FIT is 0xCC in FIT and zImage is decompressed at
0xC0008000 by kernel code:
kernel {
description = "Linux kernel";
data = /incbin/("zImage");
type = "kernel";
arch = "arm";
os = "linux";
compression = "none";
load = <0xC20000cc>;
entry = <0xC20000cc>;
hash-1 {
algo = "sha1";
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the update of the MTD partitions in kernel device tree
for serial boot (USB / UART), and the kernel will use the MTD
partitions define in the loaded DTB because U-Boot can't known the
expected flash layout in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use const for the variable nodes in ft_board_setup,
this patch follow fdt_fixup_mtdparts prototype and no more use stack.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the file board/st/stm32mp1/board.c which is not more
compiled since commit 156732cc8939 ("board: stm32mp1: move the
function board_debug_uart_init in spl.c")
Fixes: 4fb46816c7 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in ft_board_setup.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in board_late_init.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in dk2_i2c1_fix.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use CONFIG_IS_ENABLED to prevent ifdef in set_dfu_alt_inf.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in sysconf_init.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in board_check_usb_power.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in g_dnl_board_usb_cable_connected
and in g_dnl_bind_fixup
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in board_key_check
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update management of misc_read, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Fixes: 8b8b3d6b55 ("stm32mp1: board: add environment variable for board id and board rev")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate env config in SPL with CONFIG_SPL_ENV_SUPPORT
and use CONFIG_IS_ENABLED macro to test the activated
CONFIG_$(SPL_)ENV_IS_IN_... in env_get_location.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of CONFIG_ENV_IS_IN_MMC in env_get_location, used for
all mmc device (SD card and eMMC).
The 2 configs CONFIG_ENV_IS_IN_MMC and CONFIG_ENV_IS_IN_EXT4 are
incompatible.
Add the weak function mmc_get_env_dev to select the mmc boot instance.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c
This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
With TEE 3.7.0, the partition teed (OP-TEE pageable
code and data) need to increase up to 512KB in NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch updates the current gpio hog implementation and uses
the new API gpio_hog_probe_all(), activated with CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the debug function board_debug_uart_init in spl.c
as the debug_uart_init() function is called in arch_cpu_init()
only for SPL and remove the board.c file.
For TFABOOT, the UART TX pin configuration is done in TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.
The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move function board_ddr_power_init() in a new file stpmic1 in
board/st/common to avoid duplicated code in each board using
stpmic1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
On DK1/2 board, when a 1.5A power supply is detected, a warning
message is displayed. In this message, "1.5mA" is displayed instead
of "1.5A".
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch avoids infinite loop when I/O compensation failed,
it adds a 1s timeout to detect error.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
It is not allowed to change the user setting of bootdelay, so
remove the check of the boot-source to disable it dynamically
in board_late_init()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For booting Linux in the generic distro mechanism and support of
FDTDIR in extlinux.conf , cmd/pxe.c retrieves the FDT file name
from "fdtfile" environment variable.
Dynamically build this variable with compatible of STMicroelectronics
boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Software workaround for I2C issue on EV1 board,
configure the IRQ line for touchscreen before LCD reset
to fix the used I2C address.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Force boot-led ON and no more rely on default-state.
This patch avoid device-tree modification for U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit commit dd2810851e ("stm32mp1: board: support of
error led on ed1/ev1 board") the attended behavior was no more
respected in case of low power source detection on DK2.
The expected behavior is either the error LED keeps blinking for ever,
or blinks 2 or 3 times and must stay ON.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from
NOR or NAND/SPI-NAND is detected.
This patch avoids to define the save MTD partition name for NOR and NAND
devices and issue with latest kernel: only the needed MTD partitions
are defined.
For boot from NOR
1/ bootloader (TF-A, U-Boot and OP-TE) in NOR
2/ one large UBI partition in NAND
For boot from NAND
1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition
2/ one large UBI partition
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the correct macro to test presence CONFIG_LED:
replace CONFIG_IS_ENABLED(CONFIG_LED) by CONFIG_IS_ENABLED(LED)
Issue see during review unrelated patch
"board: stm32mp1: update management of boot-led"
http://patchwork.ozlabs.org/patch/1264823/
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Display the reference MBxxxx found in OTP49
only for STMicroelectronics boards when CONFIG_CMD_STBOARD
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
# Conflicts:
# board/st/stm32mp1/stm32mp1.c
Update the command stboard to support the updated coding of OTP 59 with
finished good.
The ST product codification have several element
- "Commercial Product Name" (CPN): type of product board (DKX, EVX)
associated to the board ID "MBxxxx"
- "Finished Good" or "Finish Good" (FG):
effective content of the product without chip STM32MP1 (LCD, Wifi, …)
- BOM: cost variant for same FG
(for example, several provider of the same component)
For example
- commercial product = STM32MP157C-EV1
- Finished Good = EVA32MP157A1$AU1
Booth information are written on board and these information is also saved
in OTP59:
bit [31:16] (hex) => Board id, MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
The updated command is:
stboard [-y] <Board> <VarCPN> <Revision> <VarFG> <BOM>
And the displayed STMicroelectronics board identification is:
Board: MB<Board> Var<VarCPN>.<VarFG> Rev.<Revision>-<BOM>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Lock the OTP used for board identification for the ST boards after
programming.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Read the value directly from the OTP and no more of the shadows
to avoid the need of reboot after stboard command to have correct value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update management of misc_write, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change the dfu functions dfu_otp_read and dfu_pmic_read to static,
this patch avoids warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add include for dfu, add prototype for set_dfu_alt_info
and avoid warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update readme:
- list the supported SOC and change family to STM32MP15x
- add warning on OTP write and prerequisite:
check if MAC address is not yet provisioned.
- Use filesize for mmc write command (avoid to write all partition
with ${partsize}). ${filesize} and ${partsize} are set by previous
load command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
