Commit graph

84 commits

Author SHA1 Message Date
Marek Vasut
664258887d phy: rcar: Add R-Car Gen2 PHY driver
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-08-14 11:31:19 +02:00
Marek Vasut
5e50adf667 phy: Fix off-by-one error when parsing DT PHY bindings
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
2018-08-14 11:31:19 +02:00
Jagan Teki
69aa1b234e phy: sun4i-usb: Update PHY#3 rst_mask only for H3_H5
Only H3 and H5 have 4 PHYS so restrict rst_mask only for them
by checking PHY id as 3 and update the proper bits.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:41:49 +05:30
Jagan Teki
52185b094d phy: sun4i-usb: Remove usb_clk_cfg set in probe
usb_clk_cfg is setting CTRL_PHYGATE bit value in probe
which is BIT 0 for sun4i, 6i and 8 for a83t but all
these were handling in phy ops init exit calls.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:41:45 +05:30
Jagan Teki
0bfcb47aa0 phy: sun4i-usb: Call phy_passby even for PHY#0
On newer Allwinner SoC, there is a pair of EHCI/OHCI USB hosts
for OTG host mode. USB PHY passby must be configured for its
corresponding PHY. so we can call for PHY#0. on the other hand
in past usb-phy code the same thing can be restricted for
Lower SoC's, other than H3/H5/A64.

Now there is no need to restrict usb passby since the phy driver
is DT enabled, and the respective phy calls will trigger based
DT information initiated by the drivers.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:41:41 +05:30
Patrice Chotard
a1b2faed7c phy: Be able to get phy from PHY provider
In case of phy are provided from a PHY provider nodes as following:

usbphyc: usb-phy@5a006000 {
	compatible = "st,stm32mp1-usbphyc";
	reg = <0x5a006000 0x1000>;
	clocks = <&rcc_clk USBPHY_K>;
	resets = <&rcc_rst USBPHY_R>;
	#address-cells = <1>;
	#size-cells = <0>;

	usbphyc_port0: usb-phy@0 {
		reg = <0>;
		phy-supply = <&vdd_usb>;
		vdda1v1-supply = <&reg11>;
		vdda1v8-supply = <&reg18>
		#phy-cells = <0>;
	};

	usbphyc_port1: usb-phy@1 {
		reg = <1>;
		phy-supply = <&vdd_usb>;
		vdda1v1-supply = <&reg11>;
		vdda1v8-supply = <&reg18>
		#phy-cells = <1>;
	};
};

and PHY are called as following:

usbh_ehci: usbh-ehci@5800d000 {
	compatible = "generic-ehci";
	reg = <0x5800d000 0x1000>;
	clocks = <&rcc_clk USBH>;
	resets = <&rcc_rst USBH_R>;
	interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
	companion = <&usbh_ohci>;
	phys = <&usbphyc_port0>;
	phy-names = "usb";
	status = "okay";
};

generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-19 16:31:35 -04:00
Tom Rini
809e0e398a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-06-04 08:55:00 -04:00
Álvaro Fernández Rojas
9ca33ebf1c phy: bcm6318-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
25d8380f22 phy: bcm6368-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
5a1ab87f53 phy: bcm6358-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
50d16bcf33 phy: bcm6348-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Jagan Teki
aa29b11b3f phy: sun4i-usb: Add a sunxi specific function for setting squelch-detect
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.

The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
194ccb9a34 phy: sun4i-usb: Add A23 USB PHY config
Allwinner A23 has 2 USB PHY's and 0x04 has phy ctrl offset.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
61bf0ed5db phy: sun4i-usb: Add A33 USB PHY config
Allwinner A33 has 2 USB PHY's and 0x10 has phy ctrl offset.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
bf986d1f60 phy: sun4i-usb: Add A31 PHY config
Allwinner A31 has 3 USB PHY's and rest similar to A10.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
7f90b557c9 phy: sun4i-usb: Add A10/A13/A20 PHY config
Add PHY configs for Allwinner A10/A13/A20 which are SUN4I.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
5f646bf1d7 phy: sun4i-usb: Add A83T USB PHY config
Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
bafe5e3061 phy: sun4i-usb: Add V3S PHY config
V3S has 1 USB PHY, rest are similar to A64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
43519c4da7 phy: sun4i-usb: Add H3/H5 PHY config
H3/H5 has 4 USB PHY, rest are similar to A64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
129c45c728 phy: sun4i-usb: Add id_detect and vbus_detect ops
ID and VBUS detection code require when musb changing
between Host and/or Peripheral modes.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
6768594326 phy: Add Allwinner A64 USB PHY driver
USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.

This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.

Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.

Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Tom Rini
624d2cae34 SPDX: Fixup SPDX tags in a few new files
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-20 09:47:45 -04:00
Patrice Chotard
3b29121678 phy: add support for STM32 usb phy controller
This patch adds phy tranceiver driver for STM32 USB PHY
Controller (usbphyc) that provides dual port High-Speed
phy for OTG (single port) and EHCI/OHCI host controller
(two ports).
One port of the phy is shared between the two USB controllers
through a UTMI+ switch.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-18 13:17:31 +02:00
Marek Behún
ca734a875d phy: marvell: a3700: Fix compatible string for ehci
The DTS file for armada-37xx uses the string "marvell,armada3700-ehci",
but the code searched for "marvell,armada-3700-ehci".

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:01:56 +02:00
Marek Behún
2d7a0f4399 phy: marvell: core: Cosmetic fixes
Move the reg_set* functions into comphy.h as static inline functions.
Change return type of get_*_string to const char *.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
7288182aa6 phy: marvell: a3700: Save/restore selector reg in SGMII init
In SGMII initialization PIN_PIPE_SEL has to be zero when resetting
the PHY. Since comphy_mux already set the selector register to
correct values, we have to store it's value before setting it to 0
and restore it after SGMII init.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
22f418935b phy: marvell: a3700: Use comphy_mux on Armada 37xx.
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.

This is needed for Armada 37xx.

This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
3282a3e75f phy: marvell: a3700: Fix SGMII cfg and stat register addresses
The register addresses on lanes 0 and 1 are switched, first comes 1 and
then 0.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
7586ac2b49 phy: marvell: mux: Support nontrivial node order in selector register
Currently comphy_mux supports only trivial order of nodes in pin
selector register, that is lane N on position N*bitcount.

Add support for nontrivial order, with map stored in device tree
property mux-lane-order.

This is needed for Armada 37xx.

As far as I know, there is no driver for Armada 37xx comphy in the
kernel. When such a driver comes, this will need to be rewritten to
support the device tree bindings from the kernel.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
zachary
7d7f22fbd3 phy: marvell: a3700: revise the USB3 comphy setting during power on
This commit is based on commit d9899826 by
  zachary <zhangzg@marvell.com>
from u-boot-marvell, see
github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/d9899826

- According to design specification, the transmitter should be set to high
  impedence mode during electrical idle. Thus transmitter should detect RX
  at high impedence mode also, and delay is needed to accommodate high
  impedence off latency. Otherwise the USB3 will have detection issue that
  most of the time the USB3 device can not be detected at all, or be
  detected as USB2 device sometimes.
  Modified registers: RD005C302h (R181h) (0051h) Lane Configuration 1
  Bit 6: set to 1 to let Tx detect Rx at HiZ mode
  Bit [3:4]: set to 2 to be delayed by 2 clock cycles
  Bit 0: set to 1 to set transmitter to high impedance mode during idle.
- USB3 De-emphasize level of -3.5dB is mandatory, but USB3 MAC selects 0x2
  (emphasize disabled) in the MAC_PHY_TXDEEMPH [1:0], while it is supposed
  to select 0x1(3.5dB emphasize). Thus need to override what comes from
  the MAC(by setting register 0x1c2 bit2 to 0x1) and to configure the
  overridded values of MAC_PHY_TXDEEMPH [1:0] to 0x1(bit15 of register
  0x181 and bit0 of register 0x180).
- According to USB3 application note, need to update below comphy
  registers:
  Set max speed generation to USB3.0 5Gbps(set RD005C04Ah bit[11:10] to 1)
  Set capacitor value to 0xF(set RF005C224 bit[3:0] to 0xF)

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
de49bd0e73 phy: marvell: a3700: Set USB3 RX wait depending on ref clock
According to specification, CFG_PM_RXDLOZ_WAIT should be set to 0x7
when reference clock is at 25 MHz. The specification (at least the
version I have) does not mentoin the setting for 40 MHz reference
clock, but Marvell's U-Boot sets 0xC in that case.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
8609358261 phy: marvell: a3700: Access USB3 register indirectly on lane 2
When USB3 is on comphy lane 2 on the Armada 37xx, the registers
have to be accessed indirectly via SATA indirect access.

This is the case of the Turris Mox board from CZ.NIC.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
a2745c8803 phy: marvell: a3700: Use reg_set_indirect istead of 2 reg_sets
Create a special function for indirect register setting,
reg_set_indirect, and use it instead of the two calls to reg_set.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
1a9283ace5 phy: marvell: a3700: Use (!ret) instead of (ret == 0)
In U-Boot it is usually written this way.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
52f026e224 phy: marvell: a3700: Use same timeout for all register polling
The timeout is set to PLL_LOCK_TIMEOUT in every call to
comphy_poll_reg. Remove this parameter from the function.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
210f4aae81 phy: marvell: a3700: Don't create functional macro for each register
Currently there is for each register special functional macro, ie:
  LANE_CFG1_ADDR(u)
  GLOB_CLK_SRC_LO_ADDR(u)
  ...
where can be either PCIE or USB3.

Change this to one function PHY_ADDR(unit, addr). The code becomes:
  phy_addr(PCIE, LANE_CFG1)
  phy_addr(PCIE, GLOB_CLK_SRC_LO)
  ...

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
63cfff9fde phy: marvell: a3700: Use reg_set16 instead of phy_write16
The macro phy_write16 is not used by the rest of the code,
phy_read16 is not used at all.
We also change the macro SGMIIPHY_ADDR to a static inline function.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Marek Behún
fae82c8f83 phy: marvell: a3700: Change return type of macro MVEBU_REG
All the calls to reg_set and friends have to cast the first argument
to void __iomem *. Lets change the return type of the MVEBU_REG macro
instead.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Masahiro Yamada
d35812368a regmap: change regmap_init_mem() to take ofnode instead udevice
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.

Change the first argumenet to take a device node.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-07 15:49:51 -04:00
Masahiro Yamada
8c1de5e08b regmap: clean up regmap allocation
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members.  There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".

As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.

Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 15:15:27 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Neil Armstrong
2960e27e38 phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers
The Amlogic Meson GXL and GXM (simple variant) embeds up to 3 USB2 PHYs
and an USB3 PHY. This patch adds drivers for these for the standard generic
PHY interface and supports the power-on/off calls and set the Host mode by
default.
They are based on the excellent work from Martin Blumenstingl merged in linux.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-04-11 17:22:07 +02:00
Álvaro Fernández Rojas
8e948c6ff1 phy: add support for bcm6318 usbh phy
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
f55c1538bf phy: add support for bcm6368 usbh phy
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
190c36b975 phy: add support for bcm6358 usbh phy
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-03-21 23:23:13 +01:00
Álvaro Fernández Rojas
bcb9b502d5 phy: add support for bcm6348 usbh phy
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-03-21 23:23:13 +01:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Patrice Chotard
fb48bc448c sti: fix STMicroelectronics copyright
Uniformize all STMicroelectronics copyrights headers for STi
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00