With support for other clock drivers, the potentially supported CDCE913
device can no longer be probed without specifying its DT node name.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
It has been observed that setting SERDES0 lane mux to USB prevents USB 2.0
operation on USB0. Setting SERDES0 lane mux to non-USB when USB0 is used in
USB 2.0 only mode solves this issue. However, for USB3.0+2.0 operation this
issue is not present.
Implement this workaround by writing 1 to LANE_FUNC_SEL field in
CTRLMMR_SERDES0_CTRL register.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Update detect_enable_hyperflash() to look for "ti,am654-ospi" compatible
to match the upstream DT node.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
am335x internal SRAM is too small to support the addition of
SPI bootmode to the default defconfig. Add a separate spiboot_defconfig
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
On J7200 SoC OSPI and HypeFlash are muxed at HW level and only one of
them can be used at any time. J7200 EVM has both HyperFlash and OSPI
flash on board. There is a user switch (SW3.1) that can be toggled to
select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT
nodes to select OSPI vs HyperFlash
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Extend fastboot_set_reboot_flag arguments with reboot reason so that
it could handle different reboot cases in future.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
There shouldn't be a need to call additional i2c read if above failed
already. Based on comment it should be enough to try to detect legacy
boards which are mentioned in the comment.
Fixes: 2463f6728e ("ti: common: board_detect: Allow DM I2C without CONFIG_DM_I2C_COMPAT")
Fixes: 0bea813d00 ("ARM: omap-common: Add standard access for board description EEPROM")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On J7200 SoC OSPI0 and HypeFlash are muxed at HW level and only one of
them can be used at any time. J7200 EVM has both HyperFlash and OSPI
flash on board. There is a user switch (SW3.1) that can be toggled to
select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT
nodes to select OSPI0 vs HyperFlash
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add board detection support for j7200 common processor board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
j7200-evm has minor differences with j721e-evm based on the IPs
available in the SoC. Introduce separate build targets for j7200-evm
to incorporate the differences.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
The DT nodes on J721E SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the current
and the expected corrected path names so that this logic won't be broken
with newer kernels.
Signed-off-by: Suman Anna <s-anna@ti.com>
Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Current usage of eeprom apis produce a build failure when
CONFIG_TI_I2C_BOARD_DETECT is not defined. Add stub function for these
apis to avoid build failures.
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting from USB mass storage devices
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting in USB peripheral (DFU) bootmode
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The DT nodes on AM65x SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the
current and the expected corrected path names so that this logic won't
be broken with newer kernels.
The logic also corrects the crypto node name as the DT node
unit-addresses are all expected to be lower case.
Signed-off-by: Suman Anna <s-anna@ti.com>
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
At this point in time we can now remove our legacy code and switch to
enabling DM for USB and Ethernet.
Cc: Derald D. Woods <woods.technical@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
The TI814x (DM814x) platform is rather old and in need of a lot of
migration work. As much of that work is well past the deadline, remove
this platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
Both the am335x_boneblack and am335x_evm_usbspl configs have been gone
for a while, remove their entries from MAINTAINERS.
Signed-off-by: Tom Rini <trini@konsulko.com>
On HS devices the access to SA2UL is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.
We used to only disable the TRNG but now that we have full SA2UL
support in Linux, in which TRNG is a sub-module, disable both
by disabling the parent SA2UL node.
Signed-off-by: Andrew F. Davis <afd@ti.com>
With clang we get a report that we are setting this member twice.
Fortunately it is to the same value, so drop the hard-coded value line.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
When building this code with clang-10 a number of warnings will be
generated along the lines of:
warning: address of array 'ep->version' will always evaluate to 'true'
Convert these checks to checking the strlen of the part of the array we
care about. As this array will be null terminated previously by us,
this is safe.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
am57x_idk_lcd_detect() exits immediately if a known board not having
an LCD is found, i.e. a non-IDK board. This is annoying as we have to
remember to add an extra OR clause for every new non-IDK board.
Add a board_is_ti_idk() macro so that the logic becomes positive (detect
LCD on IDK boards instead of not-known-without-LCD boards). Even more
important, add the macro just below the board_is_*_idk() macros, so it is
easy to remember to update it when adding a new IDK.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Enable DM_ETH on omap3_logic board
- Enable Caches in SPL for K3 platforms
- Enable backup boot mode support for J721E
- Update the DDR timings for AM654 EVM
- Add automated tests for RX-51
Add support for enabling dcache already in SPL. It accelerates the boot
and resolves the risk to run into unaligned 64-bit accesses.
Based on original patch by Lokesh Vulta.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
The OP-TEE binary to use is renamed to v2 as the v1 binary has been
deprecated and is no longer built by default.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Now k3-image-gen[0] is the official repository for generating sysfw.itb
Update the same in AM65x and J721e README.
[0] https://git.ti.com/cgit/k3-image-gen/k3-image-gen/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Initialize both ESM and ESM_PMIC support if available for the board.
If support is not available for either, a warning is printed out.
ESM signals are only properly routed on PM2 version of the J721E SOM,
so only probe the drivers on this device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
On am571x-idk there can be following configurations based on Jumper J51
and LCD panel detected.
1) J51 removed (6port): 6 port Ethernet. Disable LCD panel.
2) J51 placed (LCD) + Panel detected: 4 port Ethernet with appropriate LCD.
3) J51 placed (LCD) + Panel not detected/not supported.
Configuration 3 is considered invalid as we can't use display nor ICSS1
ethernet ports due to hardware muxing. Alert the user to fix the
configuration and prevent boot.
Alternative was to allow boot and limit to 4 port Ethernet with no display
but this involved introduction of another DTB for the kernel and was
considered not worth the hassle.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Not finding a node that we try to disable does not always need to be
fatal to boot but should at least print out a warning. Return error
from fdt_disable_node as it did fail to disable the node, but only
warn in the case of disabling the TRNG as this will not prevent boot.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The TI J721E EVM system on module (SOM), the common processor board, and
the associated daughtercards have on-board I2C-based EEPROMs containing
board config data. Use the board detection infrastructure to do the
following:
1) Parse the J721E SOM EEPROM and populate items like board name, board
HW and SW revision as well as board serial number into the TI common
EEPROM data structure residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing associated I2C
addresses used for on-board EEPROMs containing daughter card-specific
data. If such a card is found, parse the EEPROM data such as for
additional Ethernet MAC addresses and populate those into U-Boot
accordingly
3) Dynamically apply daughter card DTB overlays to the U-Boot (proper)
DTB during SPL execution
4) Dynamically create an U-Boot ENV variable called name_overlays
during U-Boot execution containing a list of daugherboard-specific
DTB overlays based on daughercards found to be used during Kernel
boot.
This patch adds support for the J721E system on module boards containing
the actual SoC ("J721EX-PM2-SOM", accessed via CONFIG_EEPROM_CHIP_ADDRESS),
the common processor board ("J7X-BASE-CPB"), the Quad-Port Ethernet
Expansion Board ("J7X-VSC8514-ETH"), the infotainment board
("J7X-INFOTAN-EXP") as well as for the gateway/Ethernet switch/industrial
expansion board ("J7X-GESI-EXP").
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use dm_i2c_probe() rather than i2c_get_chip() when trying to access
board-detection EEPROM devices. This has the advantage of more gracefully
handling the case when the EEPROM is not present by allowing to exit the
function early rather than failing and outputting an error message on the
I2C transactions that follow.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
These are necessities for beaglebone ai boot. There is the addition of
CONFIG_SUPPORT_EMMC_CONFIG to the Kconfig file. This is present upstream
but not in 19.01 yet.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch configures the pinmux settings for the BeagleBone AI after
the emmc read has completed.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
BeagleBoard.org BeagleBone AI rev A1 does not include a board
identifier I2C EEPROM due to a design oversight. These boards have
been put into production and are generally available now.
The board identifier information, however, has been included in the
second eMMC linear boot partition (/dev/mmcblk1boot1).
This patch works by:
* First, looking for a board identifier I2C EEPROM and if not found,
* Then seeing if the boot mode matches BeagleBone AI with eMMC in the
boot chain to make sure we don't enable eMMC pinmuxes on boards
that don't support it, and
* Finally, initializes the eMMC pins and reading the header.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is an option to enable the board detection for TI platforms.
If this is option is not set, there is no reason to set the EEPROM
bus address or chip address.
This patch makes both EEPROM_BUS_ADDRESS and EEPROM_CHIP_ADDRESS
depend on TI_I2C_BOARD_DETECT.
Signed-off-by: Adam Ford <aford173@gmail.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Print the board name and ver along with the DT Model.
While at it print the ver for all the detected daughter cards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
am65x ROM support booting over UART. And U-Boot built for am65x EVM
supports UART boot as well. Add the UART boot procedure into the README
also providing a corresponding example command sequence for execution
on a host PC.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
On HS devices the access to TRNG is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add initial defconfig support for J721e that runs on A72.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add initial defconfig support for J721e that runs on R5.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS file]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs has an updated board
detection EEPROM structure that contains a TLV record of dedicated MAC
addresses rather than a range of MAC addresses as it was used on earlier
platforms such as DRA7. Add a basic function that allows us setting up
Ethernet MAC addresses into the U-Boot environment based on the MAC
address record contained in the common TI EEPROM structure.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs have an updated board
detection EEPROM structure, now comprising variable-sized TLV-type
records, containing a superset of what is already being provided on
earlier platforms such as DRA7. Add basic support for parsing the new
data structures contained on the base board into the common TI EEPROM
structure while also providing infrastructure that can be used later on
to parse data from additional EEPROMs such as the ones that are used on
daughtercards for this platform.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add instructions for flashing boot images to the eMMC with a
layout of the address where each image needs to be flashed.
Also add instructions to flash filesystem partition in user
partition and boot kernel from the rootfs.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
