Load NetXtreme firmware in board_init when BNXT_ETH is selected.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current implementation of reset_cpu() in the ns3 board code does not
archieve what it is supposed to (according to the comments), due to
a number of reasons:
1. The argument to reset_cpu() is _not_ actually passed from the
`reset` command, but is set to 0 in all call-sites (in this
specific case, see arch/arm/lib/reset.c). Thus, performing
different kinds of resets based on its value will not work as
expected.
2. Contrary to its documentation, the passed argument is not
interpreted, but a static `L3_RESET` define is used. The other
comment properly notes that this will always perform a L3 reset,
though.
3. The "parsing" of the static `L3_RESET` value is not even using the
upper and lower nibble as stated in the comment, but uses the last
two decimal digits of the value.
This is currently one of the only implementations left in U-Boot, which
make "use" of the value passed to reset_cpu(). As this is done under
false assumption (the value does not have any meaning anymore), it makes
sense to bring it into line with the rest and start ignoring the
parameter.
This is a preparation for removal of the reset_cpu() parameter across
the entire tree in a later patch.
Fixes: b5a152e7ca ("board: ns3: default reset type to L3")
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Chimp is a core in Broadcom netxtream controller (bnxt).
Add support to check bnxt's chimp component status.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend Kconfig for the board with board-specific commands selection.
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add development keys used in FIT.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default relocation happens to a higher address of DDR,
i.e, DDR start + DDR size.
U-Boot shall be used to collect the ramdump.
Restrict U-Boot to use only the 16MB memory, so that this
memory can be reserved. Limit relocation to happen within
16MB memory, start 0xFF00_0000 and end 0x1_0000_0000
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add both DRAM banks memory information and
the corresponding MMU page table mappings.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add API to save boot parameters passed from BL31
Use assembly implementation of save_boot_params instead of c function.
Because generally ATF does not set up SP_EL2 on exiting.
Thus, usage of a C function immediately after exiting with no stack
setup done by ATF explicitly, may cause SP_EL2 to be not sane,
which in turn causes a crash if this boot was not lucky to get
an SP_EL2 in valid range. Replace C implementation with assembly one
which does not use stack this early, and let u-boot to set up its stack
later.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
