Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The path in the Linux kernel dts directory is
rockchip/rk3326-odroid-go2.dtb.
That also seems to match the FDT path set on other boards (ie:
rock64-rk3328 for example).
Signed-off-by: Roger Pau Monne <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the unset of the EFI loader, it's possible for U-Boot to
provide a EFI environment on this board, and it's also required by
the FreeBSD loader which mandated EFI on Aarch64.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rock960 doesn't have SPI flash on-board, but the bits
get enabled by default which means when booting we get
some errors. Explicitly disable it to stop the errors.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop a irrelevent comment now the related configs have moved
to the various config files.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adds the needed target option and drivers needed for correct
bringup.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 + the recently added timer0 phandle
targetted at the 5.12 merge window.
With this the non-mainline nodes like the dmc move to a separate
rk3368-u-boot.dtsi that is included from the board-specific
-u-boot.dtsi files, similar to how rk3399 does this.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 in Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the STACK_R_ADDR at 0x600000 (6MB) we're competing with
with the loading address of either u-boot or atf parts, so move
that away to 0x4000000 (64MB) similar to rk3399.
Only lion currently sets that at all but not sheep the second
rk3368 board, so just move that to the Kconfig for rk3368 similar
to rk3399 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prevent running out of memory, increase SYS_MALLOC_F_LEN to 0x4000
similar to what rk3399 uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.
So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using a non-default SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR setting makes the
resulting u-boot-rockchip.bin unbootable, as it gets stuck after SPL.
Removing the setting from the defconfig allows U-Boot to load
successfully.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
misc fixes and improvements to sandbox, etc.
x86 CBFS improvements
x86 coreboot improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBfg1YRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZQnQf/UtTgrFdmvY86v4Y3sCvbdAlDHso15voU
zEwhjKoPbnchHDA0UMFn/SmP0zRZNQbIhIsASoC4OBVl8nmtAQ7nDP8SmwtV95Zo
wqPVUlCjkHID3XOFIDbqx3L6fCL1mDe33hhfdYDzeLmhcDyxofY9yTjMasxk4tcu
oMRMiFYpL6IkM7Jtey/kRzOuEykh1J/iXJ0rAHnzgHR8vzLJEo5DjLsbd971896I
87LUmZ//3b499KgTCj7MYTEFoDA36MCPQKWqIhbFv4zh3STLGCT5fri6jHWqjHYG
UU35bdgLvsE3Dv/VFg/C+YoIzbxGRYK5WCIJX4akoE/GPCgba0C9YQ==
=5gak
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28mar21' of git://git.denx.de/u-boot-dm into next
binman support for expanding entries, connections
misc fixes and improvements to sandbox, etc.
x86 CBFS improvements
x86 coreboot improvements
On RISC-V the symbols __dyn_sym_start, dyn_sym_end are referenced in
efi_runtime_relocate().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a few more internal checks to make sure offsets are correct, before
updating the dtb.
To make this easier, update the functions which add a property to return
that property,.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far we have only needed to add subnodes to empty notds, so have not
had to deal with ordering. However this feature is needed for binman's
expanded nodes, since there may be another node in the same section.
While libfdt adds new properties after existing properties, it adds new
subnodes before existing subnodes. This means that we must reorder the
nodes in the cached version, so that the ordering remains consistent.
Update the sync implementation to sync existing subnodes first, then
add new ones, then tidy up the ordering in the cached version. Update the
test to cover this behaviour.
Also improve the comment about property syncing while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new test that adds a subnode alongside an existing one, as well as
adding properties to a subnode. This will expand to adding multiple
subnodes in future patches. Put a node after the one we are adding to so
we can check that things sync correctly.
The testAddNode() test should be in the TestNode class since it is a node
test, so move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Once the tree has been synced, thus potentially moving things around in the
fdt, we set _cached_offsets to False so that a refresh will happen next
time a property is accessed.
This 'lazy' refresh doesn't really save much time, since refresh is a very
fast operation, just a single walk of the tree. Also, having the refresh
happen in the bowels of property access it makes it harder to figure out
what is going on.
Simplify the code by always doing a refresh before and after a sync. Set
_cached_offsets to True immediately after this, in the Refresh() function,
since this makes more sense than doing it in the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
If a property does not yet have an offset, then that means it exists in
the cache'd fdt but has not yet been synced back to the flat tree. Use
the dirty flag for this so we don't need to check the offset too. Improve
the comments for Prop and Node to make it clear what an offset of None
means.
Also clear the dirty flag after the property is synced.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to specify the default alignment for all entries
in a section, such as when word-alignment is necessary, for example. It
is tedious and error-prone to specify this individually for each section.
Add a property to control this for a section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Generally the content of sections is not built until the final assembly
of the image. This is partly to avoid wasting time, since the entries
within sections may change multiple times as binman works through its
various stages. This works quite well since sections exist in a strict
hierarchy, so they can be processed in a depth-first manner.
However the 'collection' entry type does not have this luxury. If it
contains a section within its 'content' list, then it must produce the
section contents, if available. That section is typically a sibling
node, i.e. not part oc the collection's hierarchy.
Add a new 'required' argument to section.GetData() to support this. When
required is True, any referenced sections are immediately built. If this
is not possible (because one of the subentries does not have its data yet)
then an error is produced.
The test for this uses a 'collection' entry type, referencing a section as
its first member. This forces a call to _BuildSectionData() with required
set to False, at first, then True later, when the image is assembled.
Signed-off-by: Simon Glass <sjg@chromium.org>
The vblock entry type includes code to collect the data from a number of
other entries (not necessarily subentries) and concatenating it. This is
a useful feature for other entry types.
Make it a base class, so that vblock can use it, along with other entry
types.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is a command-line flag to disable substitution of expanded
entries. Add an option to the entry node as well, so it can be controlled
at the node level.
Add a test to cover this. Fix up the comment to the checkSymbols() function
it uses, while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:
- two pins provided in a ternary arrangement, for 9 combinations.
- reading from the EC
Add a binding doc and drop the unused #defines as well.
Example:
U-Boot 2021.01-rc5
CPU: Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
DRAM: 3.9 GiB
MMC: sdmmc@1b,0: 1, emmc@1c,0: 2
Video: 1024x768x32 @ b0000000
Model: Google Coral (memconfig 5, SKU 3)
This depends on the GPIO series:
http://patchwork.ozlabs.org/project/uboot/list/?series=228126
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Some boards may want to show the SKU ID or other information obtained at
runtime. Allow this to come from sysinfo. The board can then provide a
sysinfo driver to provide it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is not possible to remove the state before driver model is uninited,
since the devices are allocated in the memory buffer. Also it is not
possible to uninit driver model afterwards, since the RAM has been
freed.
Drop the uninit altogether, since it is not actually necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an extra condition here since we cannot put x86 tables in a bloblist
when bloblists are not supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U_BOOT_CMDREP_COMPLETE() macro produces a build error if CONFIG_CMDLINE
is not enabled. Fix this by updating the macro to provide the 'repeatable'
arugment in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this documentation over to reST. Move the example files into a files/
directory so they are still separate.
Do a few minor updates while we are here:
- Tidy up sandbox build instructions
- Update my github account name
- Add some talks and links
Signed-off-by: Simon Glass <sjg@chromium.org>
The _SUPPORT suffix is from an earlier time and interferes with use of
the CONFIG_IS_ENABLED() macro. Rename the option to drop the suffix.
Tidy up the TODO that prompted this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature was dropped from U-Boot some time ago:
f12f96cfaf (sf: Drop spl_flash_get_sw_write_prot")
However, we do need a way to see if a flash device is write-protected,
since if it is, it may not be possible to write to do (i.e. failing to
write is expected).
I am not sure of the correct layer to implement this, so this patch is a
stab at it. If spi-flash makes sense then I will add to the 'sf' also.
Re the points mentioned in the removal commit:
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
Which uclass is this?
2) Technically there is no real hardware user for this API to
use in the source tree.
I do want coral (at least) to support this.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
This new patch only mentions write-protect being on or off, rather than
the actual mechanism.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
That sounds to me like what drivers are for. But we still need some sort
of API for it to be accessible.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootstage silently ignores new records if it runs out of
space. It is sometimes obvious by looking at the report, but the IDs are
not contiguous, so it is easy to miss.
Aad a message so that action can be taken.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two separate places that need to figure out the bootstage ID to
use. Put this code in a function so that the logic is in one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
These tests current produce unwanted output on sandbox. Use the correct
functions to controller console output, to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox is special in that it is used for testing and it does not match
any particular target architecture. Allow it to load an image from any
architecture, so that 'bootm' can be used as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when a file is bound to a host device it is always marked as
removeable. Arguably the device is removeable, since it can be unbound at
will. However while it is bound, it is not considered removable by the
user. Also it is useful to be able to model both fixed and removeable
devices for code that distinguishes them.
Add a -r flag to the 'host bind' command and plumb it through to provide
this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the 'bind' subcommand before processing the arguments. This will
make it easier to add an optional flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has a strange mix of declarations and argument parsing
which is a bit hard to follow and harder to modify. Separate out the
declarations at the start of the function and adjust the ordering of
the code slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
