This patch is to enable espi DM for T2080QDS in uboot
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
fixed-rate driver is not different from clk_fixed_factor and it is required
very early in boot that's why setup flag for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
pxe sub commands need to be manually relocated for architectures which
enables MANUAL_RELOC as Microblaze.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Map all resource for R5 to operate properly.
The patch is done based on the commit 23f7b1a776 ("armv7R: K3: am654:
Enable MPU regions") which also map the whole 4GB at first and then change
mapping for DDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ATF support was all the time based on FIT image support but this dependency
is not recorded anywhere.
For !SPL_FIT && SPL_ATF there is compilation error:
common/spl/spl.c: In function 'board_init_r':
common/spl/spl.c:689:26: error: 'struct spl_image_info' has no member named 'fdt_addr'
689 | spl_fixup_fdt(spl_image.fdt_addr);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both SOCs shouldn't have any problem with 64bit dma accesses. Also with PIE
enabled when u-boot is placed above 4GB without any memory mapped below 4GB
address space efi_memory_init() call is failing due to missing memory node.
For this two reason disable this option for ZynqMP and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
if conditions should match.
Fixes: a18d09ea38 ("fpga: zynqmp: Add secure bitstream loading for ZynqMP")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For SPL flow without specifying address for DT loading DTB is automatically
appended behind U-Boot code. Specifically _end symbol is used. Just behind
it there is place for bss section.
It means if early code is using static variable and there is a write to
this variable DTB file is corrupted if variable is located between DTB
start and end.
In this particular case offset of this variable from bss section start is
very small (0x40) that's why DT is currupted which breaks this boot flow.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable position independent pre-relocation to let users options to put
u-boot to different locations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling saving variables to MMC(FAT), NAND, SPI based on primary bootmode.
Maybe that logic can be tuned for more complicated use cases and better
tested for different bootmodes.
Tested on zcu104 to SD(FAT) and JTAG(NOWHERE).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have name variable saved in BSS section when it
doesn't need to be really used. That's why remove static from variable
definition and use strdup() to duplicate string with exact size from malloc
area instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current algorithm used to get the silicon name is bit complicated and
hard to follow. Updated to use more straightforward mechanism based on
the Device ID code table (Table 1-2). The full IDCODE register is used
(except device revision bits [31:28]) to get the device name and IDCODE2
value is used for identifying the variant.
Additionally to make the algorithm bit more clear it also save some space
as the devices table is slightly bit smaller.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add MSCC header with delay definitions for VSC8531 and associated
family devices.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It was protected just for SPL_OS_BOOT but this function is only called when
SPL_ATF is enabled that's why change macro name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Value of shunt resistor for INA226s that monitor VCCINT and VCC_SOC power
rails are incorrect. This patch corrects those values.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
There is 2nd pca9548 mux on I2C1 bus that controls SFP0, SFP1, and QSFP1
ports. Channel 0 and 1 are connected to J287 connector for SFP0 & SFP1, and
channel 2 is connected to J288 connector for QSFP1.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add CONFIG_XILINX_UARTLITE config to versal/zynqmp defconfig to
enable uartlite driver support by default.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This endinness changes are taken from linux uartlite driver.
Reset TX fifo in control register and check TX fifo empty
flag in lower byte of the status register to detect if it
is a little endian system. Based on this check, program the
registers with le32 or be32 through out the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable required configs for using ubifs in uboot.
UBIFS testing procedure from u-boot:
Let's say we have two partitions in dt as below and want to format
partition1 "images" with ubifs.
partition@0 {
label = "boot";
reg = <0x0 0x1000000>;
};
partition@1 {
label = "images";
reg = <0x1000000 0x7000000>;
};
We will format the partition from linux and copy some files and access
from uboot later.
First thing, in linux config disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS.
this is required as ubifs expects min LEB size as 15*1024 bytes.
Use below commands in linux to format "images" partition with ubifs.
ubiformat /dev/mtd1
ubiattach /dev/ubi_ctrl -m 1
ubimkvol /dev/ubi0 -N images -m
mount -t ubifs ubi0:images /mnt
We can copy files to /mnt and unmount it.
To access this ubifs partition from uboot, run below commands.
(Don't forget to probe device before, e.g. sf probe 0 0 0)
setenv mtdids "nor0=nor0"
setenv mtdparts "mtdparts=nor0:16m(boot),112m(images)"
ubi part images
ubifsmount ubi0:images
make sure we match "mtdparts" to whatever is given in dt w.r.t partition
sizes.
"mtdparts" command will list the mtd partitions in u-boot.
Once ubifs is mounted, we can use "ubifsls" to list the files in that
partition and use "ubifsload <addr> <filename>" to load files from ubifs
partition to DDR.
Reading information about mtd layout from DT is not supported.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add read/write memory utilities for 16 and 32 bits. Add these
api's for both little and big endian systems similar to arm
architecture.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot on xilinx boards is checking one address where DTB can be placed as
the first location for DTB. Originally this code was developed for Versal
where QEMU was putting generated DTB for U-Boot to use.
The patch enables changing this address which is necessary for cases where
default address is pointing to location (DDR) which is not present. The
access to this location can cause exception.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not source xilinx board Kconfig by other boards. These configs should be
available only when Xilinx platforms are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
