PALMAS PMIC family has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS65910/TPS65911 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS80031/TPS80032 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX77663 PMIC has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS80031/TPS80032 PMICs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dev->driver_data will carry the tail of ldo if there is a number and
if there is no number it will be an error code, anyway it will not be
zero. This results in a wrong ldo regulator detection.
To avoid this check for non-numerical ldo first and then manipulate
dev->driver_data.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Existing PALMAS PMIC driver is fully compatible with TI TPS65913
PMIC found in many Tegra 4 devices, like Tegra Note 7 and ASUS
TF701T. TPS65913 shares same structure of regulators like TPS659038
so data can be reused.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # NVIDIA Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The commit 85dc582892 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.
Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
The commit 30975fb73d ("rockchip: Add option to prevent booting on
power plug-in") introduce an option to prevent booting a device when the
device was powered on due to power plug-in instead of pressing a power
button.
This feature works by checking the power-on source during PMIC probe
and powers off the device if power-on source was power plug-in.
This check currently runs very late at PMIC probe in U-Boot proper.
Fix so that the power-on source check can work at probe time in SPL.
Also enable probe after bind and remove the PMIC banner in SPL.
With this we can use ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON and
SPL_PMIC_RK8XX to power off the device very quickly after TPL instead
of after TF-A and U-Boot proper has been loaded and run.
DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB
change to: 324MHz
clk skew:0x64
change to: 528MHz
clk skew:0x58
change to: 780MHz
clk skew:0x58
change to: 1056MHz(final freq)
clk skew:0x40
out
Power Off due to plug-in event
Fixes: 30975fb73d ("rockchip: Add option to prevent booting on power plug-in")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Select SYSRESET_CMD_POWEROFF to use the sysreset implementation of the
poweroff command when PMIC_RK8XX is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The voltage value for switchout converters is always reported as 0 uV.
When the switch is enabled, it's voltage is same as input supply.
Fix this by implementing get_value for switchout converters.
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Information from the first range group is always used to calculate the
voltage returned for buck converters. This may result in wrong voltage
reported back to the regulator_get_value caller.
Traverse all the possible BUCK ranges to fix this issue.
Fixes: addd062bea ("power: pmic: rk816: support rk816 pmic")
Fixes: b62280745e ("power: pmic: rk805: support rk805 pmic")
Fixes: b4a35574b3 ("power: pmic: rk817: support rk817 pmic")
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, simplify buck get_value, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
A quick power cycle of a LDO regulator during dw-mmc signal voltage
change has shown that SD-card does not always get recognized.
Linux driver use an enable_time of 400us for LDO regulators. Apply a
500us delay when a LDO regulator is enabled to fix possible issues.
Fixes: 94afc1cb46 ("power: regulator: rk8xx: update the driver for rk808 and rk818")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: elaine.zhang<elaine.zhang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 12df2c182ccb ("regulator: dt-bindings: fixed-regulator: allow
gpios property") in linux v6.3-rc1 added support for use of either a
gpios or gpio prop with a fixed-regulator.
This adds support for the new gpios prop to the fixed-regulator driver.
gpios prop is used by vcc3v3-pcie-regulator on Radxa ROCK 3 Model A.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the imx8m power domain kernel driver, there is an extra udelay(5)
prior to requesting the domain to power up:
https://github.com/torvalds/linux/blob/v6.3/drivers/soc/imx/gpcv2.c#L347-L375
Haven't observed any issues due to the lack of this delay in U-Boot yet,
but better to align it with the kernel driver implementation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The regulator core can return different codes which are not considered
a real error for this function.
Return success in such cases.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Simplify the subsystem by renaming `dev_pdata` to just `plat`.
No functional change, just trivial renaming.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Some devices share a regulator supply, when the first one will request
regulator disable, the second device will have it's supply cut off before
graciously shutting down. Hence there will be timeouts and other failed
operations.
Implement a reference counter mechanism similar with what is done in
Linux, to keep track of enable and disable requests, and only disable the
regulator when the last of the consumers has requested shutdown.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch adds Power controller driver support for Amlogic
A1 family using secure monitor calls. The power domains register
only can access in secure world.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230531093156.29240-4-avromanov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The '_' character is discouraged in the node name, this patch adds the
new prefix of regulator subnode, with the '-' character, in STM32MP1 driver
to support the new naming rule in Linux kernel device trees.
It is a preliminary patch before Linux device tree synchronization
for STMicroelectronics boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This driver is not used and has lain unconverted since:
fc47cf9d05 arm: exynos: i2c: Convert exynos boards to use DM_I2C
Drop it and the entire mfd directory, since there is nothing left.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver and bat_trats2 are not used. Drop them and the entire battery
directory, since there is nothing left.
Signed-off-by: Simon Glass <sjg@chromium.org>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that a regulator driver exists for this PMIC, hook it up to the
device tree "regulators" subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver handles most voltage regulators found in X-Powers AXP PMICs.
It is based on, and intended to replace, the regulator driver in TF-A.
AXP PMIC regulators can be divided into 6 categories:
- Switches without voltage control => fully supported.
- Single linear range => fully supported.
- Two linear ranges, "step" and "2 * step" => fully supported.
- Two linear ranges, "step" and "5 * step" => only the first range is
supported. No boards are known to use the second range.
- Non-linear voltage values => fully supported.
- LDOs shared with GPIO pins => not supported.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Subordinate regulator drivers can use this enumerated ID instead of
matching the compatible string again.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
