All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
The PSCI_RESET and EXPERT are not needed for mini configurations so remove
them to save space.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables 2 nand chips support for zynqmp mini nand
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define default address via Kconfig. There is no need to change this address
for most of the boards but it is also possible. This one line save a lot of
lines in defconfigs that's why make sense to do it.
The similar change has been done by commit 9340d8fe8b
("sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
These boards don't have a watchdog enabled in SPL, so make sure
CONFIG_SPL_WDT is not enabled.
Fixes: commit 6874cb7220 ("watchdog: Split WDT from SPL_WDT")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
When booting through the efi stub, the memory map get's created by
reading the dram bank information. Depending on the version of the RPi4
this information changes. Read the device tree to initialize the dram
bank data structure. This way the kernel is able to access the whole
range of available memory.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This patch enables the BBT in NAND on the AT91SAM based GARDENA smart
Gateway. This is especially important, since the Linux driver also
enables this option and uses the BBT table pages. Without setting this
option, U-Boot will try to re-use these pages again (e.g. UBI).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
Define "splashimage" variable in the default environment
and enable BMP code. Also configure white on black for
video console.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
After mxc_ipuv3 DM_VIDEO conversion showing splash image
doesn't work. Fix this. Also enable white on black console
configuration as it used to be with cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
After mxc_ipuv3 DM_VIDEO conversion showing splash image
doesn't work. Fix this. Also enable white on black console
configuration as it used to be with cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We need a new STACK in SDRAM instead of SRAM so that the EMMC controller
can work properly. The EMMC/SD controller's master is not able to access
SRAM area, it can only access DRAM area.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
SPL_TEXT_BASE is 0x0 by default, based on the kconfig
definition move in below commit.
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133ee)
So, don't define it explicitly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPL sets up SDRAM while in its board_init_f()
function, it is possible for the stack to move
there before board_init_r() is reached.
So it is required to reserve the stack for SDRAM,
with a proper location and size otherwise any
operations during SPL handoff would leads to failure.
On, this particular context tinker-rk3288 SPL is
failing to launch U-Boot proper on SDRAM due to
lack of stack.
U-Boot SPL 2019.10-rc3-00297-g5ba8b12543 (Sep 12 2019 - 08:50:36 +0530)
Trying to boot from MMC1
spl: mmc init failed with error: -110
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
So, enable SPL_STACK_R_ADDR and it's related-config
items for SDRAM, SPL stack to setup properly.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPL_TEXT_BASE is 0x0 by default, based on the kconfig
definition move in below commit.
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133ee)
So, don't define it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The initial Vyasa-rk3288 TPL implementation is to reuse the
SPL_TEXT_BASE for TPL and SPL as 0x0 and 0xff704000 respectively.
But the below commit implements the reverse way of using TEXT_BASE's
like 0xff704000 for TPL and 0x0 for SPL and which indeed update
the SPL_TEXT_BASE for vyasa-rk3288 board.
"rockchip: Kconfig: enable TPL support for rk3328"
(sha1: 3f47db0275)
So, fix by dropping the legacy SPL_TEXT_BASE and it will
reassign 0x0 by default based on Kconfig definition.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This enables reading the cpuid from e-fuse, and deriving a static
MAC address from it. Without this, the ethernet interface on the
rockpro64 can't be used to boot.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the "dhcp" command as a minor convenience.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
HS devices use the FIT post processing step to authenticate boot images.
Set the configured boot command to load FIT by default.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The da8xx GPIO driver is available with DM_GPIO support. This
patch enables the CMD_GPIO, CMD_DM, and DM_GPIO and DA8XX_GPIO.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USB was just recently enabled, so it is unlikely anyone is
using it in SPL, so this patch removes it from SPL to further
reduce the SPL code size.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable driver model for USB, MMC, SPI and SPI_FLASH. Also enable BLK.
This will remove the following compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
lx2160a rev1 and rev2 SoC has different pcie controller.
The pcie controller device tree node fields "compatible"
and registers names needs to be updated accordingly
This change in device tree is handled as part of
fdt fixups. These changes would only be applied
if the soc revision is not rev1.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
This defines a minimum defconfig for each of the two Raspberry Pi 4
variants. One notable difference is that we don't have a embedded dt for
this board given that the fw supplies us with one which we can reuse.
Furthermore, the ram size is not queryable through mbox interface as the
maximum reported size is 1G. The fw patches the dt with the right
memory configuration and uboot uses it as it is. We avoid u-boot
touching this configuration by making sure CONFIG_ARCH_FIXUP_FDT_MEMORY
is deactivated.
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable CONFIG_CMD_BOOTEFI_SELFTEST for the QEMU RISC-V boards.
Travis CI QEMU testing has been enabled for qemu-riscv64_defconfig. With
this patch we will test the UEFI sub-system on the board.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the MMC subsystem and the Aspeed SD controller. Also enable the
use of the device tree for probing the controller.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
If the "Page Mode" is not enabled on the device,
read operations from PSRAM may result in incorrect data.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add DT entry for the DM PCI driver, update board configs
and drop ad-hoc board init code for the PCI bus. Instead,
let the DM PCI driver initialize and operate the hardware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable OF control for SH4 R2Dplus board. This is necessary, because
the PCI uclass is designed in a way that makes it depend on DT and
disallows instanciating devices without DT (e.g. with platdata).
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable driver model support for SH4 R2Dplus board. Thus far, no
drivers are bound via the DM. The PCI drivers have yet to be
converted to DM_PCI.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
