The SPL payload offset when booting from SPI defaults to
CONFIG_SYS_SPI_U_BOOT_OFFS but can be overridden by
u-boot,spl-payload-offset. The Device Tree for Puma Haikou has this
property so there's no need to have this one option in the defconfig,
especially since they are not in sync and therefore confusing.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chances are when one boots U-Boot proper from a given storage medium,
they want the same medium to be used to load and store the environment.
This basically allows to have completely separate U-Boot (TPL/SPL/U-Boot
proper/environment) per storage medium which is convenient when working
with recovery from SD-Card as one would just need to insert a properly
configured SD-Card into the device to have access to their whole debug
setup.
No fallback mechanism is provided as to not dirty other storage medium
environment by mistake. However, since arch_env_get_location() is called
by env_init() which is part of the pre-relocation process, a valid,
non-ENVL_UNKNOWN, value shall be returned otherwise the relocation fails
with the following message:
initcall sequence 00000000002866c0 failed at call 0000000000256b34 (err=-19)
This valid, non-ENVL_UNKNOWN, value is ENVL_NOWHERE which requires to
always select CONFIG_ENV_IS_NOWHERE otherwise this work-around does not
work.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There's a SPI-NOR flash available from which SPL and U-Boot proper can
be booted, it makes sense to also allow this medium to store U-Boot
environment so let's enable it.
The Device Tree advertises a max frequency of 50MHz so let's set the
config option appropriately.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Automatically detect which MMC device (SD-Card or eMMC) was used to load
U-Boot proper and load the environment from that MMC device instead of
a hardcoded one.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_ENV_OFFSET is set in the defconfig to a different value already
so this isn't used. Let's remove it as to not confuse users.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Trying to load U-Boot proper from SPL when SPL was not loaded from
SD-Card is currently not working because the SDMMC pins aren't muxed
correctly. It is assumed the BootROM is doing this for us when booting
from SD-Card hence why it's not needed when booting TPL/SPL from
SD-Card.
The pinctrl properties are removed from the SPL DT property removal list
and the pinctrl configuration nodes made available in the SPL DT, in
addition to the pull-up configurations to allow loading U-Boot proper
from SD-Card as a fallback mechanism for SPI-NOR and eMMC.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force
booting from SD card or USB via rkdeveloptool by toggling a switch. This
switch needs to be overridden in software to be able to access eMMC and
SPI-NOR once the device has booted from SD Card. Puma SoM can override
this pin via gpio3_d5.
Until now, fixed regulator device was abused to model this, but since
there's now support for GPIO hogs, let's use it.
Since we want to be able to boot the SPL from SD Card but give it the
ability to load U-Boot proper from a fallback medium such as eMMC and
SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for
other kinds of regulators are not needed anymore, so let's disable them.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
distroboot should try first on the same MMC medium as the one the SPL
loaded U-Boot proper from. This was the case when the introducing commit
was merged because the default order was eMMC first and then SD card.
The check was therefore made only on whether we booted from SD card,
because otherwise the order was the expected one.
However, in commit b212ad24a6 ("rockchip: Fix MMC boot order"), the
order was swapped. Meaning our simple check is now useless.
Let's fix that by accounting for all scenarii: default boot_targets has
mmc0 first but booting from SD Card, mmc1 first but booting from eMMC.
Fixes: b212ad24a6 ("rockchip: Fix MMC boot order")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1 work in otg mode
- 12V DC Power supply
The dts file is sync from linux-next[0].
[0]:https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SERIAL_TAG is not selectable for ARM64 machines. While
get_board_serial is weakly defined if ENV_VARS_UBOOT_RUNTIME_CONFIG is
defined, it is only called when CONFIG_SUPPORT_PASSING_ATAGS is defined,
which also is not selectable for ARM64 machines. Therefore this is dead
code so let's remove it.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RAM_PX30_DDR4 is for DDR4 support and not DDR3 so let's fix the typo.
Fixes: 2db36c64bd ("ram: rockchip: px30: add a config-based ddr selection")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
UART0 can obviously also be used for debug uart in U-Boot, so let's add
its support.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The check to perform is on CONFIG_SPL_GPIO and not SPL_GPIO.
Because this was never compiled in, it missed an include of cru.h that
was not detected before. Let's include it too.
Also switch to IS_ENABLED in-code check as it is the preferred
inclusion/exclusion mechanism.
Fixes: 07586ee432 ("rockchip: rk3399: Support common spl_board_init")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The check to perform is on CONFIG_SPL_DM_REGULATOR and not
SPL_DM_REGULATOR. Also switch to in-code check instead of ifdefs.
Fixes: 07586ee432 ("rockchip: rk3399: Support common spl_board_init")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com> # Rock960
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The original code set up the DDR clock to 48 MHz, not 50MHz as
requested, and did it in a way that didn't satisfy the Application
Notes in RK3399 TRM [1]. 2.9.2.B says:
PLL frequency range requirement
[...]
FOUTVCO: 800MHz to 3.2GHz
2.9.2.A :
PLL output frequency configuration
[...]
FOUTVCO = FREF / REFDIV * FBDIV
FOUTPOSTDIV = FOUTVCO / POSTDIV1 / POSTDIV2
FREF = 24 MHz
The original code gives FOUTVCO: 24MHz/1 * 12 = 288MHz < 800MHz
And the resulting FOUTPOSTDIV is 288MHz / 3 / 2 = 48MHz
but the requested frequency was 50MHz
Note:
2.7.2 Detail Register Description
PMUCRU_PPLL_CON0 says
fbdiv
Feedback Divide Value
Valid divider settings are:
[16, 3200] in integer mode
So .fbdiv = 12 wouldn't be right. But 2.9.2.C says:
PLL setting consideration
[...]
The following settings are valid for FBDIV:
DSMPD=1 (Integer Mode):
12,13,14,16-4095 (practical value is limited to 3200, 2400, or 1600
(FVCOMAX / FREFMIN))
[...]
So .fbdiv = 12 would be right.
In any case FOUTVCO is still wrong. I thank YouMin Chen for
confirmation and explanation.
Despite documentation, I don't seem to be able to reproduce a
practical problem with the wrong FOUTVCO. When I initially found it I
thought some problems with detecting the RAM capacity in my Rock Pi 4B
could be related to it and my patch seemed to help. But since I'm no
longer able to reproduce the issue, it works with or without this
patch. And meanwhile a patch[2] by Lee Jones and YouMin Chen addresses
this issue. Btw, shouldn't that be commited?
So this patches solves no visible problem. Yet, to prevent future
problems, I think it'd be best to stick to spec.
An alternative to this patch could be
{.refdiv = 1, .fbdiv = 75, .postdiv1 = 6, .postdiv2 = 6};
This would theoretically consume more power and yield less jitter,
according to 2.9.2.C :
PLL setting consideration
[...]
For lowest power operation, the minimum VCO and FREF frequencies
should be used. For minimum jitter operation, the highest VCO and
FREF frequencies should be used.
[...]
But I haven't tried it because I don't think it matters much. 50MHz
for DDR is only shortly used by TPL at RAM init. Normal operation is
at 800MHz. Maybe it's better to use less power until later when more
complex software can control batteries or charging or whatever ?
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Link: [1] https://opensource.rock-chips.com/images/e/ee/Rockchip_RK3399TRM_V1.4_Part1-20170408.pdf
Link: [2] https://patchwork.ozlabs.org/project/uboot/list/?series=305766
Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Partial sync of rk3288.dtsi from Linux version 5.18
Changed:
only properties and functions that are not yet included
swap some clocks positions
fix some irq numbers
style and sort nodes
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version update the cpu and gpu nodes.
Changed:
use operating-points-v2
update thermal for all cpus
add labels to all cpus
change gpu compatible
change gpu interrupt names
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move thermal sub nodes to the dtsi
file and remove rk3288-thermal.dtsi
Changed:
replace underscore in nodename
remove comments about sensor and ID
use gpu phandle
add #cooling-cells to gpu node
lower critical temparature
remove linux,hwmon property
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is not needed or used, and adds code size. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The phycore_rk3288 board has a SPL size problem,
so remove phycore_init() function to stay within the limits.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loadfile2 code is installing two protocols on it's own handle
and uses efi_delete_handle() to clean it up on failure(s). However
commit 05c4c9e21a ("efi_loader: define internal implementations of
install/uninstallmultiple") prepares the ground for us to clean up
efi_delete_handle() used in favor of Install/UninstallMultipleProtocol.
While at it clean up the non needed void casts to (void *) on the
protolcol installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* don't use EFI_CALL() for variable services
* don't use runtime pointer to access exported function
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This function is already defined in spi.h but no implementation of it
currently exists in the tree. The implementation is based on the static
function spi_set_speed_mode(). The function prototype is modified so
that an success or error condition can be returned to the caller.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Space key is indicated by two different bits. Some HW models indicate press
of space key only by the first bit. Qemu indicates it by both bits at the
same time, which is currently interpreted by u-boot as double key press.
Fix this issue by setting first bit when only second is set (to support HW
models which indicate press only by second bit) and always clearing second
bit before processing to not report double space key press.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fix typo that was caused by the same feature being split in to 2 different
configuration options. Replace CONFIG_USBNET_DEVADDR with
CONFIG_USBNET_DEV_ADDR
Signed-off-by: Ignacio Zamora <nachopitt@gmail.com>
MSM SMEM driver is currently missing <linux/sizes.h> header and throws
the following compile error:
drivers/smem/msm_smem.c: In function ‘qcom_smem_get_ptable’:
drivers/smem/msm_smem.c:635:71: error: ‘SZ_4K’ undeclared (first use in this function)
635 | ptable = smem->regions[0].virt_base + smem->regions[0].size - SZ_4K;
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: luka.perkov@sartura.hr
The test relies on memory being available at 0x0. This in not valid for
many boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the CCF is activated, the dev->parent is not necessary
the reference to SCMI transport and the function devm_scmi_of_get_channel
failed for the registered SCMI clock, child for protocol@14,
the channel is null and the SCMI clock driver crash for any operations.
This patch changes the first parameter of the ops of_get_channel(),
aligned with other process_msg() to pass directly the good reference,
i.e. parent result of find_scmi_transport_device(dev)
which return the reference of the scmi transport device.
Fixes: 8e96801aa6 ("firmware: scmi: add multi-channel support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
To allow easily iterate over all UBI volumes, add a new command which
either print all user UBI volumes on output or set them into env variable.
As UBI volumes can have arbitrary name/label, in most cases it is useful to
iterate them by their numbers. This can be achieved by -numeric flag.
This functionality is similar to already existing 'part list' command which
prints partitions on formatted block device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Provide a simple sandbox driver for the thermal uclass.
It simply registers and returns 100 degrees C if requested.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, there is no way for users to check the readings from thermal
sensors from U-boot console, only some boards print it during boot.
So, lets add a simple "temperature" command that allows listing thermal
uclass devices and getting their value.
Note that the thermal devices are intenionally probed if list is used as
almost always they will not get probed otherwise and there is no way for
users to manually call probe on a certain device from console.
Assumption is made that temperature is returned in degrees C and not
milidegrees like in Linux as this is what most drivers seem to return.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add xxd command to print file content as hexdump to standard out
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Roger Knecht <rknecht@pm.me>
This buffer has the concatenated prefix and name written into it, so it
must be large enough to cover both strings plus the terminating NUL.
Fixes: 92c4a95ec7 ("pinctrl: Add new function pinctrl_generic_set_state_prefix()")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setting an alternative signature info node in "pre_load_sig_info_path"
allows verification of an image using the bootm pre-load mechanism with
a different key, e.g.: setenv pre_load_sig_info_path "/alt/sig" ; bootm
preload [addr]
Signed-off-by: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Putting these definitions in a header will allow signatures to be
validated independently of bootm.
Signed-off-by: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix a copy-paste error I did when inserting the comment.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The option SHA256_ALGO does not exist. Remove selecting it.
Fixes: 26dd993657 ("lib: add crypt subsystem")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
This adds keyword devicetree-overlay as an alias for fdtoverlays in
extlinux (sysboot) and pxe to better follow the Boot Loader Specification
[1], improves documentation around them by adding an example for both
fdtoverlays and devicetree-overlay and the environment variable required
for this feature. The link for the spec is updated to the current one.
[1] https://systemd.io/BOOT_LOADER_SPECIFICATION/
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
