Commit graph

108 commits

Author SHA1 Message Date
Kishon Vijay Abraham I
a17188c1c2 board: ti: DRA7: added USB initializtion code
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in dra7xx board file that
can be invoked by various gadget drivers.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
2015-04-14 05:48:11 +02:00
Praveen Rao
5f603761c3 ARM: DRA7 / OMAP5: Add workaround for ARM errata 798870
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."

An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.

Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:29:01 -04:00
Lubomir Popov
b558af8128 ARM: OMAP5: DRA7xx: Add support for power rail grouping
On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC
core rails. This concept of using one SMPS to supply multiple
core domains (in various, although limited combinations, per
primary device use case) has now become common and is used by
many customer J6/J6Eco designs; it is supported by a number of
corresponding PMIC OTP versions.

This patch implements correct operation of the core voltages
scaling routine by ensuring that each SMPS that is supplying
more than one domain shall be written only once, and with the
highest voltage of those fused in the SoC (or of those defined
in the corresponding header if fuse read is disabled or fails)
for the power rails belonging to the group.

The patch also replaces some PMIC-related magic numbers with
the appropriate definitions. The default OPP_NOM voltages for
the DRA7xx SoCs are updated as well, per the latest DMs.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
2015-01-29 12:00:49 -05:00
Felipe Balbi
d11ac4b56d arm: omap: add support for am57xx devices
just add a few ifdefs around because this
device is very similar to dra7xxx.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:14 -05:00
Felipe Balbi
c27cd33b8c arm: omap5: tps659038: rename regulator defines
Those regulators don't have any coupling with
what they supply, so remove the suffixes in order
to not confuse anybody.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 11:04:13 -05:00
pekon gupta
9352697aa0 board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
     SW5.1 (NAND_BOOTn) = OFF (logic-1)
     SW5.2 (NOR_BOOTn)  = ON  (logic-0) /* Active-low */
     SW5.3 (eMMC_BOOTn) = OFF (logic-1)
     SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
     SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
     SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
     SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
     SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
     SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
     SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
     SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
     SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
2014-08-25 10:48:12 -04:00
Tom Rini
939911a64b armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_context
The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same.  In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.

Cc: Sricharan R. <r.sricharan@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-05-23 19:40:05 -04:00
Lokesh Vutla
ee77a2389b ARM: DRA72x: Add Silicon ID support
Add silicon ID code for DRA722 silicon.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-05-23 19:40:04 -04:00
pekon gupta
cd324a6dd2 ARM: omap5: add platform specific info for GPMC and ELM controllers
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.

Platform specific information added into arch-xx/../hardware.h
 - CPU related platform specific details like base-address of GPMC and ELM

Platform specific information added into arch-xx/../mem.h
 - Generic configs for GPMC and ELM initialization.
 - Hardware parameters or constrains specific to GPMC and ELM IP like;
   number of max number of chip-selects available

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-05-23 16:12:02 -04:00
Dmitry Lifshitz
d57b649e6c ARM: OMAP5: add CKO buffer control mask
Add CKOBUFFER_CLK_EN bit mask enabling FREF_XTAL_CLK clock.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
2014-05-13 19:43:00 -04:00
Dmitry Lifshitz
4b5d383924 ARM: OMAP5: add UART4 support
Add UART4 base address.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
2014-05-13 19:43:00 -04:00
Wolfgang Denk
4e4685027c ARM: OMAP: hide custom bit manipulation function sr32()
The only remaining user of the custom bit manipulation function sr32()
is arch/arm/cpu/armv7/omap3/clock.c, so  make it a static function in
that file to prepare complete removal.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-04-17 14:39:54 -04:00
Marek Vasut
463bb19eeb spl: Fix guardian macros in spl.h
Fix the macros guarding the spl.h header for various platforms. Due to
a typo and a propagation of it, the macros went out-of-sync with their
ifdef check, so fix this.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
2014-03-28 15:06:30 -04:00
pekon gupta
6aff050988 mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
51d192c40d mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common omap_gpmc.h
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
Dan Murphy
e9024ef27d ARM: O5/dra7xx: Add SATA boot support
Add the SATA boot support for OMAP5 and dra7xx.

Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.

Added the ROM boot device ID for SATA.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-19 10:47:45 -05:00
Nishanth Menon
194dd74ad9 DRA7: add ABB setup for MPU voltage domain
Patch adds modification to shared omap5 abb_setup() function, and
proper registers definitions needed for ABB setup sequence. ABB is
initialized for MPU voltage domain at OPP_NOM.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Nishanth Menon
3ac8c0bf65 DRA7: Add support for ES1.1 silicon ID code
ES1.1 silicon is a very minor variant of ES1.0. Add priliminary support
for ES1.1 IDCODE change.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Jassi Brar
e81f63f0d2 ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALL
The commit
f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls"
removed the config option aimed towards moving that stuff into kernel, which
renders some code unreachable. Remove that code.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-24 09:38:39 -05:00
Roger Quadros
a087a7fb92 ARM: OMAP5: Add SATA platform glue
Add platform glue logic for the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
Roger Quadros
8ffcf74bb0 ARM: OMAP5: Add PRCM and Control information for SATA
Adds the necessary PRCM and Control register information for
SATA on OMAP5.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:09 -05:00
SRICHARAN R
6c70935d75 ARM: DRA: EMIF: Change DDR3 settings to use hw leveling
Currently the DDR3 memory on DRA7 ES1.0 evm board is enabled using
software leveling. This was done since hardware leveling was not
working. Now that the right sequence to do hw leveling is identified,
use it. This is required for EMIF clockdomain to idle and come back
during lowpower usecases.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-12-04 08:12:08 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
SRICHARAN R
42d4f37b79 ARM: OMAP5: DDR3: Change io settings
The change from 0x64656465 to 0x64646464 is to remove the weak pull
enabled on DQS, nDQS lines. This pulls the differential signals in the
same direction which is not intended. So disabling the weak pulls improves
signal integrity.

On the uEVM there are 4 DDR3 devices.  The VREF for 2 of the devices is powered by
the OMAP's VREF_CA_OUT pins.  The VREF on the other 2 devices is powered by the OMAP's
VREF_DQ_OUT pins.  So the net effect here is that only half of the DDR3 devices were being
supplied a VREF!  This was clearly a mistake.  The second change improves the robustness of
the interface and was specifically seen to cure corruption observed at high temperatures
on some boards.

With the above two changes better memory stability was observed with extended
temperature ranges around 100C.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-11-01 15:56:00 -04:00
Minal Shah
a13cbf5f20 dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 build
UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).

Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:56:00 -04:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
41b667b834 usb: omap: Move the xhci-omap header file to common location
Moving the xhci-omap header to a more global location so that
other code can reference this code.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Dan Murphy
2d2358ac15 OMAP5: USB: Add OMAP xHCI file and header
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Dan Murphy
d861a333da ARM: OMAP5: Add registers and defines for USBOTG SS
Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:39 +02:00
Matt Porter
c97a9b3275 omap5: add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:50 +05:30
Nobuhiro Iwamatsu
9346d54366 arm: omap5: echi: Add GPL-2.0+ SPDX-License-Identifier
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-09-20 10:30:54 -04:00
Albert ARIBAUD
e62d5fb0da Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-09-04 14:06:56 +02:00
Tom Rini
c3799fceda omap5: Expand CONFIG_SPL_MAX_SIZE and comment upon SRAM_SCRATCH_SPACE_ADDR
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x.  This is required for
peripheral boot modes such as UART.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28 11:44:58 -04:00
Dan Murphy
d3d037ae18 ARM: OMAP5: USB: Add OMAP5 common USB EHCI information
* Enable the OMAP5 EHCI host clocks
* Add OMAP5 EHCI register definitions
* Add OMAP5 ES2 host revision

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26 21:55:46 +02:00
Wolfgang Denk
bcd4d4eb2b SPDX-License-Identifier: fixing some problematic GPL-2.0 files
Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files:  the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.

Insert a GPL-2.0 SPDX-License-Identifier to fix this.

Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
2013-08-19 15:34:13 -04:00
Mugunthan V N
b1e26e3bfb ARM: DRA7xx: Add CPSW support to DRA7xx EVM
Adding support for CPSW Ethernet support found in DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
fbbbc86e8e Merge branch 'master' of git://git.denx.de/u-boot-arm
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.

Conflicts:
	arch/arm/dts/exynos5250.dtsi

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-12 10:36:48 -04:00
Axel Lin
87bd05d78f ARM: OMAP: GPIO: Fix valid range and enable usage of all GPIOs on OMAP5
The omap_gpio driver is used by AM33XX, OMAP3/4, OMAP54XX and DRA7XX SoCs.
These SoCs have different gpio count but currently omap_gpio driver uses hard
coded 192 which is wrong.

This patch fixes this issue by:
1. Move define of OMAP_MAX_GPIO to all arch/arm/include/asm/arch-omap*/gpio.h.
2. Update gpio bank settings and enable GPIO modules 7 & 8 clocks for OMAP5.

Thanks for Lubomir Popov to provide valuable comments to fix this issue.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Acked-by: Heiko Schocher <hs@denx.de>
2013-07-02 09:21:16 -04:00
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Lubomir Popov
ee28edac43 OMAP5: Enable access to auxclk registers
auxclk0 and auxclk1 are utilized on some OMAP5 boards.
Define the infrastructure needed for accessing them
without using magic numbers.

Also remove unrelated TPS62361 defines from clocks.h

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-06-10 08:54:46 -04:00
Sricharan R
92b0482c17 ARM: DRA7xx: EMIF: Change settings required for EVM board
DRA7 EVM board has the below configuration. Adding the
settings for the same here.

   2Gb_1_35V_DDR3L part * 2 on EMIF1
   2Gb_1_35V_DDR3L part * 4 on EMIF2

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
7f36c88f64 ARM: DRA7xx: Update pinmux data
Updating pinmux data as specified in the latest DM

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
2013-06-10 08:43:10 -04:00
Balaji T K
a5d439c2d3 mmc: omap_hsmmc: Update pbias programming
Update pbias programming sequence for OMAP5 ES2.0/DRA7

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Sricharan R
81ede187c3 ARM: DRA7xx: Correct SRAM END address
NON SECURE SRAM is 512KB in DRA7xx devices.
So fixing it here.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Sricharan R
f9b814a8e9 ARM: DRA7xx: Correct the SYS_CLK to 20MHZ
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Nishanth Menon
18c9d55ac6 ARM: OMAP5: DRA7xx: support class 0 optimized voltages
DRA752 now uses AVS Class 0 voltages which are voltages in efuse.

This means that we can now use the optimized voltages which are
stored as mV values in efuse and program PMIC accordingly.

This allows us to go with higher OPP as needed in the system without
the need for implementing complex AVS logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
63fc0c775c ARM: DRA7xx: power Add support for tps659038 PMIC
TPS659038 is the power IC used in DRA7XX boards.
Adding support for this and also adding pmic data
for DRA7XX boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Lokesh Vutla
4de28d7921 ARM: DRA7xx: Add control id code for DRA7xx
The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00