eMMC partitions are defined as of eMMC 4.41, but mmcinfo process
partition info for eMMC >= 4.0, change it to do it for >= 4.41
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC spec numbers general purpose partitions starting at 1, but
the mmcinfo output follows the internal numbering which starts at 0.
Make the mmcinfo command output number partitions as in the eMMC
spec to avoid confusion.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This extends the mmcinfo command's output to show which eMMC partitions
have the enhanced attribute set. Note that the eMMC spec says that
if the enhanced attribute is supported then the boot and RPMB
partitions are of the enhanced type.
The output of mmcinfo becomes:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB ENH
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH
GP2 Capacity: 64 MiB ENH
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
There is currently no command that will provide an overview of the hardware
partitions present on an eMMC device, one has to switch to every partition
via "mmc dev" and run mmcinfo for each to get the partition's capacity.
This commit adds a few lines of output to mmcinfo with the sizes of the
present partitions, like this:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB
Boot Capacity: 16 MiB
RPMB Capacity: 128 KiB
GP1 Capacity: 64 MiB
GP2 Capacity: 64 MiB
panto: Minor edit removing superfluous parentheses.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.
Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.
This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.
Also, some clean up is made with errors handling and code syntax layout.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
sub-command 'bootpart-resize' check for argc == 4,
it will retrun CMD_RET_FAILURE when argc value not matched.
but bootpart-resize's maxarg is 3, which means you never execute
this sub-command successfully.
fix it by change bootpart-resize maxarg to 4.
Signed-off-by: wally.yeh <wally.yeh@atrustcorp.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pierre Aubert <p.aubert@staubli.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Currently, U-Boot behaves as follows:
- Begin with no SD card inserted in "mmc 1"
- Execute: mmc dev 1
- This fails, since there is no card
- User plugs in an SD card
- Execute: mmc dev 1
- This still fails, since the HW isn't reprobed.
With this change, U-Boot behaves as follows:
- Begin with no SD card inserted in "mmc 1"
- Execute: mmc dev 1
- This fails, since there is no card
- User plugs in an SD card
- Execute: mmc dev 1
- The newly present SD card is detected
I know that "mmc rescan" will force the HW to be reprobed, but I feel it
makes more sense if "mmc dev" always reprobes the HW after selecting the
current MMC device. This allows scripts to just execute "mmc dev", and
not have to also execute "mmc rescan" to check for media presense.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The body of init_mmc_device() is now identical to that of do_mmc_rescan()
except for the error codes returned. Modify do_mmc_rescan() to simply
call init_mmc_device() and convert the error codes, to avoid code
duplication.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This allows callers to inject mmc->has_init = 0 between finding the
MMC device, and calling mmc_init(), which forces mmc_init() to rescan
the HW. Future changes will use this feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Currently, "mmc dev 0" does not change the selected HW partition. I
think it makes more sense if "mmc dev 0" is an alias for "mmc dev 0 0",
i.e. that HW partition 0 (main data area) is always selected by default
if the user didn't request a specific partition. Otherwise, the following
happens, which feels wrong:
Select HW partition 1 (boot0):
mmc dev 0 1
Doesn't change the HW partition, so it's still 1 (boot0):
mmc dev 0
With this patch, the second command above re-selects the main data area.
Note that some MMC devices (i.e. SD cards) don't support HW partitions.
However, this patch still works, since mmc_start_init() sets the current
partition number to 0, and mmc_select_hwpart() succeeds if the requested
partition is already selected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The implementation of mmc_select_hwpart() was cribbed from do_mmcops().
Update do_mmcops() to call mmc_select_hwpart() to avoid duplication.
<panto> Manual patch update due to patch order.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This sub-command adds support for the RPMB partition of an eMMC:
* mmc rpmb key <address of the authentication key>
Programs the authentication key in the eMMC This key can not
be overwritten.
* mmc rpmb read <address> <block> <#count> [address of key]
Reads <#count> blocks of 256 bytes in the RPMB partition
beginning at block number <block>. If the optionnal
address of the authentication key is provided, the
Message Authentication Code (MAC) is verified on each
block.
* mmc rpmb write <address> <block> <#count> <address of key>
Writes <#count> blocks of 256 bytes in the RPMB partition
beginning at block number <block>. The datas are signed
with the key provided.
* mmc rpmb counter
Returns the 'Write counter' of the RPMB partition.
The sub-command is conditional on compilation flag CONFIG_SUPPORT_EMMC_RPMB
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Wolfgang Denk <wd@denx.de>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rename 'bootpart' to 'bootpart-resize' to better reflect what this
command is for.
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.
Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)
Following proposal for an implementation:
- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set
Additionally the mmc command is extended to make is possible to play around with different
DSR values.
The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch adds commands to access(open/close) and resize boot partitions on EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
The "mmc rescan" command takes no arguments. However, executing
"mmc rescan 1" succeeds, leading the user to believe that MMC device 1
has been rescanned. In fact, the "current" MMC device has been
rescanned, and the current device may well not be 1. Add error-checking
to the "mmc" command to explicitly reject any extra command-line
arguments so that it's more obvious when U-Boot isn't doing what the
user thought they asked it to.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
If a malformed 'read' or 'write' command is issued, the Sandbox U-Boot
can crash because the command-handling code does no error checking on
the number of provided arguments.
This change makes the mmc 'erase', 'read' and 'write' commands only
function if the proper number of arguments are supplied.
Also puts the else assignment at the beginning fo the if() statement
to shortens the generated code. This removes an unnecessary jump from
the generated code.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
cmd_boot.c:40:5: warning: symbol 'do_go' was not declared. Should it be static?
cmd_bootm.c:164:6: warning: symbol '__arch_preboot_os' was not declared. Should it be static?
cmd_bootm.c:477:5: warning: symbol 'do_bootm_subcommand' was not declared. Should it be static?
cmd_bootm.c:1022:1: error: directive in argument list
cmd_bootm.c:1028:1: error: directive in argument list
cmd_bootm.c:1029:1: error: directive in argument list
cmd_bootm.c:1036:1: error: directive in argument list
cmd_bootm.c:1042:1: error: directive in argument list
cmd_bootm.c:1044:1: error: directive in argument list
cmd_bootm.c:1045:1: error: directive in argument list
cmd_bootm.c:1047:1: error: directive in argument list
cmd_bootm.c:1089:5: warning: symbol 'do_iminfo' was not declared. Should it be static?
cmd_bootm.c:1176:5: warning: symbol 'do_imls' was not declared. Should it be static?
cmd_bootm.c:1654:1: error: directive in argument list
cmd_bootm.c:1660:1: error: directive in argument list
cmd_console.c:32:5: warning: symbol 'do_coninfo' was not declared. Should it be s
cmd_date.c:46:5: warning: symbol 'do_date' was not declared. Should it be static?
cmd_echo.c:27:5: warning: symbol 'do_echo' was not declared. Should it be static?
cmd_exit.c:27:5: warning: symbol 'do_exit' was not declared. Should it be static?
cmd_fat.c:97:5: warning: symbol 'do_fat_ls' was not declared. Should it be static?
cmd_fat.c:136:5: warning: symbol 'do_fat_fsinfo' was not declared. Should it be s
cmd_fdt.c:66:5: warning: symbol 'do_fdt' was not declared. Should it be static?
cmd_fdt.c:542:43: warning: incorrect type in assignment (different base types)
cmd_fdt.c:542:43: expected unsigned int [unsigned] [usertype] <noident>
cmd_fdt.c:542:43: got restricted __be32 [usertype] <noident>
cmd_fdt.c:679:42: warning: cast to restricted __be32
cmd_fdt.c:820:1: error: directive in argument list
cmd_fdt.c:822:1: error: directive in argument list
cmd_flash.c:292:5: warning: symbol 'do_flinfo' was not declared. Should it be static?
cmd_flash.c:324:5: warning: symbol 'do_flerase' was not declared. Should it be static?
cmd_flash.c:457:5: warning: symbol 'do_protect' was not declared. Should it be st
cmd_help.c:27:5: warning: symbol 'do_help' was not declared. Should it be static?
cmd_i2c.c:136:6: warning: symbol '__def_i2c_init_board' was not declared. Should it be static?
cmd_i2c.c:144:14: warning: symbol '__def_i2c_get_bus_speed' was not declared. Should it be static?
cmd_i2c.c:151:5: warning: symbol '__def_i2c_set_bus_speed' was not declared. Should it be static?
cmd_i2c.c:1322:1: error: directive in argument list
cmd_i2c.c:1324:1: error: directive in argument list
cmd_i2c.c:1326:1: error: directive in argument list
cmd_i2c.c:1328:1: error: directive in argument list
cmd_i2c.c:1337:1: error: directive in argument list
cmd_i2c.c:1339:1: error: directive in argument list
cmd_irq.c:27:5: warning: symbol 'do_interrupts' was not declared. Should it be static?
cmd_itest.c:133:5: warning: symbol 'binary_test' was not declared. Should it be static?
cmd_itest.c:158:5: warning: symbol 'do_itest' was not declared. Should it be stat
cmd_load.c:54:5: warning: symbol 'do_load_serial' was not declared. Should it be static?
cmd_load.c:431:6: warning: symbol 'his_eol' was not declared. Should it be static?
cmd_load.c:432:6: warning: symbol 'his_pad_count' was not declared. Should it be static?
cmd_load.c:433:6: warning: symbol 'his_pad_char' was not declared. Should it be static?
cmd_load.c:434:6: warning: symbol 'his_quote' was not declared. Should it be static?
cmd_load.c:436:5: warning: symbol 'do_load_serial_bin' was not declared. Should it be static?
cmd_load.c:549:6: warning: symbol 'send_pad' was not declared. Should it be static?
cmd_load.c:558:6: warning: symbol 'ktrans' was not declared. Should it be static?
cmd_load.c:568:5: warning: symbol 'chk1' was not declared. Should it be static?
cmd_load.c:578:6: warning: symbol 's1_sendpacket' was not declared. Should it be static?
cmd_load.c:587:6: warning: symbol 'send_ack' was not declared. Should it be static?
cmd_load.c:600:6: warning: symbol 'send_nack' was not declared. Should it be static?
cmd_load.c:614:6: warning: symbol 'os_data_init' was not declared. Should it be static?
cmd_load.c:615:6: warning: symbol 'os_data_char' was not declared. Should it be static?
cmd_load.c:657:6: warning: symbol 'k_data_init' was not declared. Should it be static?
cmd_load.c:663:6: warning: symbol 'k_data_save' was not declared. Should it be static?
cmd_load.c:669:6: warning: symbol 'k_data_restore' was not declared. Should it be static?
cmd_load.c:675:6: warning: symbol 'k_data_char' was not declared. Should it be static?
cmd_load.c:693:6: warning: symbol 'send_parms' was not declared. Should it be static?
cmd_load.c:694:6: warning: symbol 'send_ptr' was not declared. Should it be static?
cmd_load.c:698:6: warning: symbol 'handle_send_packet' was not declared. Should i
cmd_mdio.c:60:5: warning: symbol 'mdio_write_ranges' was not declared. Should it be static?
cmd_mdio.c:82:5: warning: symbol 'mdio_read_ranges' was not declared. Should it be static?
cmd_mdio.c:115:5: warning: symbol 'extract_reg_range' was not declared. Should it be static?
cmd_mdio.c:144:5: warning: symbol 'extract_phy_range' was not declared. Should it
cmd_mem.c:54:5: warning: symbol 'do_mem_md' was not declared. Should it be static?
cmd_mem.c:150:5: warning: symbol 'do_mem_mm' was not declared. Should it be static?
cmd_mem.c:154:5: warning: symbol 'do_mem_nm' was not declared. Should it be static?
cmd_mem.c:159:5: warning: symbol 'do_mem_mw' was not declared. Should it be static?
cmd_mem.c:256:5: warning: symbol 'do_mem_cmp' was not declared. Should it be static?
cmd_mem.c:326:5: warning: symbol 'do_mem_cp' was not declared. Should it be static?
cmd_mem.c:436:5: warning: symbol 'do_mem_base' was not declared. Should it be static?
cmd_mem.c:449:5: warning: symbol 'do_mem_loop' was not declared. Should it be static?
cmd_mem.c:595:5: warning: symbol 'do_mem_mtest' was not declared. Should it be static?
cmd_mem.c:618:26: warning: Using plain integer as NULL pointer
cmd_mem.c:1057:5: warning: symbol 'do_mem_crc' was not declared. Should it be static?
cmd_misc.c:30:5: warning: symbol 'do_sleep' was not declared. Should it be static
cmd_mmc.c:118:5: warning: symbol 'do_mmcinfo' was not declared. Should it be static?
cmd_mmc.c:272:32: warning: Using plain integer as NULL pointer
cmd_mmc.c:150:5: warning: symbol 'do_mmcops' was not declared. Should it be stati
cmd_mp.c:27:1: warning: symbol 'cpu_cmd' was not declared. Should it be static?
cmd_mp.c:85:1: error: directive in argument list
cmd_mp.c:88:1: error: directive in argument list
cmd_mtdparts.c:150:18: warning: symbol 'mtdids' was not declared. Should it be static?
cmd_mtdparts.c:153:18: warning: symbol 'devices' was not declared. Should it be static?
cmd_mtdparts.c:713:5: warning: symbol 'mtd_device_validate' was not declared. Should it be static?
cmd_mtdparts.c:1887:5: warning: symbol 'do_chpart' was not declared. Should it be static?
cmd_mtdparts.c:1925:5: warning: symbol 'do_mtdparts' was not declared. Should it be static?
cmd_mtdparts.c:2060:1: error: directive in argument list
cmd_mtdparts.c:2063:1: error: directive in argument list
cmd_mtdparts.c:2066:1: error: directive in argument list
cmd_mtdparts.c:2071:1: error: directive in argument list
cmd_mtdparts.c:2073:1: error: directive in argument list
cmd_nand.c:377:18: error: bad constant expression
cmd_nand.c:431:5: warning: symbol 'do_nand' was not declared. Should it be static?
cmd_nand.c:796:1: error: directive in argument list
cmd_nand.c:801:1: error: directive in argument list
cmd_nand.c:802:1: error: directive in argument list
cmd_nand.c:806:1: error: directive in argument list
cmd_nand.c:819:1: error: directive in argument list
cmd_nand.c:824:1: error: directive in argument list
cmd_nand.c:825:1: error: directive in argument list
cmd_nand.c:831:1: error: directive in argument list
cmd_nand.c:918:5: warning: symbol 'do_nandboot' was not declared. Should it be static?
cmd_net.c:33:5: warning: symbol 'do_bootp' was not declared. Should it be static?
cmd_net.c:107:5: warning: symbol 'do_dhcp' was not declared. Should it be static?
cmd_net.c:120:5: warning: symbol 'do_nfs' was not declared. Should it be static?
cmd_nvedit.c:138:5: warning: symbol 'do_env_print' was not declared. Should it be static?
cmd_nvedit.c:323:5: warning: symbol '_do_env_set' was not declared. Should it be static?
cmd_nvedit.c:435:5: warning: symbol 'do_env_set' was not declared. Should it be static?
cmd_nvedit.c:514:5: warning: symbol 'do_env_edit' was not declared. Should it be static?
cmd_nvedit.c:620:5: warning: symbol 'do_env_save' was not declared. Should it be static?
cmd_nvedit.c:1016:1: error: directive in argument list
cmd_nvedit.c:1018:1: error: directive in argument list
cmd_nvedit.c:1021:1: error: directive in argument list
cmd_nvedit.c:1023:1: error: directive in argument list
cmd_nvedit.c:1024:1: error: directive in argument list
cmd_nvedit.c:1026:1: error: directive in argument list
cmd_nvedit.c:1027:1: error: directive in argument list
cmd_nvedit.c:1029:1: error: directive in argument list
cmd_nvedit.c:1030:1: error: directive in argument list
cmd_nvedit.c:1032:1: error: directive in argument list
cmd_nvedit.c:1034:1: error: directive in argument list
cmd_nvedit.c:1036:1: error: directive in argument list
cmd_nvedit.c:1037:1: error: directive in argument list
cmd_nvedit.c:1039:1: error: directive in argument list
cmd_pci.c:38:17: warning: symbol 'ShortPCIListing' was not declared. Should it be static?
cmd_pci.c:38:22: warning: 'ShortPCIListing' defined but not used [-Wunused-variable]
cmd_pci.c:411:5: warning: symbol 'do_pci' was not declared. Should it be static?
cmd_pci.c:494:1: error: directive in argument list
cmd_pci.c:497:1: error: directive in argument list
cmd_reginfo.c:40:5: warning: symbol 'do_reginfo' was not declared. Should it be static?
cmd_sata.c:31:5: warning: symbol 'sata_curr_device' was not declared. Should it be static?
note -> ata_piix.c doesn't seem to use 'sata_curr_device'; deleted.
cmd_sata.c:32:18: warning: symbol 'sata_dev_desc' was not declared. Should it be static?
cmd_sata.c:70:5: warning: symbol 'do_sata' was not declared. Should it be static?
cmd_setexpr.c:53:5: warning: symbol 'do_setexpr' was not declared. Should it be static?
cmd_source.c:186:1: error: directive in argument list
cmd_source.c:190:1: error: directive in argument list
cmd_test.c:27:5: warning: symbol 'do_test' was not declared. Should it be static?
cmd_test.c:153:5: warning: symbol 'do_false' was not declared. Should it be static?
cmd_test.c:164:5: warning: symbol 'do_true' was not declared. Should it be static
cmd_usb.c:43:6: warning: symbol 'usb_get_class_desc' was not declared. Should it be static?
cmd_usb.c:69:6: warning: symbol 'usb_display_class_sub' was not declared. Should it be static?
cmd_usb.c:151:6: warning: symbol 'usb_display_string' was not declared. Should it be static?
cmd_usb.c:161:6: warning: symbol 'usb_display_desc' was not declared. Should it be static?
cmd_usb.c:195:6: warning: symbol 'usb_display_conf_desc' was not declared. Should it be static?
cmd_usb.c:210:6: warning: symbol 'usb_display_if_desc' was not declared. Should it be static?
cmd_usb.c:227:6: warning: symbol 'usb_display_ep_desc' was not declared. Should it be static?
cmd_usb.c:252:6: warning: symbol 'usb_display_config' was not declared. Should it be static?
cmd_usb.c:283:6: warning: symbol 'usb_show_tree_graph' was not declared. Should it be static?
cmd_usb.c:343:6: warning: symbol 'usb_show_tree' was not declared. Should it be static?
cmd_usb.c:356:5: warning: symbol 'do_usbboot' was not declared. Should it be static?
cmd_usb.c:366:5: warning: symbol 'do_usb' was not declared. Should it be static?
cmd_version.c:31:5: warning: symbol 'do_version' was not declared. Should it be s
cmd_ximg.c:46:1: warning: symbol 'do_imgextract' was not declared. Should it be static?
cmd_ximg.c:272:1: error: directive in argument list
cmd_ximg.c:276:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fail in 'mmc rescan' if mmc_init() returns error
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
mmc read and write command has so many in common, unfiy those two to
force consistency across the those two.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Andy Fleming <afleming@freescale.com>
For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)
As bootloader may need to read out or reflashing images on those
different partitions, it is better to enable the partition switch with
console command support.
Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Rather than using a custom "Usage:", use the common cmd_usage() function,
and tail into it now that it returns 1 for us.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Most of the files have U_BOOT_CMD on a separate line,
but a few didn't and had the first line on the same line
as U_BOOT_CMD.
This changes these files by adding a line break and a tab
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
removed the command name from the help message as it is already printed.
for cmd_mmc also rewrote the message a little bit
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
The curr_device variable isn't used outside of cmd_mmc, so mark it static
to avoid conflicts with other pieces of code (like sata which also exports
a curr_device). Otherwise we end up with stuff like:
common/libcommon.a(cmd_sata.o):(.data.curr_device+0x0):
multiple definition of `curr_device'
common/libcommon.a(cmd_mmc.o):(.data.curr_device+0x0): first defined here
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
find_mmc_device returns NULL if an invalid device number is specified.
Check for this to avoid dereferencing NULL pointers.
Signed-off-by: Rabin Vincent <rabin@rab.in>
