I can't build test this, but just looking at the config files written
and it seems OK ...
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
For newer STM parts where CFI >= 1.1, there is a byte in the extended
structure that declares the flash layout type (just like the AMD parts),
so key off of that to find out when we need to reverse the geometry.
This can be seen with M29W640 parts where U-Boot does:
Bank # 1: CFI conformant FLASH (16 x 16) Size: 8 MB in 135 Sectors
AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22ED
Erase timeout: 8192 ms, write timeout: 1 ms
Buffer write timeout: 1 ms, buffer size: 16 bytes
Sector Start Addresses:
20000000 RO 20002000 RO 20004000 RO 20006000 RO 20008000 RO
2000A000 RO 2000C000 RO 2000E000 RO 20010000 RO 20020000 RO
...
But Linux does:
physmap platform flash device: 00800000 at 20000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank.
Manufacturer ID 0x000020 Chip ID 0x0022ed
physmap-flash.0: Swapping erase regions for top-boot CFI table.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When dealing with non-multipoint devices, if the software root hub code
accepted the message, then we still need to process it normally. So only
return quickly when the root hub skipped the message or is otherwise in
an error state.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-arm:
run arm_pci_init after relocation
IXP42x PCI rewrite
update/fix PDNB3 board
update/fix IXDP425 / IXDPG425 boards
add dvlhost (dLAN 200 AV Wireless G) board
IXP NPE: add support for fixed-speed MII ports
update/fix AcTux4 board
update/fix AcTux3 board
update/fix AcTux2 board
update/fix AcTux1 board
use -ffunction-sections / --gc-sections on IXP42x
support CONFIG_SYS_LDSCRIPT on ARM
fix "depend" target in npe directory
Fix IXP code to work after relocation was added
trigger hardware watchdog in IXP42x serial driver
add support for IXP42x Rev. B1 and newer
add XScale sub architecture (IXP/PXA) to maintainer list
Conflicts:
arch/arm/lib/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
clean up IXP PCI handling: get rid of IXP-private bus scan, BAR assign etc.
code and use u-boot's PCI infrastructure instead. Move board-specific PCI
setup code (clock/reset) to board directory.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
- jump to real flash location after reset before turning off flash mirror
- fix timer system to use HZ == 1000, remove broken interrupt-based code
Signed-off-by: Michael Schwingen <michael@schwingen.org>
On Sunday, June 19, 2011 13:55:13 Ilya Yanok wrote:
> On 18.06.2011 23:03, Mike Frysinger wrote:
> >> - tools/Makefile put common/env_embedded.o and envcrc.o to object list
> >>
> >> conditionally. This fixes errors during dependency generation.
> >
> > pretty sure this breaks board builds. if the only thing this fixes is a
>
> I'm sorry but I can't see how this can break the builds. Could you
> please be more specific? I've tried to build some boards, it actually
> works...
i might be thinking of a different env_embedded situation. a different
problem with your patch to tools/Makefile: you copied the same logic multiple
times which means more bitrot.
why dont you do something like:
> > harmless warning when generating dependency files, then i say ignore it.
> > after all, this is how it has always worked in the past and no one really
> > cared.
>
> Yep, they are harmless but they are not warnings but rather scary errors
> actually. ;) I think it's better to fix them.
i guess my threshold for being scared is a bit higher :p
-mike
mkimage relies on autogenerated version so we need to move
$(VERSION_FILE) rule out of ifeq and make tools rule depend on it to be
able to run 'make tools' from the unconfigured tree.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
LDSCRIPT is used only from the top-level Makefile and only when the
system is configured so we can move LDSCRIPT and CONFIG_SYS_LDSCRIPT
related logic into the top level Makefile and under configured condition
to avoid errors when building tools from unconfigured tree.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it. Drop it.
This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes following compile warning:
---8<---
macb.c: In function 'macb_write_hwaddr':
macb.c:525:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
This patch removes the warning
---8<---
at91_emac.c: In function 'at91emac_write_hwaddr':
at91_emac.c:487:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
The rework effort for ATMEL (AT91/AVR32) accidentially broke build of
this driver. Fix this to make it build again. However this driver should
be reworked as soon as possible!
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
* Fix: timer.c compile error io.h not found with arm/at91rm9200
* update arm920t/at91 to ATMEL_xxx name scheme
* update arm920t/at91 soc lib
* update at91_emac driver
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
