With commit 6900797678 ("cros_ec: Support keyboard scanning with
EC_CMD_GET_NEXT_EVENT") check_for_keys() tries to read keyboard
strokes using EC_CMD_GET_NEXT_EVENT. But the sandbox driver does
not understand this command. We need to reply with
-EC_RES_INVALID_COMMAND to force check_for_keys() to fall back to
use EC_CMD_MKBP_STATE. Currently the driver prints
** Unknown EC command 0x67
in this case. With the patch the message is suppressed.
In a future patch we should upgrade the sandbox driver to provide
EC_CMD_GET_NEXT_EVENT support.
Fixes: 6900797678 ("cros_ec: Support keyboard scanning with EC_CMD_GET_NEXT_EVENT")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Erasing the flash can take over a second on some devices and the EC is
not responsive during this time. Update the timeout to 5 seconds to cope
with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The EC now requires that the offset field be set correctly when checking
on hash status. Update the code to handle this. Use the same message
struct in both functions to reduce stack space.
Signed-off-by: Simon Glass <sjg@chromium.org>
The following bugs are fixed:
* The conitrace command failed to build.
* Non-volatile UEFI variables were not delete form the file store.
The following features are added:
* Support for the FN1 - FN10 keys on crosswire keyboards is added.
* An EFI binary is provided to dump the binary device tree.
tpm2_get_capability() is adjusted in preparation of the implementation
of the EFI_TCG2_PROTOCOL.
-----BEGIN PGP SIGNATURE-----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=swsS
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc2-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc2 (2)
The following bugs are fixed:
* The conitrace command failed to build.
* Non-volatile UEFI variables were not delete form the file store.
The following features are added:
* Support for the FN1 - FN10 keys on crosswire keyboards is added.
* An EFI binary is provided to dump the binary device tree.
tpm2_get_capability() is adjusted in preparation of the implementation
of the EFI_TCG2_PROTOCOL.
In case there is an EEPROM attached to the KS8851 MAC and the EEPROM
contains a valid MAC address, the MAC address is loaded into the NIC
registers on power on. Read the MAC address out of the NIC registers
and provide it to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Chromebooks and the sandbox use a crosswire keyboard with function keys
FN1 - FN10. These keys are needed when running UEFI applications like GRUB
or the UEFI SCT.
Add support for these keys when translating from key codes to
ECMA-48 (or withdrawn ANSI 3.64) escape sequences.
All escape sequences start with 0x1b. So we should not repeat this
byte in the kbd_to_ansi364 table.
For testing use:
sandbox_defconfig + CONFIG_EFI_SELFTEST=y
$ ./u-boot -D -l
=> setenv efi_selftest extended text input
=> bootefi selftest
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl+kJL8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaDpAf+MajyuxlmGmFTjpyiB026aWiYE4rAn4AE
bXEDxHpOTIH4hDX7kYVWPmuKivHJo2hF0WUpIFBEAgtc2dOfjOP+mrDjBzG1Pikl
z5yuilG7eHwC1kTIkPv/tPHwDWRBI5VNwTYq0VTtffMKr8LCBo96wEYEbeYK0xdQ
kpNa9d4G+tpx20BCRgPLeOMk2pg5SVszkCCkmmPd12rO2zJ9+wWa8fwA759E93Rw
RshoRCtLNo2nEA3uJVG2aN9n3eAdM/iupDVdBLg50SFKabUxt7OcvGOC8NzGdAmT
9UbB8scvQJyI/kylGT+ghH3o2RqQGvuIRXmDyETckdkpiqK0SQvysg==
=eOGz
-----END PGP SIGNATURE-----
Merge tag 'dm-pull5nov20' of git://git.denx.de/u-boot-dm
patman status subcommand to collect tags from Patchwork
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Some boards want to specify the manufacturer or product name but do not
need to have their own sysinfo driver.
Add a default driver which provides a way to specify this SMBIOS
information in the devicetree, without needing any board-specific
functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This does not necessarily indicate a problem, since some pins are
optional. Let the caller show an error if necessary.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if SSDT and DSDT code is created, only the latter is retained
for examination by the 'acpi items' command. Fix this by only resetting
the list when explicitly requested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A few functions have changed to return pin numbers or I2C addresses. The
error checking for some of the callers is therefore wrong. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCX6QsVQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76Z29ACfRdzFocIVEOFNm8v5yA1C/FU9q9sAn1kEAot5
vkm2yvDQ7+9vl5G7+ZRn
=rCCX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20201105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx for 2021.1
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
The cros_ec_keyb driver currently uses EC_CMD_MKBP_STATE to scan the
keyboard, but this host command was superseded by EC_CMD_GET_NEXT_EVENT
and unavailable on more recent devices (including gru-kevin), as it was
removed in cros-ec commit 87a071941b89 ("mkbp: Add support for buttons
and switches.") dated 2016-07-06.
The EC_CMD_GET_NEXT_EVENT has been available since cros-ec commit
d1ed75815efe ("MKBP event signalling implementation") dated 2014-10-20,
but it looks like it isn't included in firmware-* branches for at least
link, nyan-big, samus, snow, spring, panther and peach-pit which have
defconfigs in U-Boot. So this patch falls back to the old method if the
EC doesn't recognize the newer command.
The implementation is mostly adapted from Depthcharge commit
f88af26b44fc ("cros_ec: Change keyboard scanning method.").
On a gru-kevin, the current driver before this patch fails to read the
pressed keys with:
out: cmd=0x60: 03 9d 60 00 00 00 00 00
in-header: 03 fc 01 00 00 00 00 00
in-data:
ec_command_inptr: len=-1, din=0000000000000000
check_for_keys: keyboard scan failed
However the keyboard works fine with the newer command:
out: cmd=0x67: 03 96 67 00 00 00 00 00
in-header: 03 ef 00 00 0e 00 00 00
in-data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ec_command_inptr: len=14, din=00000000f412df30
key_matrix_decode: num_keys = 0
0 valid keycodes found
out: cmd=0x67: 03 96 67 00 00 00 00 00
in-header: 03 df 00 00 0e 00 00 00
in-data: 00 00 00 00 00 00 00 00 00 00 00 00 10 00
ec_command_inptr: len=14, din=00000000f412df30
key_matrix_decode: num_keys = 1
valid=1, row=4, col=11
keycode=28
1 valid keycodes found
{0d}
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Up to now the sandbox would shutdown upon a cold reset request. Instead it
should be reset.
In our coding we use static variables like LIST_HEAD(efi_obj_list). A reset
can occur at any time, e.g. via an UEFI binary calling the reset service.
The only safe way to return to an initial state is to relaunch the U-Boot
binary.
The reset implementation uses execv() to relaunch U-Boot.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there are a lot of dtoc warnings reported when building
chromebook_coral, of the form:
WARNING: the driver intel_apl_lpc was not found in the driver list
Correct these by using driver names that matches their compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix the dtoc warning in these file by using a driver name that matches the
compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The series contains the following enhancements
* preparatory patches for UEFI capsule updates
* initialization of the emulated RTC using an environment variable
and a bug fix
* If DisconnectController() is called for a child controller that is the
only child of the driver, the driver must be disconnected.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl+e1WUACgkQxIHbvCwF
GsRHhQ//X/hQiow1/3YwskyZkC89QPLE+TDeGcRHdy7W2rjfJlOBJtsI1tzvsTWw
8etgIuoh1MKebJZZQk/ZxKdWOaN3RWP7wL/9c6PHpkkML+WzyLWShf5UgLMWeo3w
a7t0LW4kfxbzmhg/f4x0Gi3qUh0SiS6T8Q5X/SlJOX091IvCmCOTkGUT6dBogm78
WnISQvgP3uApOt2s66hVVtFaH4zbXDYwDnQhhUoonRF1AfuE3jTyr39IoNsCdPOx
vEbTqNKQQnt4yIIaPJlV+KX//jtCCnyLBPrZA1tI2QPyBjADmNcau2OjlBZyJpr0
1awgSueXgBtMCAp6bHMl9p3eSKYv2f0BvPGljgKrs9dfIZk+XN0w62VuSYwRi7TU
ZEppINMisM1hC9+7jKNGn0nE9y3UldBSNThWxk8ykpWL+Btv5KeArHK4+916nadQ
a7t+6Ow7hiVI1Y/3TWaLvCi7xfqsU87QH6dx0nozgBUotuujIqa5lAeSGR9Rc6N2
PSblEGf8AA8+oGAdBhNvDncHiRLWkUoBqFsaaAk4EiaHQk60InZ9CpQdeMqHErcx
uLL9JcOCZeStcWF+vWmyU2L49O88HRHvboM7zA+gqLIUilwgKxmlOocoq+0jtA4l
Bg72F3cI7+g+aTidskEOGo2v2cj0dh32ub5CqRHLdt3PUzP6qhs=
=mCEL
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc2 (2)
The series contains the following enhancements
* preparatory patches for UEFI capsule updates
* initialization of the emulated RTC using an environment variable
and a bug fix
* If DisconnectController() is called for a child controller that is the
only child of the driver, the driver must be disconnected.
Add GPIO poweroff driver, which is based on the Linux
driver and uses the same DT binding.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In case of empty battery or glitches the oscillator fail
bit might be set. This will reset the bit in the reset
routine.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This takes care of resetting the 32kHz square wave, which is
used by some boards as clock source for the SoC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver allows to use SPI flash as backing store for
boot counter values with DM enabled.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This option is only supported by the IMX watchdog and seems to be
similar to CONFIG_WATCHDOG.
Move it below the IMX watchdog and make it dependent on IMX_WATCHDOG.
Signed-off-by: Michael Walle <michael@walle.cc>
commit c05ed00afb dropped linux/delay.h from common header
add linux/delay.h to avoid compile warning here
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
Like, rk3399 the rk3288 also supports 4K resolution.
So, enable it for rk3288 with HDMI platforms.
Right now, rockchip video drivers are supporting for rk3288,
rk3399 SoC families, so mark the 4K resolution by default
if it's an HDMI video out.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This function is a variant of dfu_write_by_name() and takes a DFU alt
setting number for dfu configuration.
It will be utilised to implement UEFI capsule management protocol for
raw image in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This variable will be utilized to enumerate all dfu entities
for UEFI capsule firmware update in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The main purpose of this patch is to separate a generic interface for
updating firmware using DFU drivers from "auto-update" via tftp.
This function will also be used in implementing UEFI capsule update
in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The range of an addressable pointer can go beyond 'integer'.
So change the argument type to a void pointer.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is essentially independent from tftp, and will also be
utilised in implementing UEFI capsule update in a later commit.
So just give it a more generic name.
In addition, a new configuration option, CONFIG_DFU_WRITE_ALT, was
introduced so that the file will be compiled with different options,
particularly one added in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Up to now the emulated RTC is initialized using the U-Boot build time.
With this patch the environment variable 'rtc_emul_epoch' can be used to
provide a better initial time. The variable is a decimal string with
the number of seconds since 1970-01-01. Here is an example where the RTC
had not been probed yet:
=> setenv rtc_emul_epoch 1610109000
=> date
Date: 2021-01-08 (Friday) Time: 12:30:00
If the variable does not exist, the U-Boot build time is used as fallback.
The environment variable may be set when shutting down the operating system
if the U-Boot environment is exposed to the OS (cf. ENV_IS_IN_FAT and
ENV_IS_IN_EXT4).
Suggested-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently the emulated RTC is initialized in the emul_rtc_get() get
function. This does not match the design of the driver model.
Move the initialization of the emulated RTC to the probe() function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Found this by comparing it to the coreboot driver, a form of this call
was introduced there in their commit b9a7877568cf ("rockchip/*: refactor
edp driver"). This is copy-pasted from U-Boot's link_train_cr() slightly
above it.
Without this on a gru-kevin chromebook, I have:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
channel eq failed, ret=-5
link train failed!
rk_vop_probe() Device failed: ret=-5
With this, it looks like training succeeds:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 6dB
using signal parameters: voltage 0.4V pre_emph 6dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 0dB
using signal parameters: voltage 0.4V pre_emph 0dB
channel eq at voltage 0 pre-emphasis 0
config video failed
rk_vop_probe() Device failed: ret=-110
The "config video failed" error also goes away when I disable higher
log levels, and it claims to have successfully probed the device.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The SRAM on the PX30 is not big enough to hold multiple DDR configs
so it needs to be selected during build.
So far simply the DDR3 config was always selected and getting DDR4
or LPDDR2/3 initialized would require a code modification.
So add Kconfig options similar to RK3399 to allow selecting the DDR4
and LPDDR2/3 options instead, while DDR3 stays the default as before.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
In order to correctly calculate the designware watchdog
timeouts, the watchdog clock is required. Implement required
clocks to facilitate this.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
At present we use a 'node' pointer in the of-platadata phandle_n_arg
structs. This is a pointer to the struct driver_info for a particular
device, and we can use it to obtain the struct udevice pointer itself.
Since we don't know the struct udevice pointer until it is allocated in
memory, we have to fix up the phandle_n_arg.node at runtime. This is
annoying since it requires that SPL's data is writable and adds a small
amount of extra (generated) code in the dm_populate_phandle_data()
function.
Now that we can find a driver_info by its index, it is easier to put the
index in the phandle_n_arg structures.
Update dtoc to do this, add a new device_get_by_driver_info_idx() to look
up a device by drive_info index and update the tests to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that parent devices are supported with of-platadata, we don't need the
messy code to fix up the parent pointers and allocations on Apollo Lake.
Put the code behind a condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, enabling CONFIG_APL_SPI_FLASH_BOOT does not build since SPI
and SPI flash are not enabled for TPL. Add a condition to fix this and
tidy up a build warning in the SPI-flash driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple test that we can obtain the correct parent for an I2C
device. This requires updating the driver names to match the compatible
strings, adding them to the devicetree and enabling a few options.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present of-platdata does not provide parent information. But this is
useful for I2C devices, for example, since it allows them to determine
which bus they are on.
Add support for setting the parent correctly, by storing the parent
driver_info index in dtoc and reading this in lists_bind_drivers(). This
needs multiple passes since we must process children after their parents
already have been bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no devicetree with of-platdata. Update a few uclasses to allow
them to be built for sandbox_spl. Also drop the i2c-gpio from SPL to avoid
build errors, since it does not support of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we update the driver_info struct with a pointer to the device
that it created (i.e. caused to be bound). This works fine when U-Boot SPL
is stored in read-write memory. But on some platforms, such as Intel
Apollo Lake, it is not possible to update the data memory.
In any case, it is bad form to put this information in a structure that is
in the data region, since it expands the size of the binary.
Create a new driver_rt structure which holds runtime information about
drivers. Update the code to store the device pointer in this instead.
Also update the test check that this works.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a test in dtoc for this feature, but not one in U-Boot itself.
Add a simple test that checks that the information comes through
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
With of-platdata, the driver_info struct is updated with the device
pointer when it is bound. This makes it easy for a device to be found by
its driver info with the device_get_by_driver_info() function.
Add a test that all devices (except the root device) have such an entry.
Fix a bug that the function does not set *devp to NULL on failure, which
the documentation asserts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option is disabled in SPL, meaning that warnings are not
displayed. It is sometimes useful to see warnings in SPL for debugging
purposes.
Add a new Kconfig option to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
