Commit graph

28170 commits

Author SHA1 Message Date
Paul Burton
a3bdaacaf6 malta: enable HUSH parser
The malta board is used for development and thus the shell is interacted
with often. Enable HUSH to make the experience a little more pleasant.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 13:11:02 +01:00
Paul Burton
28c8c3d40f malta: delay after reset
Reset isn't instant, so delay to give it a chance. Otherwise we go on
to print a failure message before resetting anyway.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 13:11:02 +01:00
Paul Burton
ba21a453a5 malta: IDE support
This patch adds IDE support to the MIPS Malta board. The IDE controller
is enabled after probing the PCI bus and otherwise just makes use of
U-boot generic IDE support.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 13:11:02 +01:00
Paul Burton
8755d50706 MIPS: clear TagLo select 2 during cache init
Current MIPS cores from Imagination Technologies use TagLo select 2 for
the data cache. The architecture requires that it is safe for software
to write to this register even if it isn't present, so take the trivial
option of clearing both selects 0 & 2.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
dd7c72006e MIPS: allow systems to skip loads during cache init
Current MIPS systems do not require that loads be performed to force the
parity of cache lines, a simple invalidate by clearing the tag for each
line will suffice. Thus this patch makes the loads & subsequent second
invalidation conditional upon the CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
option, and defines that for existing mips32 targets. Exceptions are
malta where this is known to be unnecessary, and qemu-mips where caches
are not implemented.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
ca4e833cd6 MIPS: inline mips_init_[id]cache functions
The mips_init_[id]cache functions are small & only called once from a
single callsite. Inlining them allows mips_cache_reset to avoid having
to bother moving arguments around & leaves it a leaf function which is
thus able to simply keep the return address live in the ra register
throughout, simplifying the code.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
ac22feca11 MIPS: refactor cache loops to a macro
Reduce duplication by performing loops through cache tags using an
assembler macro.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
536cb7ce1a MIPS: refactor L1 cache config reads to a macro
Reduce duplication between reading the configuration of the L1 dcache &
icache by performing both using a macro which calculates the appropriate
line & cache sizes from the coprocessor 0 Config1 register.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
4a5d8898bc MIPS: unify cache initialization code
The mips32 & mips64 cache initialization code differs only in that the
mips32 code supports reading the cache size from coprocessor 0 registers
at runtime. Move the more developed mips32 version to a common
arch/mips/lib/cache_init.S & remove the now-redundant mips64 version in
order to reduce duplication. The temporary registers used are shuffled
slightly in order to work for both mips32 & mips64 builds. The RA
register is defined differently to suit mips32 & mips64, but will be
removed by a later commit in the series after further cleanup.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
30374f98d1 MIPS: unify cache maintenance functions
Move the more developed mips32 version of the cache maintenance
functions to a common arch/mips/lib/cache.c, in order to reduce
duplication between mips32 & mips64.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:00 +01:00
Paul Burton
2b8bcc5a2f MIPS: avoid .set ISA for cache operations
As a step towards unifying the cache maintenance code for mips32 &
mips64 CPUs, stop using ".set <ISA>" directives in the more developed
mips32 version of the code. Instead, when present make use of the GCC
builtin for emitting a cache instruction. When not present, simply don't
bother with the .set directives since U-boot always builds with
-march=mips32 or higher anyway.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:00 +01:00
Tom Rini
ab92da9f47 Merge branch 'master' of git://git.denx.de/u-boot-x86 2015-01-26 17:44:49 -05:00
Tom Rini
aed03faa06 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-01-26 06:42:40 -05:00
Tom Rini
306df2c824 Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze 2015-01-26 06:42:15 -05:00
Michal Simek
a2425e6207 serial: Extend structure comments with register offset
This information help with debugging issues with uart.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:59 +01:00
Michal Simek
12c9e7d622 serial: zynq: Use global baudrate instead of hardcoded one
This change enables to change baudrate on command line.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:58 +01:00
Siva Durga Prasad Paladugu
c4fa511425 ARM: zynq: Add USB lthor download protocol support
updated the zynq config to support the lthor
download protocol.
This lthor functionality helps us to load linux
images on to DDR/MMC and can boot linux using bootm.
In order to load images the user should run lthor
command run "thor_ram" from u-boot prompt and
then send the images from host using lthor utility.

Define g_dnl_bind_fixup for zynq so that correct vendor
and product ids assigned incase of DFU and lthor.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:58 +01:00
Siva Durga Prasad Paladugu
87f3dbdffc ARM: zynq: Enable DFU functionality in zynq
Enable DFU functionality in zynq.
This DFU functionality helps us to load linux
images on to DDR and can boot linux using bootm.
In order to load images the user should run dfu
command "dfu 0 ram 0" from u-boot prompt and then
send the images from host.

The malloc size has been increased to match the DFU
buffer requirements.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:58 +01:00
Siva Durga Prasad Paladugu
f20b37f353 ARM: zynq: provide config option to select emio
Dont send always emio value as zero for zynq_gem_initialize
send it based on config.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:58 +01:00
Michal Simek
dd1c351ffe ARM: zynq: Group ethernet configuration options together
No functional chagnes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:58 +01:00
Michal Simek
e9d69c1c71 ARM: zynq: Use CMD_FS_GENERIC
Based on:
"am335x_evm: Enable CMD_EXT4 and CMD_FS_GENERIC, add bootpart to env"
(sha1: 73a27a84e5)

Fix filesystem specific commands for loading.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:58 +01:00
Michal Simek
5a82d53c78 ARM: zynq: Show board information by default
Show board information in bootlog and enable it by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
c8eac66bae ARM: zynq: List qspi, smc and nand baseaddresses
Add missing addresses to the list.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
63e3cea515 ARM: zynq: List nand, qspi and jtag boot modes
Use full boot mode list in SPL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Siva Durga Prasad Paladugu
f60c6fbbc6 ARM: zynq: slcr: Dont modify the reserved bits
Set only the 0-3 bits of the FPGA_RST_CTRL register
as other bits should not be set to 1.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
3ad87ca182 ARM: zynq: ddrc: Setup half of memory only for ECC case
Setup half of memory from ram_size for ECC case.
All the time the same board can be configured
with or without ECC. Based on ECC case detection
use half of memory with the same configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
555c7c066f ARM: zynq: Remove empty line
Trivial patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:57 +01:00
Michal Simek
c08cfc2d2c ARM: zynq: Enable the Neon instructions
Added the lowlevel_init to enable the Neon instructions.

Initially the u-boot was causing undefined instruction
exception if loaded through tcl, and working fine if loaded
through FSBL. The exception was causing in convertion formula
of given time to ticks. It was because, the Neon instructions
were disabled and hence causing the undefined exception. In
FSBL case, the FSBL was enabling the Neon instructions. Hence,
added the lowlevel_init to enable the Neon instructions.

Also enable neon instructions for non-xilinx toolchain.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-26 08:55:31 +01:00
Tom Rini
03cae7261e Merge branch 'master' of git://git.denx.de/u-boot-marvell 2015-01-25 19:05:40 -05:00
Gerald Kerma
361b3d8613 marvell: kirkwood: guruplug refresh for newer kernel
Refresh for newer kernel.
Prepare ENV settings for sheevaplugs to be OpenWRT ready.

    +----------+
    | UBOOT    | >> 896 Kb (7x128)  = uboot
    +----------+
    | ENV      | >> 128 Kb          = uboot_env
    +----------+
    | ROOT(FS) | >> 511 Mb @ 1 Mb   = root -> rootfs (ubifs)
    +----------+

With (CC) TRUNK OpenWRT build (QUICK HOWTO) :

    <INTERRUPT>
    Marvell>> nand erase.part root
    Marvell>> ubi part root
    Marvell>> ubi remove rootfs
    Marvell>> ubi create rootfs
    Marvell>> usb reset
    Marvell>> fatload usb 2:1 0x800000 guruplug/openwrt/openwrt-kirkwood-guruplug-rootfs.ubifs
    Marvell>> ubi write 0x800000 rootfs ${filesize}
    Marvell>> reset

Changes in v1:
- ADD generic board define
- ADD FDT support
- ADD HUSH interpreter
- Define new NAND partition mapping

Signed-off-by: Gerald Kerma <dreagle@doukki.net>
2015-01-26 00:25:29 +01:00
Luka Perkov
d4d8f1b726 kirkwood: sheevaplug: add CONFIG_SYS_GENERIC_BOARD define
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:16 +01:00
Luka Perkov
604a0dd64e kirkwood: pogo_e02: add CONFIG_SYS_GENERIC_BOARD define
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:16 +01:00
Luka Perkov
92ca8bda41 kirkwood: iconnect: add CONFIG_SYS_GENERIC_BOARD define
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:16 +01:00
Luka Perkov
15155b49ad kirkwood: goflexhome: add CONFIG_SYS_GENERIC_BOARD define
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:16 +01:00
Luka Perkov
6054b153a5 kirkwood: dockstar: add CONFIG_SYS_GENERIC_BOARD define
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:16 +01:00
Luka Perkov
c147ff9df1 kirkwood: ib62x0: add CONFIG_SYS_GENERIC_BOARD define
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
CC: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:16 +01:00
Luka Perkov
62d1e990d9 ARM: kirkwood: fix cpu info for 6282 device id
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Stefan Roese <sr@denx.de>
2015-01-25 23:56:15 +01:00
Luka Perkov
5aa2297da7 kirkwood: define empty CONFIG_MVGBE_PORTS by default
Each board with defines it's own set of values. If we do not define
CONFIG_MVGBE_PORTS we will hit following error:

mvgbe.c: In function 'mvgbe_initialize':
mvgbe.c:700:34: error: 'CONFIG_MVGBE_PORTS' undeclared (first use in this function)
  u8 used_ports[MAX_MVGBE_DEVS] = CONFIG_MVGBE_PORTS;

This patch fixes above described problem.

Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2015-01-25 23:56:15 +01:00
Luka Perkov
49413ea3f5 cosmetic: kirkwood: style fixes in kwbimage.cfg files
When diffing through the changes only the relevant changes
should be displayed.

Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
2015-01-25 23:56:09 +01:00
tang yuantian
41ba57d0c7 fsl/ls1021qds: Add deep sleep support
Add deep sleep support on Freescale LS1021QDS platform.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-24 09:12:32 -06:00
Simon Glass
e43ade3749 x86: config: chromebook_link: Enable environment
Enable an environment area.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-01-24 06:13:46 -07:00
Simon Glass
380ab5cc27 x86: ivybridge: Drop the Kconfig MRC cache information
This is now stored in the device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:46 -07:00
Simon Glass
069f5481ba x86: config: Enable hook for saving MRC configuration
Add a hook to ensure that this information is saved.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-01-24 06:13:45 -07:00
Simon Glass
191c008a21 x86: Implement a cache for Memory Reference Code parameters
The memory reference code takes a very long time to 'train' its SDRAM
interface, around half a second. To avoid this delay on every boot we can
store the parameters from the last training sessions to speed up the next.

Add an implementation of this, storing the training data in CMOS RAM and
SPI flash.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:45 -07:00
Simon Glass
a9aff2f46a x86: dts: Add SPI flash MRC details for chromebook_link
Correct the SPI flash compatible string, add an alias and specify the
position of the MRC cache, used to store SDRAM training settings for the
Memory Reference Code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:45 -07:00
Simon Glass
146251f87e Allow architecture-specific memory reservation
All memory to be reserved for use after relocation by adding a new call
to perform this reservation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:45 -07:00
Simon Glass
8e899af059 x86: spi: Add device tree support
As a temporary measure before the ICH driver moves over to driver model,
add device tree support to the driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:45 -07:00
Simon Glass
fc4860c089 x86: rtc: mc146818: Add helpers to read/write CMOS RAM
On x86 we use CMOS RAM to read and write some settings. Add basic support
for this, including access to registers 128-255.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:44 -07:00
Simon Glass
b18c68d891 x86: Use ipchecksum from net/
The existing IP checksum function is only accessible to the 'coreboot' cpu.
Drop it in favour of the new code in the network subsystem.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-24 06:13:44 -07:00
Simon Glass
9b0e35cb48 net: Add a separate file for IP checksumming
Move the checksum code out into its own file so it can be used elsewhere.
Also use a new version which supports a length which is not a multiple of
2 and add a new function to add two checksums.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-23 21:44:59 -07:00