Commit graph

19 commits

Author SHA1 Message Date
Masahiro Yamada
00aa453ebf ARM: uniphier: remove sLD3 SoC support
This SoC is too old.  It is difficult to maintain any longer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Masahiro Yamada
ee8d037ce7 ARM: uniphier: remove SPL support for ARMv8 SoCs
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family.  U-Boot SPL was intended as a temporary loader that runs in
secure world.  It is a maintenance headache to support two different
boot mechanisms.  Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-07-26 22:27:15 +09:00
Masahiro Yamada
81afa9c9a3 ARM: uniphier: add more init code for PXs3
Add the boot device table and reset deassertion for eMMC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:56:17 +09:00
Masahiro Yamada
c21f58548c ARM: uniphier: deassert RST_n of eMMC device for LD11/LD20
For LD11 and LD20 SoCs, the RST_n pin is asserted by default.  If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.

Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now.  This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Masahiro Yamada
2c2ab3d495 ARM: uniphier: add PXs3 SoC support
Initial support for PXs3 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 16:49:34 +09:00
Masahiro Yamada
a8e6300d48 ARM: uniphier: refactor spl_init_board()
Merge init-*.c into a single file using a table of callbacks because
the initialization flow is almost common among SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18 01:22:30 +09:00
Masahiro Yamada
b61664e230 ARM: uniphier: refactor board_init()
The code here is cluttered due to the switch statement.  Introduce a
table of callbacks to clean up the initialization code across SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18 01:22:30 +09:00
Masahiro Yamada
78c627cf1f ARM: uniphier: split out UMC clock enable
The clock enable bits for UMC are more SoC-specific than for
the other hardware blocks.  Separate the UMC clocks and the other
clocks for better code reuse across SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17 09:00:40 +09:00
Masahiro Yamada
c72f4d4c2e ARM: uniphier: add PLL init code for LD11 SoC
- Initialize PLLs (SPL initializes only DPLL to save the precious
   SPL memory footprint)
 - Adjust CPLL/MPLL to the final tape-out frequency
 - Set the Cortex-A53 clock to the maximum frequency since it is
   running at 500MHz (SPLL/4) on startup

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-23 01:00:23 +09:00
Masahiro Yamada
682e09ff9f ARM: uniphier: add PLL init code for LD20 SoC
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper.  Split the common code into pll-base-ld20.c for easier
re-use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:12:26 +09:00
Masahiro Yamada
fcc238baee ARM: uniphier: collect clock/PLL init code into a single directory
Now PLLs for DRAM controller are initialized in SPL, and the others
in U-Boot proper.  Setting up all of them in a single directory will
be helpful when we want to share code between SPL and U-Boot proper.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:06:47 +09:00
Masahiro Yamada
6a3e4274e4 ARM: uniphier: move PLL init code to U-Boot proper where possible
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper.  Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:06:44 +09:00
Masahiro Yamada
667dbcd01d ARM: uniphier: add PH1-LD11 SoC support
This is a low-cost ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-26 00:37:13 +09:00
Masahiro Yamada
9d0c2ceb35 ARM: uniphier: add PH1-LD20 SoC support
This is the first ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:54:08 +09:00
Masahiro Yamada
ea65c98050 ARM: uniphier: drop PH1- prefix from CONFIG options and file names
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long.  It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family.  Also, rename files for consistency.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:42:13 +09:00
Tom Rini
da58dec866 Various Makefiles: Add SPDX-License-Identifier tags
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one.  This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:19:52 -05:00
Masahiro Yamada
019df879a9 ARM: uniphier: add ProXstream2 and PH1-LD6b support
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25 00:59:33 +09:00
Masahiro Yamada
28f40d4a4d ARM: uniphier: add PH1-Pro5 support
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25 00:59:28 +09:00
Masahiro Yamada
323d1f9d5b ARM: uniphier: allow to enable multiple SoCs
Before this commit, the Kconfig menu in mach-uniphier only allowed us
to choose one SoC to be compiled.  Each SoC has its own defconfig file
for the build-test coverage.  Consequently, some defconfig files are
duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and
CONFIG_{SOC_NAME}=y.

Now, most of board-specific parameters have been moved to device trees,
so it makes sense to include init code of multiple SoCs into a single
image as long as the SoCs have similar architecture.  In fact, some
SoCs of UniPhier family are very similar:
 - PH1-LD4 and PH1-sLD8
 - PH1-LD6b and ProXstream2 (will be added in the upcoming commit)

This commit will be helpful to merge some defconfig files for better
maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25 00:58:38 +09:00