Add a basic CPU driver that retrieves information about the microblaze CPU
core. cpu_ops handlers are implemented so that the "cpu" command can work
properly:
U-Boot-mONStR> cpu list
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
U-Boot-mONStR> cpu detail
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
ID = 0, freq = 50 MHz: L1 cache, MMU
Note: cpu_ver_lookup[] and family_string_lookup[] arrays were imported from
linux.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-14-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Relocate cpu_ops pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled.
The (gd->flags & GD_FLG_RELOC) check was added to make sure the reloc_done
logic works for drivers that use DM_FLAG_PRE_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
It looks quite weird that for non PPC platforms cpu driver for MPC83xx can
be selected. That's why define proper dependency.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The cpu nodes in arch/sandbox/dts/test.dts should conform to the devicetree
specification:
* property device_type must be set to "cpu"
* the reg property must be provided
* the cpu nodes must have an address
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The crystal, CPU and master clock were not displayed correctly on SAM9X60
after adding CCF clock support. Add compatible for ARM926EJ-S to fix
this.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
To test this function, sandbox CPU must set cpu_platdata.timebase_freq on
bind. It also needs to expose a method to set the current cpu. I also make
some most members of cpu_sandbox_ops static.
On the timer side, the device tree property
sandbox,timebase-frequency-fallback controls whether sandbox_timer_probe
falls back to time_timebase_fallback or to SANDBOX_TIMER_RATE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
All cpu cores within FU540-C000 having split I/D caches.
Set the L1 cache feature bit using the i-cache-size or d-cache-size
as one of the property from device tree indicating that L1 cache is
present on the cpu core.
=> cpu detail
1: cpu@1 rv64imafdc
ID = 1, freq = 999.100 MHz: L1 cache, MMU
2: cpu@2 rv64imafdc
ID = 2, freq = 999.100 MHz: L1 cache, MMU
3: cpu@3 rv64imafdc
ID = 3, freq = 999.100 MHz: L1 cache, MMU
4: cpu@4 rv64imafdc
ID = 4, freq = 999.100 MHz: L1 cache, MMU
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The conditional check to read "mmu-type" from the device tree
is not rightly handled due to which the cpu feature doesn't include
CPU_FEAT_MMU even if it's corresponding entry is present in the device
tree.
The initialization of cpu features is now taken care in cpu-uclass
driver, so no need to zero out cpu_freq in riscv_cpu driver and can be
removed.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The cmd "cpu detail" fetches uninitialized cpu feature information
and thus displays wrong / inconsitent details as below.
For eg: FU540-C000 doesn't have any microcode, yet the cmd display's it.
=> cpu detail
1: cpu@1 rv64imafdc
ID = 1, freq = 999.100 MHz: L1 cache, MMU, Microcode, Device ID
Microcode version 0x0
Device ID 0x0
2: cpu@2 rv64imafdc
ID = 2, freq = 999.100 MHz: L1 cache, MMU, Microcode, Device ID
Microcode version 0x0
Device ID 0x0
3: cpu@3 rv64imafdc
ID = 3, freq = 999.100 MHz: L1 cache, MMU, Microcode, Device ID
Microcode version 0x0
Device ID 0x0
4: cpu@4 rv64imafdc
ID = 4, freq = 999.100 MHz: L1 cache, MMU, Microcode, Device ID
Microcode version 0x0
Device ID 0x0
The L1 cache or MMU entry seen above is also displayed inconsistently.
So initialize cpu information to zero into cpu-uclass itself so that
similar issues can be avoided for other CPU drivers.
We now see correct features as:
=> cpu detail
1: cpu@1 rv64imafdc
ID = 1, freq = 999.100 MHz
2: cpu@2 rv64imafdc
ID = 2, freq = 999.100 MHz
3: cpu@3 rv64imafdc
ID = 3, freq = 999.100 MHz
4: cpu@4 rv64imafdc
ID = 4, freq = 999.100 MHz
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The cpu clock is probably already enabled if we are executing code (though
we could be executing from a different core). This patch prevents the cpu
clock or its parents from being disabled.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Instead of always using the "clock-frequency" property to determine cpu
frequency, try using a clock in "clocks" if it exists. This patch also
fixes a bug where there could be spurious higher frequencies if sizeof(u32)
!= sizeof(ulong).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This fixes getting DT alert and critical pdata values in imx_scu_thermal
driver. On i.MX8QXP using not initialized alert pdata value resulted in
boot hang and endless loop outputting:
CPU Temperature (47200C) has beyond alert (0C), close to critical (0C) waiting...
While at it, preset CPU type values once to avoid multiple calls
of device_is_compatible() for same property.
Fixes: 3ee6ea443e ("cpu: imx_cpu: Print the CPU temperature for iMX8QM A72")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CPU type and rate detection is broken, for A35 cpu we get A53:
...
sc_pm_get_clock_rate: resource:0 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QXP RevB A53 at 0 MHz at 47C
Fixes: 55bc96f3b6 ("cpu: imx8: fix get core name and rate")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add REVC informaiton.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8QM registers two thermal devices for CPUs, get the temperature
from "cpu-thermal1" device for A72
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When current cpu is A53, using is_cortex_a53 could not detect A72
information, so check cpu device compatible property to get
the correct information.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Return 4 is not correct on i.MX8DX/DXL/8QM and etc. we need to count
available cpu node with device_type "cpu".
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When running on SoC with multiple clusters, the boot CPU may
not be fixed, saying booting from cluster A or cluster B.
Add a API that can return the udevice for current boot CPU.
Cpu driver needs to implement is_current_cpu interface for this
feature, otherwise the API only returns the first udevice in
cpu uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Different CPUs may support different address widths, meaning the amount of
memory they can address. Add a property for this to the cpu_info struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should not count in hart that is marked as not available in the
device tree in riscv_cpu_get_count().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Currently, timer driver is bound only for hart0.
There is no mandatory requirement that hart0 should always
come up. In fact, HiFive Unleashed SoC hart0 doesn't boot
in S-mode because it only has M-mode.
The timer driver should be bound for boot hart.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds a driver for RISC-V CPU. Note the driver will bind
a RISC-V timer driver if "timebase-frequency" property is
present in the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
The description string should not contain unnecessary characters,
like the ending '\n' or the leading 'CPU:'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds the initial support of the Broadcom BCM6838 SoC familly,
only cpu, dram, uart and leds are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In the device tree, the address for cpu is located in
the node "cpus", not in the cpu node (for exemple cpu@0).
So when probing cpu, the cpu address must be read in the
cpu parent.
The commit "cpu: bmips: convert to use live dt"
(sha1: c444afbbef)
change this behaviour and read the address in the
cpu node when probing cpu.
We fix this by reading the address in the cpu parent.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
