All i.MX8M needs TZASC ID SWAP set and locked, no need the check to
waste cpu cycles.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
When trying to boot via USB on i.MX8MN it is necessary to specify
the U-Boot environment location, otherwise the boot process simply
hangs.
Specify the environment location when booting from USB.
Tested on a imx8mn-evk.
Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes: e27bddff4b ("imx8m: Restrict usable memory to space below 4G boundary")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This is the only place where i.MX8M code does SMCCC call, remove it.
The output has little value as it prints some part of commit ID, and
worse, if there is no SMC handler installed, the code outright hangs
or crashes the system.
By removing this one instance of SMCCC call, U-Boot no longer depends
on SMC handlers and can boot without hanging in any case. If there is
a need to dump this commit ID, use CMD_SMC instead and do 'smc' call
from U-Boot shell or scripts instead of hard-coding SMCCC dependency
into architecture code. This particular code can be replaced by:
=> smc 0xc2000003 0 0 0 0 0 0
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable instruction cache early on to speed up the boot process on i.MX8M.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.
If provide both, kernel would failed to request the same gpio twice
and cause fec not work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The extcon is an decrepted property and not used by upstream Linux and
NXP 5.10 kernel, so we remove it before kicking linux in case it is in
dts. Otherwise distro kernel will not able to have usb function.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beside the fused modules on iMX8MP Lite, this part has also fused
GPU3D/2D, LVDS and MIPI DSI.
So we have to disable them for kernel and also disable MIPI DSI
in u-boot DTS for splash screen at runtime.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add settings for operating PLL at 933 MHz. This setting is useful in
case the LPDDR4 DRAM should operate at 1866 MHz or 3733 MT/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
To avoid passing around an extra register everywhere, save esr in
pt_regs like the rest. For proper alignment we need to have a second
(unused) register. All the printfs have to be adjusted, since
it's now an unsigned long and not an int.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is used in nxp u-boot tree.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add PLL 1.4 GHz, 1.5 GHz, 1.6 GHz, 1.8 GHz options for iMX8M SoCs
in case they should be operated faster, e.g. to improve boot time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Linux uses slightly different divider settings for the 1.2 GHz PLL
configuration, adjust the coefficients to match Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
According to TRM for i.MX8M Nano and Plus, GPR10 register contains lock
bit for TZASC_ID_SWAP_BYPASS bit. This bit is required to be set in
order to avoid AXI bus errors when GPU is enabled on the platform.
TZASC_ID_SWAP_BYPASS bit is alread set for all imx8m applicable
derivatives, but is missing a lock settings to be applied.
Set the TZASC_ID_SWAP_BYPASS_LOCK bit for those derivatives which have
it implemented.
Since we're here, provide also names to bits from TRM instead of using
BIT() macro in the code.
Fixes: deca6cfbf5 ("imx8mn: set BYPASS ID SWAP to avoid AXI bus errors")
Fixes: a07c718129 ("imx8mp: set BYPASS ID SWAP to avoid AXI bus errors")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Change boot device logic to also allow environment stored in fat and in
ext4 when booting from SD or from eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at env_get_location
to use IS_ENABLED instead for all modes, returning NOWHERE when no valid
mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Return the root clock values for MXC_CSPI_CLK, MXC_I2C_CLK,
MXC_UART_CLK and MXC_QSPI_CLK.
At least for the I2C clock the missing support leads to a wrong
configured I2C frequency. The expected value is 100kHz but the resulting
value is about 1MHz.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After all these board switch to binman, we could use common imximage.cfg
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
