Commit f11513d997 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Use the MEMA - MEMD registers on the PFUZE100 as bootcount
registers.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add missing MEMA - MEMD register definitions for PFUZE100.
Based on work from Heiko Schocher <hs@denx.de>.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add the PWM node and enable it for AST2600 EVB
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patchs add the signal description array for PWM pinctrl settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patch add the support of PWM controller which can be found at aspeed
ast2600 soc. The pwm supoorts up to 16 channels and it's part function
of multi-function device "pwm-tach controller".
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Macros PCI_CLASS_CODE_* and PCI_CLASS_SUB_CODE_* are unused and are
duplication of PCI_CLASS_* macros defined in pci_ids.h header file.
So remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace old macros PCI_CLASS_CODE_COMM and PCI_CLASS_SUB_CODE_COMM_SERIAL
by new macros defined in pci_ids.h. Old macros would be deleted in followup
commit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds support for using -Og when building U-Boot. According to the
gcc man page:
> -Og should be the optimization level of choice for the standard
> edit-compile-debug cycle, offering a reasonable level of optimization
> while maintaining fast compilation and a good debugging experience.
This optimization level is roughly -O1 minus a few additional
optimizations. It provides a noticably better debugging experience, with
many fewer variables <optimized out>.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a separate CONFIG_CC_OPTIMIZE_FOR_SPEED option in a choice,
in preparation for adding another optimization option. Also convert SH's
makefile to use this new option.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For consistency in runs, we need to always use the same pylint version.
Pin to 2.12.2 as this is what we have been using so far.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a legacy driver and the value is set in board config headers
without a CONFIG prefix. Remove the code.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.
Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.
With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.
Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
i2c changes for fixes-for-2022.04
- atsha204a-i2c.c
DTS and I2C fixes for Atmel ATSHA204 from Adrian
- i2c: fix always-true condition in i2c_probe_chip()
from Nikita
- eeprom: Do not rewrite EEPROM I2C bus with DM I2C enabled
from Marek
- clarify bootcount documentation fix from Michael
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.
For now, fix this by adding `vbus-supply` to usb3 node.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
With DM I2C, the EEPROM bus has been correctly configured in
eeprom_execute_command() already. Do not reconfigure it here
with hard-coded bus number again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch replaces use fdtdec_get_addr with simpler dev_read_addr().
fdtdec_get_addr doesn't work properly on ZynqMP-based (64bit) system. Although
not confirmed, it could be related to the fact, that quoting the documentation,
"This variant hard-codes the number of cells used to represent the address and
size based on sizeof(fdt_addr_t) and sizeof(fdt_size_t)".
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Once request is sent, and before receiving a response, the delay is required.
This patch fixes missing delay for before first response try.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
If the maximum number of wake-up attempts is exceeded, return -ETIMEDOUT.
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Documentation:
* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation
UEFI:
* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small
-----BEGIN PGP SIGNATURE-----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=Kn/h
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc5
Documentation:
* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation
UEFI:
* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small
The tools dtbdump.efi and initrddump.efi are useful for Python testing even
if CONFIG_EFI_SELFTEST=n.
Don't clear the screen as it is incompatible with Python testing.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The block IO protocol may be installed on any handle. We should make
no assumption about the structure the handle points to.
efi_disk_is_system_part() makes an illegal widening cast from a handle
to a struct efi_disk_obj. Remove the function.
Fixes: Fixes: 41fd506842 ("efi_loader: disk: add efi_disk_is_system_part()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The GUID of partitions is sufficient for identification and will stay
constant in the lifetime of a boot option. The preceding path of the
device-path may change due to changes in the enumeration of devices.
Therefore it is preferable to use the short-form of device-paths in load
options. Adjust the 'efidebug boot add' command accordingly.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The boot manager must support loading from boot options using a short-form
device-path, e.g. one where the first element is a hard drive media path.
See '3.1.2 Load Options Processing' in UEFI specification version 2.9.
Fixes: 0e074d1239 ("efi_loader: carve out efi_load_image_from_file()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Let function efi_dp_find_obj() additionally check if a given protocol is
installed on the handle relating to the device-path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
