Add a new 'cedit' command which allows editing configuration using an
expo. The configuration items appear as menus on the display.
This is extremely basic, only supporting menus and not providing any way
to load or save the configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
On the XEA (imx287) system the FAT file system is not used neither in
SPL nor u-boot proper.
Hence, to save ~6KiB of u-boot.img size - it has been disabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA system (imx287 based) is not using support for EXTLINUX and VBE.
As those configuration options have been enabled by default with modern
Kconfig it is safe to explicitly disable them.
After that change the u-boot.img size has been reduced by ~16 KiB.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable CONFIG_SPL_GPIO_HOG option to be able to control GPIO hogs from
SPL.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable CONFIG_SPL_GPIO_HOG option to be able to control GPIO hogs from
SPL.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add basic config for Sipeed Lichee PI 4A board which make it capable of
booting into serial console.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Enabled ID_EEPROM and I2C configuration for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-By: Leo Yu-Chi Linag <ycliang@andestech.com>
Enable DWC_ETH_QOS and PHY_MOTORCOMM configuration to support ethernet
function for StarFive VisionFive 2 board,including versions 1.2A and
1.3B.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between 1.2A and 1.3B is dynamically configured according
to the PCB version, and there is no difference on the board device tree,
so the same DT file can be used.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mn_beacon.env and reference it from the defconfigs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mm_beacon.env and reference it from the defconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Select DM_ETH_PHY so that the reset-gpios property of the ethphy node
can be used.
Also select DM_PCA953X, which is needed for resetting the
ethernet PHY on the carrier board via the PCA9534 I/O expander.
Commit 4e5114daf9 ("imx8mn: synchronise device tree with linux") did
synchronise device tree with linux, which in effect removed obsolete
PHY reset properties and replaced them with new mdio DM
properties. But the commit didn't activate DM_ETH_PHY or DM_PCA953X.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
The single binary version of u-boot for XEA board is used to debrick and
factory programming.
The produced u-boot.sb is a single file, which allows having fully
operational u-boot prompt loaded with imx287 ROM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA board now supports the DM_SERIAL feature in u-boot.
The SPL is using the SPL_OF_PLATDATA - i.e. NOT SPL_DM_SERIAL to
reduce the overall size of the SPL binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After the re-sync with Linux kernel (v6.0) of the XEA DTS
(SHA1: 7d08ddd09b) the alias
for SPI bus, to which SPI-NOR memory is connected, has changed from
'spi3' to 'spi2'.
To be in sync with current u-boot's xea dts, the default bus number
(which allows running 'sf probe' without any extra parameters given)
has been adjusted.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch adjusts XEA's PMU setup as this board is supposed to be
mainly powered from DCDC_BATT source.
Moreover, in this HW design the VDD_4P2 is not used as well.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To allow U-Boot to fit within emmc boot partitions move the env from
just under 16MiB to just under 4MiB as some emmc devices used on venice
boards have 4MiB boot partitions. This still leaves plenty of room for
U-Boot.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add GPIO name lookup so that you can act on GPIO's by name vs controller
id:
Before:
u-boot=> gpio input pci_wdis#
GPIO: 'pci_wdis#' not found
Command 'gpio' failed: Error -22
After:
u-boot=> gpio input pci_wdis#
gpio: pin pci_wdis# (gpio 103) value is 1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This is required to boot a FIT image, otherwise the caam_jr driver is
not initialized and the hash verification fails with the following
error:
Verifying Hash Integrity ... sha256dev_get_priv: null device
CAAM was not setup properly or it is faulty
Signed-off-by: Sergio Prado <sergio.prado@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The imx8mm_beacon SOM has a QSPI part attached to the FSPI controller.
Update the header and spl files to support booting from NOR flash and
add imx8mm_beacon_fspi_defconfig to support this configuration.
Signed-off-by: Adam Ford <aford173@gmail.com>
DM_GPIO depends on GPIO to be enabled but select will cause that DM_GPIO is
selected without GPIO which ends up in compilation error:
undefined reference to `dm_gpio_set_value'
undefined reference to `dm_gpio_get_value'
undefined reference to `dm_gpio_free'
undefined reference to `gpio_request_by_name'
Signed-off-by: Michal Simek <michal.simek@amd.com>
[trini: Fix configs which had relied on these select's]
Signed-off-by: Tom Rini <trini@konsulko.com>
The original names picked for the DT doesn't match Linux's naming scheme
and it was renamed there a while ago. Rename it in U-Boot to allow
easily syncing dts between the two projects.
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
As the serial devices are configured in the device tree, enable
DM_SERIAL in the ls1046afrwy defconfigs.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As the serial devices are configured in the device tree, enable
DM_SERIAL in the ls1046ardb defconfigs.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As the serial devices are configured in the device tree, enable
DM_SERIAL in the ls1043ardb defconfigs.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Use of CONFIG_SPL_FIT_SIGNATURE=y cause CONFIG_LEGACY_IMAGE_FORMAT=n as
default, this prevent boot scripts in legacy image format from working
and was an unintended change in the listed fixes commits:
Wrong image format for "source" command
Add CONFIG_LEGACY_IMAGE_FORMAT=y to defconfig for affected boards to
restore support for boot scripts in legacy image format.
Fixes: 3bf8e40807 ("board: rockchip: add Radxa ROCK5B Rk3588 board")
Fixes: cf777572ca ("rockchip: rockpro64: Use SDMA to boost eMMC performance")
Fixes: 6e2b8344d6 ("rockchip: rock-pi-4: Use SDMA to boost eMMC performance")
Fixes: 1bf49d5a4a ("rockchip: rk3566-radxa-cm3-io: Update defconfig")
Fixes: 703c170b40 ("rockchip: rk3568-evb: Update defconfig")
Fixes: 68000f750a ("rockchip: rk3568-rock-3a: Update defconfig")
Fixes: 6fb02589a6 ("rockchip: rk3588-evb: Update defconfig")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Currently, the imx93_evk is configured with CONFIG_ENV_IS_IN_MMC and the
chosen environment offset in the config is 0x400000. Unless the user
programs the associated fuses, this offset is the default secondary boot
image offset used by the i.MX 93 ROM bootloader. With certain
combinations of environmental variables, the CRC and beginning of the
environment can potentially falsely appear as a valid boot image
container header. If the expected "sw_version" offset within this
mistaken boot image container is greater than the primary's, the ROM
bootloader can skip booting of the primary image altogether and attempt
to boot with the content of the environment data. This will then hang
the system.
To fix this, move the environment from 0x400000 to 0x700000 reserving up
to 3 MB at 0x400000 for any actual secondary user image container.
Signed-off-by: Ken Sloat <ken.s@variscite.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add configurations for the Videostrong KII Pro set-top box.
This defconfig is cloned from the WeTek Play2's.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
Link: https://lore.kernel.org/r/20230507124109.31778-3-vitali64pmemail@protonmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The AD401 board is the Amlogic A1 SoC reference board
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230505125639.3605-6-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Two conflicting bootcmds were included in the environment.
Streamline to defining the bootcmd only in the env file.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
