This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The default value of CONFIG_SYS_MALLOC_F_LEN (0x400)
leaves U-Boot with not enough memory to load i2c driver
before relocate, causing it to hang.
Change the default value of CONFIG_SYS_MALLOC_F_LEN
for below SoCs,
- LS1012A
- LS1021A
- LS1043A
- LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds DM_FLAG_PRE_RELOC flag to probe i2c driver
before relocation
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix below SPL build error when DM_I2C is enabled,
- arch/arm/cpu/armv8/built-in.o: In function `board_init_f:
arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all'
arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30):
relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
`i2c_init_all'
make[2]: *** [spl/u-boot-spl] Error 1
make[1]: *** [spl/u-boot-spl] Error 2
make: *** [sub-make] Error 2
arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f':
arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit
declaration of function 'i2c_init_all'; did you mean 'misc_init_r'?
[-Wimplicit-function-declaration]`
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable FSPI controller support. So, flash environment can now be used
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support of "qixis_reset emmc" command for lx2160a based platforms
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sync the interrupt properties with the ones from Linux. Also use the
constants provided by the dt-bindings header. Please note, that there
are actual changes/fixes in the irq flags. U-Boot won't use the
interrupt properties anyway. It's just to be consistent with the Linux
device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Also align the fspi node with the kernel one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a new option to enable the DROP_FFS flag when flashing UBI images to
NAND in order to drop trailing all-0xff pages.
This is similar to the existing FASTBOOT_FLASH_NAND_TRIMFFS option.
Signed-off-by: Guillermo Rodriguez <guille.rodriguez@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Invalidate dcache line before accessing Setup Packet contents. Otherwise
driver will see stale content on non coherent architecture.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
-----BEGIN PGP SIGNATURE-----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=PvYc
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (2nd)
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
If the "source" command is not given the address, it uses
CONFIG_SYS_LOAD_ADDR, which is compile-time determined.
Using the "loadaddr" environment variable is handier because it is
relocated according to the memory base when CONFIG_POSITION_INDEPENDENT
is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
gd->ram_base is not set at all if the end address of the DRAM ch0
exceeds the 4GB limit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the reset controlling of the Denali NAND driver (denali_dt.c)
works for this platform, remove the adhoc reset deassert code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the denali NAND driver in U-Boot configures the
SPARE_AREA_SKIP_BYTES based on the CONFIG option.
Recently, Linux kernel merged a patch that associates the proper
value for this register with the DT compatible string.
Do likewise in U-Boot too.
The denali_spl.c still uses CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.
Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Fixes: ed784ac382 ("mtd: rawnand: denali: add reset handling")
Signed-off-by: Marek Vasut <marex@denx.de>
[yamada.masahiro: reword the commit description]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit e1910d93b8 ("doc: driver-model: Convert MIGRATION.txt to
reST") MIGRATION.txt has been converted to migration.rst, so update
the Makefile references accordingly.
Fixes: e1910d93b8 ("doc: driver-model: Convert MIGRATION.txt to reST")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In upstream libfdt, 6dcb8ba4 "libfdt: Add helpers for accessing
unaligned words" introduced changes to support unaligned reads for ARM
platforms and 11738cf01f15 "libfdt: Don't use memcpy to handle unaligned
reads on ARM" improved the performance of these helpers.
In practice however, this only occurs when the user has forced the
device tree to be placed in memory in a non-aligned way, which in turn
violates both our rules and the Linux Kernel rules for how things must
reside in memory to function.
This "in practice" part is important as handling these other cases adds
visible (1 second or more) delay to boot in what would be considered the
fast path of the code.
Cc: Patrice CHOTARD <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Link: https://www.spinics.net/lists/devicetree-compiler/msg02972.html
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Coreutils command nproc can be used on Linux and BSD to count the number of
available CPU cores. Use this instead of relying on the parsing of the
Linux specific proc file system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As hinted by GCC 9, there is a return statement that returns
an uninitialized variable in optee_copy_firmware_node().
This patch addresses this.
Signed-off-by: Christoph Müllner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
This removes the arch-specific checks for "checkcpu" function from the init
sequence. Make "checkcpu" generic and provide a weak nop stub instead.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
New analysis by the tool has shown that we have some cases where we
weren't handling the error exit condition correctly. When we ran into
the ENOMEM case we wouldn't exit the function and thus incorrect things
could happen. Rework the unwinding such that we don't need a helper
function now and free what we may have allocated.
Fixes: 18030d04d2 ("GPT: fix memory leaks identified by Coverity")
Reported-by: Coverity (CID: 275475, 275476)
Cc: Alison Chaiken <alison@she-devel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Jordy <jordy@simplyhacker.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This enables readning the cpuid from e-fuse, and deriving a static
MAC address from it.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add alias for mmc/sdmmc so that we can have a fix mmc number for emmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rockchip use CONFIG_SPL_OPTEE for OPTEE support, which is load and run
before U-Boot, but not use CONFIG_OPTEE which is after U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add rk3328-sdram-ddr4-666.dtsi for support ddr4 init.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
No need to do twice data training for rk3328 ddr sdram, we re-use the
setting for both channel. And adjust the sdram_init properly for correct
init flow.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Rockchip has documentation file, doc/README.rockchip but
which is not so readable to add or understand the existing
contents. Even the format that support is legacy readme
in U-Boot.
Add rockchip specific documentation file using new rst
format, which describes the information about Rockchip
supported boards and it's usage steps.
Added minimal information about rk3288, rk3328, rk3368
and rk3399 boards and usage. This would indeed updated
further based on the requirements and updates.
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot specific dtsi file for rk3188 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3188.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot specific dtsi file for rk3036 SoC. This
would help to add U-Boot specific dts nodes, properties
which are common across rk3036.
Right now, the file is empty, will add required changes
in future patches.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
