This commit combines catching missing memory and calibration data into
one if() block. It further prints pertinent information in determining
why the failure occurred.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add memory configuration for an IMX6SDL + 1GB density DRAM.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The initial revision of the GW551x does not connect enough signals between
the HDMI receiver and the IMX6 CSI for 16bit capture mode necessary for
yuv422smp capture. Future revisions will, but for the initial rev force it
to yuv422bt656 mode which requires an 8bit video data bus.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The HDMI receiver used on the GW54xx and GW551x has a 16bit video data bus
interconnect between it and the IMX6 CSI. This can be used in two different
modes, each having advantages and disadvantages. Allow the hdmiinfmt env
var to specify which format is desired (yuv422smp or yuv422bt656).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW522x is functionally the same as a GW52xx except for PCIE_RST#
GPIO. Add a DT fixup to change this gpio upon bootup.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds information about the Gateworks System Controller to the gsc command
such as the firmware version, firmware CRC and status of the GSC watchdog
(if its enabled and if its tripped).
Additionally the 'gsc wd' command can be used to enable or disable the
watchdog with the following usage:
gsc wd enable [30|60]
gsc wd disable
Note that the GSC registers are battery-backed by the GSC coincell so once
eanbled, they remain enabled across power-cycles or until either the GSC
firmware has been updated or FLASH has been re-programmed by the Gateworks
JTAG adapter.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Configure kernel device-tree for display from env var. This is useful
to specify the display present when the device-tree supports multiple
non-detectable display configurations.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Certain older kernels in use by some customers erroneously define a uart3
for GW54xx with a pinmux that conflicts with NAND. This will remove
that node to avoid such conflicts.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Updated 16bit DDR calibration using values obtained from running the
i.MX6 DDR Stress Test tool over a set of boards over full operationg
temperature.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW551x-A revision does not have the CSI0_DATA_EN pin connected, therefore
we need to make sure that signal is not muxed to the CSI_DATA_EN signal
internally and do so by steering it to the unused GPIO5_IO20.
We do this so that the kernel device-tree can properly define the signal for
RevB and beyond boards that do have this hooked up properly and require it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a new voltage rail added in various -C revision PCB's.
Additionally make VDD_CORE, VDD_SOC, and VDD_IO2 common as all Ventana boards
have those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Certain OS bootscripts need to know how much memory a board has to adjust
kernel parameters (namely Android). This allows those boards to determine
mem size in MB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The min/max of each depends not only on board but on CPU. Simplify by removing
this rarely needed and difficult to maintain feature and just display the
rails and their values.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Added support in default boot scripts to find kernel/dtbs on a boot volume
separate from rootfs volume.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW551x is a small form factor board based on the IMX6 SoC that includes:
* up to 512MB DDR3 memory
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
A board level errata causes the IMX6 watchdog to be unstable on the GW51xx
RevA and RevB boards which can cause the watchdog to trip extremely early
(under 5seconds) under certain operating conditions. Disable the watchdog
node in the device-tree to work around this issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the 'i2c edid' command to query and display data from an attached
HDMI monitor of LVDS display with an EDID device.
Example:
Ventana > i2c dev 2 && i2c edid 0x50
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for the USB mass storage gadget to enable access to on-board
storage.
Example:
Ventana > ums 0 mmc 0 # provide ums access to the uSD
Ventana > ums 0 usb 0 # provide ums access to the first USB device
Ventana > ums 0 sata 0 # provide ums access to an mSATA device
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 Datasheets specifies that when the IMX6 LDO is enabled
(internal Anatop LDO's for VDD_ARM, VDD_SOC, and VDD_xPU) you need to
provide 1350mV on VDD_ARM_IN and VDD_SOC_IN for IMX6Q@1GHz (Automotive)
and 1275mV for IMX6DL@800MHz (Industrial). While we are still about 50mV
shy on the IMX6Q operating at 1GHz we set it to the max we can and leave it
up to the kernel to implement a regulator driver for the LTC3676 and put
the LDO's in bypass mode which allows us to drop the voltages by 125mV
respectively.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW52xx has a MUX that can direct front-panel USB OTG to one of the
miniPCIe sockets (for use with a cellular modem for example). Use hwconfig
to steer this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks Ventana boards don't all use IMX6 FEC, so lets define default
ethprime based off the first detected device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
I've encountered issues when using 4k packets through certain switches. For
now disable this and go back to using MTU size packets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add 'fdt_fixup_display' function to fixup device-tree native-mode property
of display-timings node to select timings for a specific display.
This is useful if a device-tree has configurations for multiple
display timings for undetectable displays.
see kernel Documentation/devicetree/bindings/video/display-timing.txt
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Simon Glass <sjg@chromium.org>
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reading the boot mode pins after power-up does not necessarily represent the
boot mode used by the ROM loader. For example the state of a pin may have
changed because a recovery switch which was pressed to enter USB mode is
already released after plugging in USB.
The ROM loader stores the value a fixed address in OCRAM. Use this value
instead of reading the boot map pins.
The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the
MX28EVK:
http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch
Leave the boot mode detection for the i.MX23 untouched. Someone has to test
whether the i.MX ROM loader does also store the boot mode in OCRAM and if the
address match.
This patch superseeds my incorrect patch:
ARM: mxs: get boot mode from OTP
http://patchwork.ozlabs.org/patch/454930/
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Stefano Babic <sbabic@denx.de>
Since commit 79d75d7527 (ARM: move -march=* and -mtune= options to
arch/arm/Makefile), all the Tegra boards are broken because the SPL
is built for ARMv7.
Insert Tegra-specific code to arch/arm/Makefile to set compiler
flags for an earlier ARM architecture.
Note:
The v1 patch for commit 79d75d7527 *was* correct when it was
submitted. Notice it was originally written for multi .config
configuration where Kconfig set CONFIG_CPU_V7/CONFIG_CPU_ARM720T for
Tegra U-Boot Main/SPL, respectively. But, until it was merged into
the mainline, commit e02ee2548a (kconfig: switch to single .config
configuration) had been already applied there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced
a different method to return from save_boot_params(). The SPL support
for AXP has been pulled and changing to this new method is now
required for SPL to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
While testing "arc: make sure _start is in the beginning of .text
section" I haven't done proper clean-up of built binaries and so missed
another tiny bit that lead to the following error:
--->8---
LD u-boot
arc-linux-ld.bfd: cannot find arch/arc/lib/start.o
Makefile:1107: recipe for target 'u-boot' failed
make: *** [u-boot] Error 1
--->8---
Fix is trivial: put "start.o" in "extra-y".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This consolidates the flash settings for the Integrator
and activates the new ARM flash image support for them
so images can be loaded by name from flash.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This modifies the vexpress64 Juno configuration so that
it will by default load and boot a kernel and a device tree
from the images stored in the NOR flash. When we are
at it, also define the proper command line for the Juno and
indicate that the USB stick (/dev/sda1) is the default
root file system.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ARM reference designs all use a special flash image format
that stores a footer (two versions exist) at the end of the last
erase block of the image in flash memory.
Version one of the footer is indicated by the magic number
0xA0FFFF9F at 12 bytes before the end of the flash block and
version two is indicated by the magic number 0x464F4F54 0x464C5348
(ASCII for "FLSHFOOT") in the very last 8 bytes of the erase block.
This command driver implements support for both versions of the
AFS images (the name comes from the Linux driver in drivers/mtd/afs.c)
and makes it possible to list images and load an image by name into
the memory with these commands:
afs - lists flash contents
afs load <image> - loads image to address indicated in the image
afs load <image> <addres> - loads image to a specified address
This image scheme is used on the ARM Integrator family, ARM
Versatile family, ARM RealView family (not yet supported in U-Boot)
and ARM Versatile Express family up to and including the new
Juno board for 64 bit development.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
