There is no support to initialize DRAM on rk3308 SoC using U-Boot
TPL or SPL, and therefore an external TPL binary must be used to
package a bootable u-boot-rockchip.bin image.
Default ROCKCHIP_EXTERNAL_TPL to yes if ROCKCHIP_RK3308.
Remove useless TPL_SERIAL.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Port the Rockchip IO-domain driver for RK3568 from linux.
The driver auto probe after bind to configure IO-domain based on the
regulator voltage. Compared to the linux driver this driver is not
notified about regulator voltage changes and only configure IO-domain
based on the initial voltage autoset by the regulator.
It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage
and IO-domain may end up out of sync.
Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add
rk3568 support").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The voltage value for switchout converters is always reported as 0 uV.
When the switch is enabled, it's voltage is same as input supply.
Fix this by implementing get_value for switchout converters.
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Information from the first range group is always used to calculate the
voltage returned for buck converters. This may result in wrong voltage
reported back to the regulator_get_value caller.
Traverse all the possible BUCK ranges to fix this issue.
Fixes: addd062bea ("power: pmic: rk816: support rk816 pmic")
Fixes: b62280745e ("power: pmic: rk805: support rk805 pmic")
Fixes: b4a35574b3 ("power: pmic: rk817: support rk817 pmic")
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, simplify buck get_value, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable missing PCIe Kconfig options now that PCIe bifurcation is fixed
to make use of the two on-board RTL8125B and the M.2 slot on NanoPi R5C
and NanoPi R5S.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update and sync Kconfig options for NanoPi R5C and NanoPi R5S with other
RK3568 boards.
SPL_FIT_SIGNATURE is enabled to add a checksum validation of the FIT
payload, also add LEGACY_IMAGE_FORMAT to keep boot scripts working.
OF_SPL_REMOVE_PROPS, SPL_DM_SEQ_ALIAS and SPL_PINCTRL change ensure
pinctrl for eMMC, SD-card and UART2 is applied in SPL.
MMC_HS200_SUPPORT and SPL counterpart is enabled to speed up eMMC load
times from on-board eMMC 5.1 modules.
Drop remaining unused or unsupported options to sync with other RK3568
boards.
Also sync device tree from linux v6.4 and drop u-boot,spl-boot-order and
use the default from rk356x-u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Route signal from comb PHY instead of PCIe3 PHY to PCIe1l0 and PCIe1l1.
Fixes use of pcie2x1l0 on ROCK 5B.
Code imported from mainline linux driver.
Fixes: c5b4a012bc ("phy: rockchip: naneng-combphy: Support rk3588")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3588 variant to the driver.
Code imported almost 1:1 from mainline linux driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure aggregation or bifurcation mode on RK3568 based on the value
of data-lanes property.
Code imported almost 1:1 from mainline linux driver.
Fixes: 6ec62b6ca6 ("phy: rockchip: Add Rockchip Synopsys PCIe 3.0 PHY")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a phy_init ops in preparation for upcoming support of a RK3588
variant in the driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use clk_bulk API and syscon_regmap_lookup_by_phandle to
simplify in preparation for upcoming support of a RK3588 variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set number of lanes and link width speed control register based on the
num-lanes property.
Code imported almost 1:1 from dw_pcie_setup in mainline linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
Sync k3-j721e DTS with kernel.org v6.6-rc1.
* Use mcu_timer0 defined in k3-j721e-mcu-wakeup.dtsi and remove
timer0, we have its clocks set up in clk-data now
* Remove hbmc node as support is buggy and needs to be fixed
* Remove aliases and chosen node, use them from Kernel
* Remove /delete-property/ and clock-frequency from sdhci,
usbss, and mcu_uart nodes as we have them in clk and dev data
* Remove dummy_clocks as they are not needed
* Remove cpsw node as it is not required since it has been fixed
in U-Boot
* Remove pcie nodes, they are not needed
* Remove mcu_i2c0 as it is used for tps659413 PMIC in j721e-sk
for which support is not yet added
* Change secproxy nodes to their Linux definitions
* Remove overriding of ti,cluster-mode in MAIN R5 to default to
lockstep mode same as Kernel
* Retain tps6594 node as TPS6594 PMIC support is still under
review in the Kernel [1], cleanup will be taken post its merge
[1] https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Get rid of k3-j721e-r5-*-u-boot.dtsi as it is not
necessary. Change the inclusion hierarchy to be as follows:
k3-j721e-<board>.dts---
-
-->k3-j721e-r5-<board>.dts
-
k3-j721e-<board>-u-boot.dtsi---
Reason for explicitly mentioning the inclusion of -u-boot.dtsi in code
although it could've been automatically done by U-Boot is to resolve
some of the dependencies that R5 file requires.
Also remove duplicate phandles while making this shift as well as remove
firmware-loader as it serves no purpose without "phandlepart" property.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Kernel commit d93036b47f35 ("arm64: dts: ti: k3-j721e-mcu_wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting up boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which calls dm_timer_init()
which then gets the tick-timer: mcu_timer0. mcu_timer0 uses k3_clks
(clock controller) and k3_pds (power controller) from the dmsc node that
forces probe of the ti_sci driver of TIFS that hasn't been loaded yet!
Running ti_sci_cmd_get_revision from the probe leads to panic since no
TIFS and board config binaries have been loaded yet. Resolve this by
moving ti_sci_cmd_get_revision to ti_sci_get_handle_from_sysfw as a
common point of invocation for both legacy and combined boot flows.
Before doing this, it is important to go through whether any sync points
exist where revision is needed before ti_sci_get_handle_from_sysfw is
invoked. Going through the code along with boot tests on both flows
ensures that there are none.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which eventually calls
dm_timer_init() to grab the tick-timer, which is mcu_timer0. Since we
need to set up the clocks before using the timer, move clk_k3 driver
probe before k3_sysfw_loader to ensure we have all necessary clocks set
up before.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
U-Boot uses mcu_timer0 as the tick-timer, so add it to device list.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken. This is because nodes
marked as 'bootph-pre-ram' are not available at u-boot proper before
relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Reported-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warnings:
<stdout>: Warning (reg_format): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (unit_address_vs_reg): /bus@f4000/ethernet@8000000/mdio@f00: node has a unit name, but no reg or ranges property
<stdout>: Warning (pci_device_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
<stdout>: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #size-cells value
<stdout>: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0100:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0000:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (phys_property): /bus@f4000/ethernet@8000000/ethernet-ports/port@2:phys: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move cbass_mcu node to -r5-sk.dts as it is only required
for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
USB and MMC nodes need pinmux.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warning:
<stdout>: Warning (dmas_property): /bus@f4000/ethernet@8000000:dmas: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move vtt_supply and cbass_mcu node to -r5-evm.dts as
it is only required for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
This does not move configs anymore, but queries them, based on a database
it can build. Rename the tool to better reflect its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since moveconfig now just does what it is told (build database or sync
defconfigs) we don't need to print what it is doing. Drop this info, which
is of very little use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than printing all the failed boards, which are now easily visible
on the terminal, just show a summary. Sort it by defconfig and drop the
'_defconfig' suffix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Show the number of accumulated failures when processing. Use a shorter
format with colour.
An unwanted space appears before the defconfig name on every item except
the last. Fix that while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the existing terminal code to handle ANSI colours. Enable colour by
default if the output is going to a terminal.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the process is finished, moveconfig leaves a line saying that all
boards were processed (for better or worse). Drop this, since it is
unncessary.
Future work will provide a summary at the end instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Output a single line in the case where the defconfig only has one line
of output. Show the name without the _defconfig suffix, since that is the
same for all boards.
Use a list for the log so it is easier to process at the end.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no point in listing a board if everything went well. It makes it
harder to see the failures, particularly on a fast machine.
Suppress output unless something actually happened.
Drop the 'Syncing by savedefconfig' since this is selected by the -s and
is the same for all boards in this mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
