For board using STPMIC1, the vddcore is provided by BUCK1 of STPMIC1
and need to be updated for 800MHz support and only after the clock
tree initialization.
The VDDCORE voltage value is provided by clock driver, saved in global
variable opp_voltage_mv and udpated in SPL board_early_init_f(),
just after clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move function board_ddr_power_init() in a new file stpmic1 in
board/st/common to avoid duplicated code in each board using
stpmic1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
On DK1/2 board, when a 1.5A power supply is detected, a warning
message is displayed. In this message, "1.5mA" is displayed instead
of "1.5A".
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch avoids infinite loop when I/O compensation failed,
it adds a 1s timeout to detect error.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
It is not allowed to change the user setting of bootdelay, so
remove the check of the boot-source to disable it dynamically
in board_late_init()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For booting Linux in the generic distro mechanism and support of
FDTDIR in extlinux.conf , cmd/pxe.c retrieves the FDT file name
from "fdtfile" environment variable.
Dynamically build this variable with compatible of STMicroelectronics
boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Software workaround for I2C issue on EV1 board,
configure the IRQ line for touchscreen before LCD reset
to fix the used I2C address.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Force boot-led ON and no more rely on default-state.
This patch avoid device-tree modification for U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit commit dd2810851e ("stm32mp1: board: support of
error led on ed1/ev1 board") the attended behavior was no more
respected in case of low power source detection on DK2.
The expected behavior is either the error LED keeps blinking for ever,
or blinks 2 or 3 times and must stay ON.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from
NOR or NAND/SPI-NAND is detected.
This patch avoids to define the save MTD partition name for NOR and NAND
devices and issue with latest kernel: only the needed MTD partitions
are defined.
For boot from NOR
1/ bootloader (TF-A, U-Boot and OP-TE) in NOR
2/ one large UBI partition in NAND
For boot from NAND
1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition
2/ one large UBI partition
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use the correct macro to test presence CONFIG_LED:
replace CONFIG_IS_ENABLED(CONFIG_LED) by CONFIG_IS_ENABLED(LED)
Issue see during review unrelated patch
"board: stm32mp1: update management of boot-led"
http://patchwork.ozlabs.org/patch/1264823/
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Display the reference MBxxxx found in OTP49
only for STMicroelectronics boards when CONFIG_CMD_STBOARD
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
# Conflicts:
# board/st/stm32mp1/stm32mp1.c
Update the command stboard to support the updated coding of OTP 59 with
finished good.
The ST product codification have several element
- "Commercial Product Name" (CPN): type of product board (DKX, EVX)
associated to the board ID "MBxxxx"
- "Finished Good" or "Finish Good" (FG):
effective content of the product without chip STM32MP1 (LCD, Wifi, …)
- BOM: cost variant for same FG
(for example, several provider of the same component)
For example
- commercial product = STM32MP157C-EV1
- Finished Good = EVA32MP157A1$AU1
Booth information are written on board and these information is also saved
in OTP59:
bit [31:16] (hex) => Board id, MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
The updated command is:
stboard [-y] <Board> <VarCPN> <Revision> <VarFG> <BOM>
And the displayed STMicroelectronics board identification is:
Board: MB<Board> Var<VarCPN>.<VarFG> Rev.<Revision>-<BOM>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Lock the OTP used for board identification for the ST boards after
programming.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Read the value directly from the OTP and no more of the shadows
to avoid the need of reboot after stboard command to have correct value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update management of misc_write, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change the dfu functions dfu_otp_read and dfu_pmic_read to static,
this patch avoids warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add include for dfu, add prototype for set_dfu_alt_info
and avoid warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update readme:
- list the supported SOC and change family to STM32MP15x
- add warning on OTP write and prerequisite:
check if MAC address is not yet provisioned.
- Use filesize for mmc write command (avoid to write all partition
with ${partsize}). ${filesize} and ${partsize} are set by previous
load command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig
for ST board with NOR support (STM32MP15xx-EV1 boards)
- CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB)
- CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH)
This Patch prepares the U-Boot support of boards with STM32MP15x SOC
not provided by STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the ST command in board/st/common, as this command is only used
by ST board. Prepare the support in U-Boot of boards with STM32MP15x
SOC but not STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since the coprocessor state is tracked in a backup register, there is
no more need for tracking it in an environment variable : remove it.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is only used by a few files so it should not be in the common header.
Move it out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add read for OTP and PMIC NVM with alternates
on virtual DFU device.
Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds the support of the spi nand device in mtdparts command
and in dfu_alt_info.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Generate automatically dfu_alt_info for the supported device.
The simple command "dfu 0" allows to start the dfu stack on usb 0
for the supported devices:
- dfu mtd for nand0
- dfu mtd for nor0
- dfu mmc for SDCard
- dfu mmc for eMMC
- dfu ram for images in DDR
The DUF alternate use the "part", "partubi" and "mmcpart" options
to select the correct MTD or GPT partition or the eMMC hw boot partition.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Select the correct USB product id used by the download gadget
for ST stm32mp1 boards.
The board stm32mp1 select the correct product id, as defined in
http://www.linux-usb.org/usb.ids for the STMicroelectronics
vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM):
- dfu = 0xdf11 : STM Device in DFU mode
it is the value used by ROM code and reused for stm32prog
command
- fasboot = 0x0afb : Android Fastboot device
- others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM)
Mass Storage Device
it is used for UMS command / usb_dnl_ums
This patch avoid conflict when the same USB VID/PID is used for
ums, fastboot or dfu command (two different protocols associated
to the same PID).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Align the board and driver prototype for board_interface_eth_init
to avoid execution issue (the interface_type parameter is defined
as int or phy_interface_t).
To have a generic weak function (it should be reused by other driver)
I change the prototype to use directly udevice.
This prototype is added in netdev.h to allow compilation check
and avoid warning when compiling with W=1 on file
board/st/stm32mp1/stm32mp1.c
warning: no previous prototype for 'board_interface_eth_init'\
[-Wmissing-prototypes]
int board_interface_eth_init(int interface_type, ....
^~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add example of its files to generate FIT to start kernel
on ev1 or dk2 board with
- only kernel and dtb = fit_copro_kernel_dtb.its
- kernel, M4 copro firmware and dtb = it_copro_kernel_dtb.its
Add extlinux example to manage config in generated FIT.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Implements copro image loading with FIT.
Once image is loaded with remoteproc,
the M4 coprocessor is automatically started.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update management of misc_read, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update management of misc_read in sysconf_init, which now return
length of data after the commit 8729b1ae2c ("misc: Update read()
and write() methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update the stm32mp1 baord after the commit 8729b1ae2c
("misc: Update read() and write() methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Due to kernel DT alignment, pwr-supply is renamed to vdd-supply
and is a subnode of pwr-regulators.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As for Audio codec IC, HDMI IC is not "IO safe".
HDMI regulators (v3v3 and v1v2) must be enabled to allow
I2C1 bus usage. HDMI IC must be under reset during power up
and keep HDMI and AUDIO devices in reset while they are not
used in U-Boot to keep them in low power mode
(each device can be kept in reset independently keeping their
power supplies ON until kernel).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Depending on backup register value, we maintain the debug unit
powered-on for debugging purpose.
Only BUCK1 is required for powering the debug unit, so revert
the setting for all the other power lanes, except BUCK3 that
has to be always on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch solves the following warnings:
warning: no previous prototype for 'board_quiesce_devices' [-Wmissing-prototypes]
void board_quiesce_devices(void)
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
U-Boot activates regulators by reading the "regulator-boot-on"
property in DT; it is requested by M4 early Boot feature.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Called to configure Ethernet PHY interface selection and
configure clock selection in RCC Ethernet clock tree.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Add 2 new checks:
- detect when USB TYPE-C cable is not plugged correctly.
In this case, GND and VBUS pins are connected but not CC1
and CC2 pins.
- detect is an USB Type-C charger supplies more than 3 Amps
which is not compliant with the USB Type-C specification
In these 2 situations, stop the boot process and let red led
blinks forever.
V cc1 | V cc2 | power supply | red led | console message
range (Volts) |range (Volts)| (Amps) | blinks |
--------------|-------------|--------------|---------|-----------------------------------
> 2.15 | < 0.2 | > 3 | for ever| USB TYPE-C charger not compliant with specification
[2.15 - 1.23[ | < 0.2 | 3 | NO | NO
[1.23 - 0.66[ | < 0.2 | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | < 0.2 | 0.5 | 2 times | WARNING 500mA power supply detected
< 0.2 | < 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
> 0.2 | > 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update env_get_location() to be able to save environment into
NOR (SPI_FLASH).
Series-cc: pde, cke, pch, uboot-stm32
Cover-letter:
Add saveenv support for STM32MP1
This series adds saveenv support for STM32MP1 on several boot
devices. STM32MP1 is able to boot on eMMC, sdcard and NOR
(NAND support is not fully supported).
On eMMC and sdcard, environment is saved in EXT4 partition
On NOR, environment is saved in a dedicated partition
On NAND, environment is saved in a UBI volume.
This series:
- enables NAND and NOR support on ev1 board
- enables ENV_IS_IN_SPI_FLASH, ENV_IS_IN_UBI, ENV_IS_IN_EXT4
flags
- fixes get_mtdparts()
- allows to override interface, device and partition for ext4
environment
- updates rule to set ENV_IS_NOWHERE value
- introduce ENV_IS_IN_DEVICE
END
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case of several environment location support, env_get_location
is needed to select the correct location depending of the boot
device .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to :
- select the current device to save the environment file
- select the correct EXT4 boot device instance
and partition to save the environment file.
For EXT4, device is mmc, device instance is 0 for sdcard or 1 for eMMC.
The partition is set to "auto" to select the first partition with
bootable flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch configure the default value for mtdids and mtparts
dynamically according the presence of nor and nand in
the board device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Avenger96 board from Arrow Electronics based on STM32MP157
MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards
family and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is needed to make ethernet work on stm32f746-eval which
uses MII mode.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In order to insure that hog GPIOs are configured early during
the boot process, force all pinctrl driver probing in board_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
