Convert the board to DM I2C and DM RTC. This leads to removal of board
side iomuxc configuration, which is now done using pin control driver,
and conversion of board side legacy I2C accessors to DM ones.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Before this commit device tree selection could rely solely on
differentiating the iMX6 processor variant Q and DL. After adding two new
carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs
makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02,
dhcom-picoitx or dhcom-pdk2) at compile time using
CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add a u-boot dtsi for configuring the FEC node of the DH DRC02.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add a u-boot dtsi for configuring the FEC node of the DH picoITX.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Firstly the FEC can now use the regulator reg_eth_vio from
imx6qdl-dhcom-som.dtsi instead of defining its own.
Secondly the &fec node is moved to the more generic SoM device tree
file, because it can be used by multiple boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Use phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from
board header. This is required, because the DH picoITX and DRC02 boards
require different settings than PDK2. The corresponding 'phy-handle'
device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH picoITX device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH DRC02 device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The upstream DT regulators node subnodes are named BUCKn and LDOn,
the downstream DT regulators node subnodes are named buckn and ldon,
add the upstream match.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the preloader_console_init() call after spl_early_init() to avoid
board hang in SPL.
While at it remove explicit in-code console/debug UART pinmuxing (uart1
and its pinmuxing are already marked as u-boot,dm-spl via device tree).
Fixes: 4551e18987 ("configs: verdin-imx8mm: verdin-imx8mp: enable dm serial")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <festevam@denx.de>
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <festevam@denx.de>
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
If the fitImage has some bad block in fit image area, the
offset must be recalulcated. This should be done always.
After implementing it in mxs now is possible to call the function
even for that platform.
Cc: Fabio Estevam <festevam@gmail.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The badblock should be skipped properly in reading and writing.
Fix the logic. The bcb struct is written, skipping the bad block,
so we need to read using the same logic. This was tested create
bad block in the area and then flash it and read it back.
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The specific implementation was having bug. Those bugs are since
the beginning of the implementation. Some manufactures can already
experience this bug in their SPL code. This bug can be more visible on
architecture that has complicated boot process like imx8mn. Older
version of uboot can be affected if the bad block
appear in correspoding of the beginning of u-boot image. In order to
adjust the function we scan from the first erase block.
The problematic part of old code was in this part:
while (is_badblock(mtd, offs, 1)) {
page = page + nand_page_per_block;
/* Check i we've reached the end of flash. */
if (page >= mtd->size >> chip->page_shift) {
free(page_buf);
return -ENOMEM;
}
}
Even we fix it adding increment of the offset of one erase block size
, we don't fix the problem, because the first erase block where the
image start is not checked. The code was tested on an imx8mn where
the boot rom api was not able to skip it. This code is used by other
architecures like imx6 and imx8mm
Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Move the hook after nand_scan_tail is called. The hook must be replaced
to the mxs specific one but those must to be assignment later in the
probe function.
With this fix markbad is working again. Before this change:
nand markbad 0xDEC00
NXS NAND: Writing OOB isn't supported
NXS NAND: Writing OOB isn't supported
block 0x000dec00 NOT marked as bad! ERROR 0
Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
implement get f/w version api.
print ele f/w version in spl.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Select the CMD_UNZIP option so that the 'gzwrite' command
can be used to flash wic.gz image into the eMMC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
pinctrl_wdog as u-boot,dm-spl already marked in imx8mm-verdin-u-boot.dtsi,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move some common changes to imx8mq-u-boot.dtsi, so others could reuse it
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 61cf225053 ("board: gateworks: gw_ventana: use comomn GSC driver")
moved to the common GSC driver and moved remaining board-specific
functions to eeprom.c. The functions in gsc.c are no longer used and it
was removed from the Makefile but the file itself was not removed.
Remove it now.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The uart2 and its pinmux are already marked with u-boot,dm-spl but we
need to move the call to preloader_console_init() after spl_early_init()
to avoid a board hang as dm can't be used until after spl_early_init()
due to the uart driver not enabling the uart clock.
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX8MP SoC FEC needs to have the FEC_QUIRK_ENET_MAC defined.
Fixes: commit 2395625209 ("board: gateworks: venice: add imx8mp-venice-gw740x support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.
There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
All i.MX8M needs TZASC ID SWAP set and locked, no need the check to
waste cpu cycles.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
To i.MX8, M core stack is pre-coded in source code, so need to get it
before kicking M core. The stack pointer is stored in the first word of
the first PT_LOAD section __isr_vector. So use a num to index the
section loading.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
