This change makes debugging a bit easier as the output is better
readable with the added space. The explicit le16_to_cpu() is not
needed in the output. Also this patch moves the strings into one line
to make the patch checkpatch clean.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Accessing the xHCI controller registers should be done via the
xhci_readl/writel functions. This patch adds this to a few missing
places.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
When flush cache of the current GPD and resume QMU, the controller
will try to access the next GPD after processing the current one,
if not flush the next GPD, the controller may get wrong GPD status.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
All debug messages from ep0.c except a few are printed by dbg_ep0() macro.
So for remaining few exceptions use also dbg_ep0() instead of serial_printf().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If we do not set FIFO buffer address and size for some endpoint which is in
use then default programmed address 0x0 would be used which is in conflict
with address of FIFO buffer for endpoint 0. Moreover address of FIFO buffer
for endpoint 0 cannot be programmed, it is fixed to 0x0. Sharing address
space between more endpoints cause data loss and unexpected errors.
This patch is fixing transmission of characters over usbtty serial console
and allows using of usbtty for debugging purposes on Nokia N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Interrupt for EP0 is indicated in intrtx register via first bit. This bit
is set for both RX and TX despite register has only TX in its name. First
bit in intrrx register is reserved, not used and never set.
So remove calling musb_peri_ep0() function at every iteration of udc_irq()
and musb_peri_rx() and call it only from musb_peri_tx() when correct
interrupt bit in initrtx it set.
Address from SET ADDRESS command must be set to faddr register only after
acknowledging SERV_RXPKTRDY followed by received EP0 interrupt. So prior
calling musb_peri_ep0_set_address() check for EP0 interrupt instead of
(incorrect) MUSB_INTR_SOF interrupt.
This patch fixes issue that host (computer) cannot register U-Boot USB
device and is failing with errors:
usb 1-1: new full-speed USB device number 86 using xhci_hcd
usb 1-1: Device not responding to setup address.
usb 1-1: Device not responding to setup address.
usb 1-1: device not accepting address 86, error -71
U-Boot was writing address to faddr register too early and did not wait for
correct interrupt after which should update address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If musb_peri_rx_ep() was called to process received HW buffer but U-Boot
cannot read it yet (e.g. because U-Boot SW buffer is full) then interrupt
was marked as processed also when HW buffer stayed unprocessed.
U-Boot tried to process this buffer again when it received interrupt again,
but it can receive it only when sender (host) sends a new data. As sender
(host) is not going to send a new data until U-Boot process current data
this issue caused a deadlock in case sender (host) is emitting data faster
than U-Boot can process it.
Reading musb intrrx register automatically clears this register and marks
interrupt as processed. So to prevent marking interrupt in U-Boot as
processed, adds a new variable pending_intrrx which would contain
unprocessed bits of intrrx register.
For a second step, every time when musb_peri_rx_ep() is called and there
are waiting data to be processed (signaled by MUSB_RXCSR_RXPKTRDY) either
acknowledge sender (via musb_peri_rx_ack()) that whole HW buffer was
processed or set corresponding bit in pending_intrrx that HW buffer was not
fully processed yet and next iteration is required after U-Boot allocates
space for reading HW buffer.
This patch fixes receiving large usb buffers, e.g. file transfer via Kermit
protocol implemented by 'loadb' U-Boot command over usbtty serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If udc_endpoint_write() was called with bigger payload which does not fit
into one USB packet it is needed to transmit payload in more USB packets.
First packet is transmitted by udc_endpoint_write() call itself and other
packets are put into waiting queue.
Implement function musb_peri_tx() which checks if endpoints are ready for
transmit and continue transmission of waiting queue.
This patch fixes sending big output from printenv command over usbtty
serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>>
PERI_RXCSR is 16bit register so store its value into 16bit local variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch fixes configuring FIFOs for one-directional endpoints which have
only one queue (either RX or TX, but noth both).
Size of FIFO buffer is 2^(idx+3) bytes and starting address is 2^(addr+3).
Moreover first 64 bytes are reserved for EP0.
Without this patch if FIFO size specified by caller was zero then idx was
incorrectly calculated (expr. ffs(0)-1) and size overflowed in fifosz
register. This register uses has only 4 bits for FIFO size. Moreover
specifying zero buffer size is not possible (with idx=0 is minimal buffer
size 8 bytes).
So even for one-directional endpoints we need to correctly specify both
(RX and TX) FIFO buffer sizes and its addresses.
This patch is fixing calculation of start address and buffer size to
minimal value and ensures that it would not overlap with buffer reserved
for EP0.
This issue caused loose of packets on USB bus in both directions and
basically usbtty was unusable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Without this patch clearing was done only when U-Boot was compiled with
MUSB Host Controller. But clearing of data toggle bit is needed also for
MUSB Device Controller otherwise Device Controller does not work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
So far we've been content with passing physical addresses when
configuring memory addresses into XHCI controllers, but not all
platforms have buses with transparent mappings. Specifically the
Raspberry Pi 4 might introduce an offset to memory accesses incoming
from its PCIe port.
Introduce xhci_virt_to_bus() and xhci_bus_to_virt() to cater with these
limitations, and make sure we don't break non DM users.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: fix compilation for 32 bit]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
fix from nicolas
The PCIe bus the controller is connected to might need to be removed
prior the handover. Make sure xhci-pci is also removed so as to avoid
unexpected timeouts or hangs.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Linux kernel v5.7-rc1 introduced the compatible "st,stm32mp15-hsotg".
See Linux kernel commit d49850110434 ("dt-bindings: usb: dwc2: add
support for STM32MP15 SoCs USB OTG HS and FS")
This patch updates the supported compatible in DWC2 driver,
removes the add-on done in U-Boot dtsi and keeps the compatible
defined in SOC dtsi arch/arm/dts/stm32mp151.dtsi:
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Testing with v2021.01 on MIPS Octeon has shown, that the latest patch
for the "short packet event trb handling" did introduce a bug on
platforms with virtual address != physical address. This patch fixes
this issue by using the correct address types in the compare (both
physical in this case).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Ran Wang <ran.wang_1@nxp.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Function dm_pci_map_bar() may fail and returns NULL. Check this to prevent
dereferencing a NULL pointer.
In xhci-pci this may happen when board does not enable CONFIG_PCI_PNP and
PCI_BASE_ADDRESS_0 contains unconfigured zero address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support to disable specific ports, it's useful for some
scenarios:
1. usb3 PHY is shared whith PCIe or SATA, the corresponding
usb3 port can be disabled;
2. some usb2 or usb3 ports are not used on special platforms,
they should be disabled to save power.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If one of functions is not super speed capable, we need force the udc
to be high speed, this is an equivalent implementation of
usb_gadget_udc_set_speed() in kernel but simple, which set the gadget
max_speed to be high speed, so afterwards when start gadget duc can
set the HW to be USB 2.0 mode.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set its max_speed to be super speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add super speed EP config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is to add usb gadget super speed support in common
driver, including BOS descriptor and select the super speed
descriptor from function driver.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Always use the new added config for os_desc_config to fix cdev->
os_desc_config may miss set in case we restart usb gadget driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current way to set cdev->os_desc_config is wrong if user restart
fastboot, as the old config is not used anymore and new allocated
usb_configuration will be used, so set the os_desc_config while
usb_add_config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add device interface GUID for Microsoft Extended Properties Feature
Descriptor.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a proting patch from linux kernel: 37a3a533429e
("usb: gadget: OS Feature Descriptors support"), the original commit
log see below:
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors"."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As other users may use utf8_to_utf16le() to convert the utf8
to utf16 for usb, so move it to head file.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a porting patch from linux kernel: 19824d5eeece
("usb: gadget: OS String support"), original commit log
see below:
"There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As the SDP protocol use the predefined ep num for communication, we can't
change its name hence reset its ep num while do ep autoconfig, this is
only apply for SPL.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since some new fields in usb_ep structure been moved to usb_ss_ep.
The CDNS3 gadget driver should replies on this operation to bind the
usb_ss_ep with the endpoint descriptor when function layer uses
usb_ep_autoconfig to add endpoint descriptors to gadget. So that
CDNS3 driver can know the EP information and configure the EP once
the set configuration request is received.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Each array is used only in one file (core.c or ep0.c). Move their content
to correct file, mark them as static and do not export out of current file.
This change allows to decrease size of u-boot.bin as more of those strings
are not used.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to
ensure that the potential changes to the 'dfu_alt_info' environment
variable are applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In case of usb_add_function() failure the error path has an issue,
i.e the global pointer variable is assigned to garbage
Fix the above mentioned issue by assigning pointer to NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In case of usb_add_function() failure the error path has two issues:
- the potentially allocated structure isn't getting freed
- the global pointer variable is assigned to garbage
Fix the above mentioned issues by freeing memory and assigning NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Casting 32bit int value directly into 64bit unsigned type causes
wrong value for file size equal or larger than 2GB. Fix the wrong
file size by casting uint32_t first.
Fixes: commit 1fe9ae76b1 ("gadget: f_thor: update to support more than 4GB file as thor 5.0")
Reported-by: Junghoon Kim <jhoon20.kim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Now that there is only one sequence number (rather than both requested and
assigned ones) we can simplify this function. Also update its caller to
simplify the logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new sequence number in all cases. Since all devices are assigned
a number when bound, this hack should not be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This hack cannot work in the new sequence-numbering scheme. Remove it
while we wait for the maintainer to complete DM conversion as noted in
the existing comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the redundant setting for USB_RX_EARLY_SIZE. Besides, for
RTL8153B, it is necessary to notify the hardware of the changes
of the aggregation settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
The r8152_eth_probe() may allocate a memory for ss->dev_priv.
It has to be freed if r8152_eth_probe() fails finally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
For bulk IN transfer, the codes will set ISP flag to request event TRB
being generated by xHC for the case of short packet. So when encountering
buffer-cross-64K-boundary (which we will divide payload and enqueuqe
more than 1 transfer TRB), and the first TRB ends up with a short packet
condition it will trigger an short packet code transfer event per that
flag and cause more than 1 event TRB generated for this transfer.
However, current codes will only handle the first transfer event TRB
then mark current transfer completed, causing next transfer
failure due to event TRB mis-match.
Such issue has been observed on some Layerscape platforms (LS1028A,
LS1088A, etc) with USB ethernet device.
This patch adds a loop to make sure the event TRB for last transfer TRB
has been handled in time.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use generic Synopsys DesignWare 3 driver on Intel Edison.
For now it's just a stub which allows future refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
dwc3_meson_g12a_force_mode() sets the dr-mode of the USB PHY. However
it skips setting the mode if it matches the one done during driver probe
(stored in private structure). This fails if the mode has been changed
to other value and then back to initial one. Fix this by configuring the
dr-mode always, regadless of the one set at the driver probe).
This fixes operation of USB gadget based drivers when they are initialized
for the second time.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fix up the code style for those declarations that should now fit onto one
line, which is all of them that currently do not.
This is needed for dtoc to detect the structs correctly, at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
If CONFIG_PHY is not enabled then the dwc3_setup_phy()
returns ENOTSUPP which can be still valid and intentional
so modify error check to handle this -ENOTSUPP.
The same error handling exists in drivers/usb/host/xhci-dwc3.c already
added by commit d648a50c0a ("dwc3: move phy operation to core.c").
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On some board, the ID pin is not connected so the B session must be
overridden with "u-boot,force_b_session_valid" but the VBus sensing
must continue to be handle.
To managed it, this patch adds a new DT field
"u-boot,force-vbus-detection" to use with "u-boot,force_b_session_valid"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add an entry in usb_gadget_controller_number() for the MTU3
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the MediaTek USB3 DRD controller,
its host side is based on xHCI, this driver supports device mode
and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
There is only declaration of usb_speed_string(), but no definition,
so add it to avoid build error when call it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In buffer DMA mode, gadget should re-configure EP 0 to received SETUP
packets when doeptsiz.xfersize is equal to a setup packet size(8 bytes)
and EP 0 is in WAIT_FOR_SETUP state.
Since EP 0 is not enabled in WAIT_FOR_SETUP state, SETUP packets is NOT
received from RxFifo and wriiten to the external memory.
Signed-off-by: Chance.Yang <chance.yang@vatics.com>
This driver doesn't use DM (in the correct places), so we use a device and
not a udevice. We also need to include device_compat.h
Signed-off-by: Sean Anderson <seanga2@gmail.com>
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
-----BEGIN PGP SIGNATURE-----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=v+p3
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-10-07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mips: octeon: add support for DDR4 memory controller
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
This patch adds the glue layer for the MIPS Octeon SoCs. It's ported
mainly from the Linux code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Octeon uses mapped addresses for virtual and physical memory. It's not
that easy to calculate the resulting addresses here. So let's remove
this BUG_ON() completely, as it's not really helpful.
Please also note, that BUG_ON() is not recommended any more in the Linux
kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
On MIPS platforms, mapping of the base address is needed. This patch
switches from dev_get_addr() to dev_remap_addr() to get the mapped base
address of the xHCI controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The R8A774A1 is compatible with the generic rcar-gen3-xhci controller.
This patch adds the compatibility flag, to support the xHCI controller.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Use readx_poll_sleep_timeout() to poll the register status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use macros with parameter to fill ep_info2, then some macros
for MASK and SHIFT can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use TRB_TX_TYPE() instead of (TRB_DATA_OUT/IN << TRB_TX_TYPE_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For normal TRB fields:
use TRB_LEN(x) instead of ((x) & TRB_LEN_MASK);
and use TRB_INTR_TARGET(x) instead of
(((x) & TRB_INTR_TARGET_MASK) << TRB_INTR_TARGET_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There some vendor quirks for MTK xHCI 0.96 host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reserved
DWs of slot context and endpoint context.
2. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Porting from the Linux:
c840d6ce772d("xhci: create one unified function to calculate TRB TD remainder.")
124c39371114("xhci: use boolean to indicate last trb in td remainder calculation")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a member to save xHCI version, it's used some times.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This driver does not use DM, so we need to use a struct device instead of a
struct udevice. Not ideal, but it'll have to do for now.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This can conflict with asm/io.h on some archs, and it isn't needed to build
dwc3-generic.c
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This driver does not use DM, so use log_xxx instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This logs with the device from struct dwc3. Some files also need to include
dm.h so fields in udevice can be accessed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a dev argument to some functions so dev_xxx always has a device
to log with. In one instance we must use use a different log function when
we are compiled without DM_USB.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
ep0.c also need to include dm.h so dev_xxx can access udevice fields.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
This is follow up patch based on commit 664e16ce99 ("xilinx: kconfig:
Change Kconfig dependencies for Xilinx drivers").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Lot of Qualcomm SoC-s use DWC3 controller for both USB2.0 and USB3.0
ports.
Qualcomm has some custom config registers on top of the generic ones,
but for host mode these are not needed.
So lets add the neccessary compatible string.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As the error message is now displayed by generic phy functions,
the dev_err/pr_err can be change to dev_dbg/pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the dev_err can be change to dev_dbg.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
It was revealed that when the fastboot_tx_write_str function is called
without the previously initialized fastboot_func->in_req->complete field,
a copy of in_req will be sent to the I/O requests queue without
an initialized field.
Moving a piece of code with the initializing of the
fastboot_func->in_req->complete field above transmit_tx allows to solve
this problem.
Fixes: 65c96757fe "usb: fastboot: Convert USB f_fastboot to shared fastboot"
Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
Since the USB HID limits the maximum bandwidth(3072) for interrupt
endpoint transfers, when the bInterval set to 1, we can only support 3
boards to run sdp at the same time. In order to support more boards,
change the bInterval of interrupt endpoint to 3, which will not affect
the transmission speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
EP0 has been used to transfer file data in sdp before, but the max
packetsize of ep0 is 64 bytes. So in order to improve the file transfer
speed, here add the EP1_OUT interrupt endpoint which max packetsize is
set to 1024 byte.
After testing, it turns out that using ep1out is twice as fast as using
ep0 while receiving data in sdp.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support to f_sdp to search and load iMX8 container image or iMX8M
FIT image by new UUU command SDPV.
When using the SDPV, the uuu will continue to send out data after first
level boot loader used by ROM. This means uuu won't skip to the offset
of the second boot loader, and the padding data before second boot loader
will be sent out. So we have to search the FIT header or container header
in the buffer that SDP received.
Also change to more common method to exit f_sdp handler not depending on
SPL_FIT_FOUND flag because container loader won't set this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the buffer length of sdp usb request is 65, we have to allocate
65 bytes not 64 bytes. Otherwise there is potential buffer overflow.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint,
and the SDP device can send packet with 512 byte size.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
MAX3420 implements FullSpeed USB Device over SPI.
Another version MAX3421, also implements USB Host mode.
This driver should be good for the device mode of max3421 as well.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Android 10 adds support for dynamic partitions and in order to support
this userspace fastboot must be used[1]. New tool fastbootd is
included into recovery.
Userspace fastboot works from recovery and is launched if:
1) - Dynamic partitioning is enabled
2) - Boot control block has 'boot-fastboot' value into command field
The bootloader is expected to load and boot into the recovery image
upon seeing boot-fastboot in the BCB command. Recovery then parses the
BCB message and switches to fastbootd mode[2].
Please note that boot script is expected to handle 'boot-fastboot'
command in BCB and load into recovery mode.
Bootloader must support 'reboot fastboot' command which should reboot
device into userspace fastboot to accomodate those changes[3].
Another command that bootloader must support[3] is 'reboot recovery'. This
command should simply reboot device into recovery mode.
[1] - https://source.android.com/devices/bootloader/fastbootd
[2] - https://source.android.com/devices/bootloader/fastbootd#unified_fastboot_and_recovery
[3] - https://source.android.com/devices/bootloader/fastbootd#modifications_to_the_bootloader
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
When unregister gadget driver in ci_udc, the usb device is not
removed or stop. This causes next "usb start" fails to work.
Add a new interface "usb_remove_ehci_gadget" in usb-uclass to
remove the usb device for DM driver. Using "usb_lowlevel_stop" for
non-DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The usb mass storage (f_mass_storage.c) uses fixed usb index 0,
this causes problem while CDNS3 USB controller index is 1.
Modify the API of fsg to pass the controller index.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The original rtl_clear_bp() is used to clear the firmware of both
PLA and USB MCU. The new one could clear the firmware of PLA or
USB independently. It is unnecessary to clear firmware, if there
is no one to be updated.
Besides, clear the firmware by writing the relative registers in
bulk.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reset bmu after disabling Tx/Rx. This is used to clear the FIFO of
Tx/Rx. The remained data may be transferred after Tx/Rx is re-enabled.
And it results in garbage data.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
The indentation was messing up with the scripts/build-whitelist.sh that
was marking SYS_USB_EVENT_POLL_VIA_INT_QUEUE (and probably also the
other indented options) erroneously as ad-hoc configure option with the
following error:
```
Error: You must add new CONFIG options using Kconfig
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE
```
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add wait_event_timeout - sleep until a condition gets true or a
timeout elapses.
This is a stripped version of the same from Linux kernel with the
following u-boot specific modifications:
- no wait queues supported
- use u-boot timer to detect timeouts
- check for Ctrl-C pressed during wait
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop atomic_read from gadget/ether.c as this has existed for a
while and now causes problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
Port hypervisor related code from Mini-OS. This is referencing the code
of Mini-OS from [1] by Huang Shijie and Volodymyr Babchuk which is for
ARM64.
Update essential arch code to support required bit operations, memory
barriers etc.
Copyright for the bits ported belong to at least the following authors,
please see related files for details:
Copyright (c) 2002-2003, K A Fraser
Copyright (c) 2005, Grzegorz Milos, gm281@cam.ac.uk,Intel Research Cambridge
Copyright (c) 2014, Karim Allah Ahmed <karim.allah.ahmed@gmail.com>
[1] - https://github.com/zyzii/mini-os.git
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop wmb() from musb-net/linux-compat.h now]
Signed-off-by: Tom Rini <trini@konsulko.com>
node varaible is used as iterator into ofnode_for_each_subnode()
loop, when exiting of it, node is no more a valid ofnode.
Use dwc3_node instead as parameter of ofnode_valid()
Fixes: ac28e59a57 ("usb: Migrate to support live DT for some driver")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Some platforms, like MIPS Octeon, use mapped addresses (virtual address
!= physical address). On these platforms we need to make sure, that the
local virtual addresses are converted to physical (DMA) addresses for
the xHCI controller. This patch adds the missing virt_to_phys() calls,
so that the correct addresses are used.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
These values are already swapped to CPU endianess, so swapping them
again is a bug. Let's remove the swap here instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
xhci_writeq() makes the CPU->LE swapping only when addressing registers
in the xHCI controller address range and not in the local memory (RAM).
We need to use cpu_to_le64() here to ensure that the conversion is done
correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
While trying to use the U-Boot xHCI driver on the MIPS Octeon platform,
which is big endian, I noticed that the driver is missing a few endian
conversion calls. This patch adds these missing endian conversion
calls.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Also move the inline function out into a C file. We should not include C
code in headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Some atypical users of xhci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[mb: squash fix to only build xhci_reset_hw() if CONFIG_DM_BUS]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In current code there is no cache flush after initializing the scratchpad
buffer array with the scratchpad buffer pointers. This leads to a failure
of the "slot enable" command on the rpi4 board (Broadcom STB PCIe
controller + VL805 USB hub) - the very first TRB transfer on the command
ring fails and there is a timeout while waiting for the command completion
event. After adding the missing cache flush everything seems to be working
as expected.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Update the firmware to improve compatibility for none-intel USB
host controller. The more information is as following.
The device has auto-installed driver feature - via switch CD-ROM/NIC
mode. But in some corner cases, it would switch to CD-ROM unexpected.
This issue results in Lan Function Disabled.
While USB PHY transits to P3 from P0 due to the absent of transmitter
control, it would issues undefined signal to its link partner.
Some Down Stream Port misidentify the undefined signal as wakeup
signal. So the link state will not keep in suspend even the system
is idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
It is possible to specify a device tree node for an USB device. This is
useful if you have a static USB setup and want to use aliases which
point to these nodes, like on the Raspberry Pi.
The nodes are matched against their hub port number, the compatible
strings are not matched for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is defined in the asm/cache.h header file. Update this header file to
include it so it gets the same value consistently across U-Boot.
This fixes 'usb host' on omapl138_lcdk.
Fixes: 90526e9fba ("common: Drop net.h from common header")
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
We have changed to use dwc3 generic driver for usb3.0 host, so the
legacy Rockchip's xHCI driver is not needed, and drop it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller
in resetting to hold pipe power state in P2 before initializing the PHY.
This commit fixed it and added device compatible for rockchip platform.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Print the error code if the regulator enable fails, otherwise the error
message is rather useless and confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
The regulator-fixed would return -ENOSYS when enabled/disabled,
because this operation is not supported, but this is not an error
e.g. on systems where the VBUS cannot be controlled, so if this
is the error code reported by the regulator core, consider it a
success and continue.
Signed-off-by: Marek Vasut <marex@denx.de>
Although I think it never occurs, the code doesn't make sense, because
it may allow to assign an IN endpoint to ss->ep_out.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init
that is convenient for both DM_USB and u-boot traditional process.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Reference from below Linux commit,
commit <b138e23d3dff> ("usb: dwc3: core: Enable AutoRetry feature
in the controller")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate
check quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk")
in Linux Rockchip Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")
in Linux Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The phy_bulk pointer *usb_phys is used before allocated,
fix it by using a phy_bulk variable instead in
xhci_dwc3_platdata struct
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The omap3.dtsi file shows the usbhshost node with two sub-nodes
for ohci and ehci. This patch file creates the usbhshost, and
pulls the portX-mode information. It then locates the EHCI
sub-node, and initializes the EHCI controller with the info
pulled from the usbhshost node.
There is still more to do since there isn't an actual link
between the 'phys' reference and the corresponding phy driver,
and there is no nop-xceiv driver yet.
In the meantime, the older style reference to
CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull
the phy out of reset until the phy driver is completed and the
phandle reference is made.
Signed-off-by: Adam Ford <aford173@gmail.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add a function g_dnl_set_product to change the Product string used in USB
enumeration in any command based on download gadget.
If the function is called with NULL pointer, the product string is set to
the default value (product[] = "USB download gadget").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Xilinx Versal platform uses dwc3 and hence its compatible string
needs to be added to dwc3 glue ids.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Reference from below Linux commit,
commit <00fe081dc3a3> ("usb: dwc3: add dis_del_phy_power_chg_quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add fuse check for USB. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If SDP_WRITE and SDP_JUMP addr is zero, use CONFIG_SDP_LOADADDR
as default address
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use the phy bulk API to get a group of phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Get a group of phys by the phy bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
-----BEGIN PGP SIGNATURE-----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=e10O
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200428' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
dwc3-sti-glue has been broken since MISC uclass has been
modified to scan DT sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Solve issue for the display of "usb start" command on stm32mp1
because one carriage return is missing in DWC2 probe.
Before the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: Bus usbh-ehci@5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: USB DWC2
Bus usbh-ehci@5800d000: USB EHCI 1.00
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK
is not activated the clk function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use generic phy to initialize the PHY associated to the
DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY
is not activated, the generic PHY function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Power on/off the PHYs to enable power to the USB ports, fixing USB support
on Khadas VIM3/VIM3L boards.
The G12A USB complex has at least 2 USB2 PHYs, but one is muxed between the
DWC2 and DWC3 controller and the other one directly connected to the DWC3
controller. The USB3+PCIe combo PHY is muxed between the DWC3 controller
and a DW-PCIE controller.
All PHYs are optional, but it's type (usb2/usb3) and position are important
to determine it's capabilities, thus they are stored in a fixed size
array and the phy-name determines it's position, it's position determining
it's type and functionnalities.
This is why we need to loop over the array to power on all the DT provided
PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
