Commit graph

193 commits

Author SHA1 Message Date
Ira W. Snyder
9839709ea3 mpc85xx: support for Freescale COM Express P2020
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.

Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.

This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 09:07:51 -06:00
Timur Tabi
3e0529f742 powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files.  So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020.  It was already defined for the
P1010 and P1014.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
York Sun
4108508a96 powerpc/85xx: Add workaround for erratum A-003474
Erratum A-003474: Internal DDR calibration circuit is not supported

Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.

Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf54

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Kumar Gala
43f082bb7f powerpc/85xx: Add workaround for erratum CPU-A003999
Erratum A-003999: Running Floating Point instructions requires special
initialization.

Impact:
Floating point arithmetic operations may result in an incorrect value.

Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:05 -06:00
Kumar Gala
50cf3d17ce powerpc/85xx: Add support for Book-E MMU Arch v2.0
A few of the config registers changed definition between MMU v1.0 and
MMUv2.0.  The new e6500 core from Freescale implements v2.0 of the
architecture.

Specifically, how we determine the size of TLB entries we support in the
variable size (or TLBCAM/TLB1) array is specified in a new register
(TLBnPS - TLB n Page size) instead of via TLBnCFG.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:36:51 -06:00
Timur Tabi
5c4a3d431e powerpc/85xx: fix definition of MAS register macros
Some of the MAS register macros do not protect the parameter with
parentheses, which could cause wrong values if the parameter includes
operators.

Also fix the definition of TSIZE_TO_BYTES() so that it actually uses
the parameter.  This hasn't caused any problems to date because the
parameter was always been 'tsize'.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:57 -06:00
chenhui zhao
aada81de70 powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.

Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:32 -06:00
Joe Hershberger
7d6a098219 mpc83xx: Cleanup usage of LBC constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
4713db666c mpc83xx: Fix ipic structure definition
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>

Added siprr_{b,c} and sepcr for completeness.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Kim Phillips
63063cc7ae mpc83xx: fix global timer structure definition
The byte address distance between GTCFR2 and GTMDR1 is 11, not 10.

Reported-by: Shawn Bai <programassem@hotmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:51 -05:00
Anton Staaf
0991701a27 powerpc: cache: define ARCH_DMA_MINALIGN for DMA buffer alignment
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
2011-10-23 20:50:42 +02:00
Anatolij Gustschin
c4c9fbebae consolidate mdelay by providing a common function for all users
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:16:08 +02:00
Kyle Moffett
710308ee18 mpc85xx: Add inline GPIO acessor functions
To ease the implementation of other MPC85xx board ports, several common
GPIO helpers are added to <asm/mpc85xx_gpio.h>.

Since each of these compiles to no more than 4-5 instructions it would
be very inefficient to call them out of line, therefore we put them
entirely in the header file.

The HWW-1U-1A board port which these were written for strongly prefers
to set multiple GPIOs as a single batch operation, so the API is
designed around that basis.

To assist other board ports, a small set of wrappers are used which
provides a standard gpio_request() interface around the MPC85xx-specific
functions.  This can be enabled with CONFIG_MPC85XX_GENERIC_GPIO

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-21 00:04:28 -05:00
Kumar Gala
4d28db8a1e powerpc/85xx: Add support for RMan LIODN initialization
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:48 -05:00
Kumar Gala
1a0c64219d powerpc/85xx: Update setting of SRIO LIODNs
Properly set the LIODN values associated with SRIO controller.  On
P4080/P3060 we have an LIODN per port and one for the RMU.  On
P2041/P3041/P5020 we have 2 LIODNs per port.

Update the tables for all of these devices to properly handle both
styles.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-18 00:36:15 -05:00
Timur Tabi
7f92c3a275 powerpc/p3060: remove all references to RCW bits EC1_EXT, EC2_EXT, and EC3
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-13 23:38:10 -05:00
Xie Xiaobo
ae2044d8b3 powerpc/mpc8536ds: Add eSPI support for MPC8536DS
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
   so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
   to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.

Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-09 17:57:54 -05:00
Timur Tabi
3038171628 powerpc/85xx: fix null pointer dereference when init the SGMII TBI PHY
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.

During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used.  In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.

We also need to define the PHY registers in struct fm_mdio.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-09 17:57:53 -05:00
Mike Frysinger
e2a53458a7 net: drop !NET_MULTI code
This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Mike Frysinger
476af299b0 image: push default arch values to arch headers
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.

Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:15 +02:00
Valentin Longchamp
79843950b2 POST: add post_log_res field for post results in global data
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.

An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-10-05 22:03:10 +02:00
Graeme Russ
9558b48af0 console: Implement pre-console buffer
Allow redirection of console output prior to console initialisation to a
temporary buffer.

To enable this functionality, the board (or arch) must define:
 - CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
 - CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
 - CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)

The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
2011-10-05 22:03:09 +02:00
Shengzhou Liu
6d7b061af1 powerpc/p3060: Add SoC related support for P3060 platform
Add P3060 SoC specific information:cores setup, LIODN setup, etc

The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 09:36:28 -05:00
Kumar Gala
6b3a8d0086 powerpc/85xx: Add support for setting up RAID engine liodns on P5020
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020.  Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ).  This just handles RAID Engine in non-DPAA mode.

Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Kumar Gala
2b3a1cdd9e powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].

Refer to the erratum LBIU3 of mpc8548.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Kumar Gala
5ace2992b5 powerpc/mpc8548: Add workaround for erratum NMG_DDR120
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.

Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
Ruchika Gupta
7065b7d466 powerpc/p4080: Add support for secure boot flow
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
   (Please note that ISBC expects all these addresses, images to be
    validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
   at 0xcffffffc.

Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
   CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
   (The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
    created by PBL/configuration word within 0 - 3.5G memory range. The
    u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
   PBL/configuration word after switch to AS = 1

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
York Sun
d29d17d7ba powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.

To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.

Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
York Sun
4e57382faa powerpc/mpc8xxx: Add DDR2 to unified DDR driver
DDR2 has different ODT table and values. Adding table according to Samsung
application note.

Fix additive latency calculation to avoid interger underflow.

Also converted typedef dynamic_odt_t to struct dynamic_odt.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
York Sun
cae7c1b56b powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
Kumar Gala
a598643267 powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors.  The most
significant bit is used as a mfg code on MPC8536.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Roy Zang
fe1a1da038 powerpc/85xx: Add networking support to P1023RDS
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII.  The second can only do SGMII & RGMII.

We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Kumar Gala
c916d7c914 powerpc/85xx: Add support for FMan ethernet in Independent mode
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block.  Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman).  However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.

Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely.  This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.

Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.

We add support for the following SoCs:
 * P1023 - 1 Fman, 2x1g
 * P4080 - 2 Fman, each Fman has 4x1g and 1x10g
 * P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Timur Tabi
fbb9ecf749 powerpc/mp: add support for discontiguous cores
Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more.  We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Poonam Aggrwal
bc6bbd6be8 fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.

Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.

Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
fb855f43a1 powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.

Impact:
Boot from IFC may not be successful if IFC_CS3 is used.

Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
42aee64bd9 fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size

Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data

Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Dipen Dudhat
52f90dad60 nand: Freescale Integrated Flash Controller NAND support
Add NAND support (including spl) on IFC, such as is found on the p1010.

Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC.  UBI should
work, as it does not use OOB for anything but ECC.

When hardware ECC is not enabled in CSOR, software ECC is now used.

Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-09-29 19:01:04 -05:00
Timur Tabi
e46fedfeb2 powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot).  All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Kumar Gala
b6c3722dfa powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Ramneek Mehresh
1b719e6654 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
 - Use both getenv() and hwconfig to get USB phy type till getenv()
   is depricated
 - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
   has internal UTMI phy

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Weirich, Bernhard
25fb02abdf Fix incorrect array size of phy settings for 405EX
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.

Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-09-19 11:51:21 +02:00
Kumar Gala
8992738db7 powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500
At some point we broke the detection of e500v1 class cores.  Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Stephen George
f110fe940c powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.

Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:37 -05:00
Mike Williams
1626308797 cleanup: Fix typos and misspellings in various files.
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
2011-07-28 21:27:36 +02:00
Becky Bruce
9cdfe28106 powerpc/mpc85xx: Add clear_ddr_tlbs function
This is useful when we just want to wipe out the TLBs.  There's currently
a function that resets the ddr tlbs to a different value; it is changed to
utilize this function.  The new function can be used in conjunction with
setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address
range as needed.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-22 03:07:47 -05:00
York Sun
23f9670f1a powerpc/mpc8xxx: Allow override DDR read-to-write turnaround time
Add this option to allow boards to override the default read-to-write
turnaround time for better performance.

Signed-off-by: York Sun <yorksun@freescale.com>
2011-07-11 13:24:20 -05:00
Felix Radensky
aeb6716a12 powerpc/85xx: Fix pin muxing for second USB controller
On P1022/P1013 second USB controller is muxed with second
Ethernet controller. The current code to enable second USB
fails to properly clear pinmux bits used by ethernet. As a
result, Linux freezes when this controller is used. This
patch fixes the problem.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
York Sun
51d498f175 powerpc/mpc8xxx: Add 16-bit support for DDR3
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit
DDR devices.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Kumar Gala
1f97987a51 powerpc/85xx: Add P2041 processor support
The P2041 is similar to P2040, however has a 10G port and backside L2

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:19 -05:00