In Infineon multi-die package parts, we need to use Read Any Register op
to read status register in 2nd or further die. Infineon S28HS02GT is
dual-die package and supports Octal DTR interface. To support this,
spansion_read_any_reg() needs to be reworked. Implementation is similar
to existing read_sr() that already supports Octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation encounters issues when testing data ranging
from 0 to 8 bytes. This was confirmed through testing with both ISSI
(IS25WX256) and Micron (MT35XU02G) Flash exclusively in SDR mode.
Upon investigation, it was observed that utilizing the
"SPI_NOR_OCTAL_READ" flag and attempting to read less than 8 bytes in
STIG mode results in a read failure, leading to a compare test failure.
To resolve this issue, the CMD_4BYTE_FAST_READ opcode is now utilized
instead of CMD_4BYTE_OCTAL_READ, specifically in SDR mode.
This is based on patch series:
https://lore.kernel.org/all/cover.1701853668.git.tejas.arvind.bhumkar@amd.com/
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Added support for the ISSI OSPI flash part IS25LX512M.
Initial testing was performed on the Tenzing-se1 board using
SDR mode, covering basic erase, write, and readback operations.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If even one byte is lost due to Rx FIFO overflow then we will never
exit the read loop. Because the (priv->rx != priv->rx_end) condition will
be always true.
Let's check if Rx FIFO overflow occurred and exit the read loop
in this case.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Drop leading space in front of a comment. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Include missing asm/arch/rmobile.h in board/renesas/rcar-common/v3-common.c
to prevent build failure of r8a77970_eagle r8a779a0_falcon r8a77980_v3hsk
and r8a77970_v3msk .
Include missing asm/u-boot.h in falcon.c and grpeach.c to fix build failure
due to missing definition of struct bd_info . Include errno.h in grpeach.c
to fix build error due to missing definition of EINVAL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
* Add missing field to SMBIOS type 2 structure definition
* Provide smbios command to display smbios table
* Enable the command on sandbox and qemu_arm64_defconfig
* Provide a python test for the smbios command
* Fix copying SMBIOS 2.1 table from QEMU
* Correct EFI TCG measurement to assume SMBIOS 3 table
-----BEGIN PGP SIGNATURE-----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=jv3i
-----END PGP SIGNATURE-----
Merge tag 'smbios-2024-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request smbios-2024-04-rc1-2
* Add missing field to SMBIOS type 2 structure definition
* Provide smbios command to display smbios table
* Enable the command on sandbox and qemu_arm64_defconfig
* Provide a python test for the smbios command
* Fix copying SMBIOS 2.1 table from QEMU
* Correct EFI TCG measurement to assume SMBIOS 3 table
As we support installing SMBIOS3 tables in U-Boot we need to add this GUID
to the translation table used buy uuid_guid_get_str().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The current code convert the SMBIOS 2.1 entry point structure to
SMBIOS 3.0 entry point structure. The max_struct_size member in
SMBIOS 2.1 entry point structure indicates
"Size of the largest SMBIOS structure, in bytes".
We need to use struct_table_length instead.
Fixes: 1c5aab803c ("smbios: copy QEMU tables")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Current U-Boot only supports the SMBIOS 3.0 entry point structure.
TCG2 measurement code should migrate to SMBIOS 3.0 entry
point structure.
efi_selftest tcg2 test also needs to be updated, and expected
PCR[1] result is changed since guid for SMBIOS EFI system table
uses different guid SMBIOS3_TABLE_GUID instead of SMBIOS_TABLE_GUID.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have a Python test the copying of SMBIOS tables from QEMU.
To make use of the test we need the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
To make use of the Python smbios test we need the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a unit test for the smbios command.
Provide different test functions for QEMU, sandbox, and other systems.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a man-page for the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
U-Boot can either generated an SMBIOS table or copy it from a prior boot
stage, e.g. QEMU.
Provide a command to display the SMBIOS information.
Currently only type 1 and 2 are translated to human readable text.
Other types may be added later. Currently only a hexdump and the list of
strings is provided for these.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The type 2 structure must include information about the contained objects.
It is fine to set the number of contained object handles to 0.
Add the missing field.
Fixes: 721e992a8a ("x86: Add SMBIOS table support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Additionally test a UTF-8 string where each code point translates to three
UTF-8 bytes.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As we have had this file for a while now, we should include installing
and populating our pip cache from here as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
In case CONSOLE_MUX and SYS_CONSOLE_IS_IN_ENV are on and
stdin or stdout or stderr are missing in environment, as fallback, get
these either from stdio_devices[std] or stdio_devices[std]->name.
Fixes: 6b343ab38d ("console: Print out complete stdio device list")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
It seems that the U-Boot console entry of the bootmenu has lost
its original meaning. Now, even if it is chosen, the probability
that you will enter the actual U-Boot console is quite low.
Boot env, bootflow, bootcommand script may appear, but not the
actual console. Hence, let's remove ambiguity and name this
entry by what it actually does: 'Exit' the bootmenu.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Speed grade T requires the VDD_CORE voltage to be 0.85V if using
the maximum core frequency.
Speed grades G, K, S allow the VDD_CORE voltage to be 0.75V up to the
maximum core frequency but allow to run at 0.85V.
For efficiency in manufacturing and code maintenance we use 0.85V for
the PMIC defaults and device tree settings and dynamically adjust the
voltage in the PMIC and device tree to 0.75V for lower speed SKU to
gain more than 100mW power consumption reduction.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Add two functions, one which returns the SoC speed grade and one
which returns the SoC operating temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
mach-k3/am625_fdt.c does fdt fixup depending on fields in the device
identification register. Move the accessors to the device identification
register as inline functions into the am62_hardware.h header, so that
they can be used for other functionality.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
These headers follow the pattern:
| #if CONFIG_IS_ENABLED(FANCY_FEATURE)
| void foo(void);
| #else
| static inline void foo(void) { return -ENOSYS; }
| #endif
In the #else path ENOSYS is used, however linux/errno.h is not included.
If errno.h has not been included already the compiler errors out even
if the inline function is not referenced.
Make those headers self contained.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The value of CONFIG SYS_MAXARGS limits the usability of the 'for' command.
The current default of 16 is too low for some use case. Cf.
https://bugs.launchpad.net/snap-core18/+bug/1910094
Increase the default to 64.
Reported-by: Dave Jones <dave.jones@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
EEPROM detection logic in ti_i2c_eeprom_get() involves reading
the total size and the 1-byte size with an offset 1. The commit
9f393a2d7a ("board: ti: common: board_detect: Fix EEPROM read
quirk for 2-byte") that attempts to fix this uses a wrong pointer to
compare.
The value with one offset is read into offset_test, but the pointer
used to match was still ep, resulting in an invalid comparison of the
values. The intent is to identify bad 2-byte addressing eeproms that
get stuck on the successive reads.
Fixes: 9f393a2d7a (board: ti: common: board_detect: Fix EEPROM read quirk for 2-byte)
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
This series results in making it such that with CONFIG_MTD disabled we
then do not prompt the user for a number of memory technology device
related options and so clean up our configuration menu / display.
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
This command is only useful on CFI and NOR type flashes and not others.
Update the dependency so that it's not enabled by default in other
cases. This will lead to a number of platforms no longer building this
command, where it was not useful.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order for our environment to be present on SPI flash we need to
depend not on the symbol for a SPI controller but rather that SPI flash
of some sort is present. Update the dependencies.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than rely on someone selecting or implying this hidden symbol
that the command requires, select it explicitly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This specific bit logic is used to determine what NAND chip is present
on a board in order to then know what revision of the board we have and
so what DDR chips are present. We can only do this if we have a NAND
chip, and so we will have NAND_OMAP_GPMC enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently when a hub is turned on, all the ports are powered on.
This works well for hubs which have individual power control.
For the hubs without individual power control this has no effect.
Mostly in these scenarios the hub port is powered before the USB
controller is enabled, this can lead to some devices in unexpected
state.
With this patch, we explicitly reset the port while powering up hub
This resets the port for hubs without port power control and has
no effect on hubs with port power control as the port is still off.
Before this patch AMicro AM8180 based NVME to USB adapter won't be
detected as a USB3.0 Mass Storage device but with this it works as
expected.
Tested working after this patch:
1. AMicro AM8180 based NVME to USB Adapter
2. Kingston DataTraveler 3.0
3. GenesysLogic USB3.0 Hub
The drives were tested while connected directly and via the hub.
Signed-off-by: Shantur Rathore <i@shantur.com>
Reviewed-by: Marek Vasut <marex@denx.de>
- Allow i.MX8M Plus DHCOM to operate in overdrive mode.
- Allow i.MX8M Plus eDM SBC to operate in overdrive mode.
- Enable the 'kaslrseed' command on DH i.MX8M Plus DHCOM.
- Select LTO by default on i.MX8M.
- Convert pico-dwarf/hobbit-imx6ul to CONFIG_DM_SERIAL.
- Fix 'reset' command on wandboard.
Clearfog GTR connects eth2 / serdes 1 to a 2.5Gbps capable ethernet
switch port. Linux already configures a fixed-link at speed 2500 from
device-tree.
Upgrade serdes 1 rate to 3.125Gbps to support a 2.5Gbps link.
Additionally add comments documenting each serdes' function of clearfog
gtr, which are shared with clearfog pro.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Clearfog GTR has an assembly option for a SATA connector, CON18.
It shares the serdes with mini-pcie connector CON3.
Add new kconfig option to select betweenata and pci, defaulting to pci
as it was previously configured in board-file.
Clearfog GTR connects eth2 / serdes 1 to a 2.5Gbps capable ethernet
switch port. Linux already configures a fixed-link at speed 2500 from
device-tree.
Upgrade serdes 1 rate to 3.125Gbps to support a 2.5Gbps network link on
Clearfog GTR.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Linux 6.6.y with KASLR enabled would print the following message on boot:
"
KASLR disabled due to lack of seed
"
Enable the 'kaslrseed' command so a random number seed can be pulled
from CAAM and inserted into the /chosen node 'kaslr-seed' property of
Linux kernel DT before boot, thus letting KASLR work properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
