When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
There may be multiple PCIe controllers in a SoC.
It is not correct that always calling pci_bus_to_hose(0) to get
the first PCIe controller for the PCIe device connected other
controllers. We just remove this calling because hose always point
the correct PCIe controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
We should use the new address mapping functions unless we are in
compatibility mode. Disable the old functions by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move this function into the compatibility file so that it is not available
by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move these functions into the compatibility file so that they are not
available by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The address range check may overflow if the memory region is located at
the top of the 32-bit address space. This can e.g. be seen on TK1 if
using the E1000 gigabit Ethernet driver where start and size are both
0x80000000 leading to the following messages:
Apalis TK1 # tftpboot $loadaddr test_file
Using e1000#0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.2
Filename 'test_file'.
Load address: 0x80408000
Loading: pci_hose_phys_to_bus: invalid physical address
This patch fixes this by changing the order of the addition vs.
subtraction in the range check just like already done in
__pci_hose_bus_to_phys().
Reported-by: Ivan Mercier <ivan.mercier@nexvision.fr>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
When converting between PCI bus and phys addresses, a two pass search
was introduced with preference to non-PCI_REGION_SYS_MEMORY regions.
See commit 2d43e873a2.
However, since PCI_REGION_MEM is defined as 0, the if statement was
always asserted true: ((flags & PCI_REGION_MEM) == PCI_REGION_MEM)
This patch uses PCI_REGION_TYPE bit to check if the region is
PCI_REGION_MEM: ((flags & PCI_REGION_TYPE) == PCI_REGION_MEM)
Signed-off-by: Cheng Gu <chenggu@marvell.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit aec241d "dm: pci: Use the correct hose when configuring devices"
was an attempt to fix pci bridge device configuration, but unfortunately
that does not work 100%. In pciauto_config_devices(), the fix tried to
call pciauto_config_device() with a ctlr_hose which is supposed to be
the root controller hose, however when walking through a pci topology
with 2 or more pci bridges this logic simply fails.
The call chain is: pciauto_config_devices()->pciauto_config_device()
->dm_pci_hose_probe_bus(). Here the call to dm_pci_hose_probe_bus()
does not make any sense as the given hose is not the bridge device's
hose, instead it is either the root controller's hose (case#1: if it
is the 2nd pci bridge), or the bridge's parent bridge's hose (case#2:
if it is the 3rd pci bridge). In both cases the logic is wrong.
For example, for failing case#1 if the bridge device to config has the
same devfn as one of the devices under the root controller, the call
to pci_bus_find_devfn() will return the udevice of that pci device
under the root controller as the bus, but this is wrong as the udevice
is not a bus which does not contain all the necessary bits associated
with the udevice which causes further failures.
To correctly support pci bridge device configuration, we should still
call pciauto_config_device() with the pci bridge's hose directly.
In order to access valid pci region information, we need to refer to
the root controller simply by a call to pci_bus_to_hose(0) and get the
region information there in the pciauto_prescan_setup_bridge(),
pciauto_postscan_setup_bridge() and pciauto_config_device().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
Also add a comment to explain the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
pci_hose_phys_to_bus() is needed by several drivers. Move it to
pci_common.c to avoid a broken build when CONFIG_DM_PCI is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Driver model will share many functions with the existing PCI implementation.
Move these into their own file to avoid duplication and confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
