The MX25V8035F is a 8Mb SPI NOR flash and the MX25R1635F is very
similar, but has twice the size (16Mb) and supports a wider supply
voltage range.
They were tested on the Kontron Electronics i.MX6UL and i.MX8MM SoMs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Unfortunately the UART driver in current Linux for Armada 3700 expects
UART's parent clock to be XTAL and calculats baudrate divisor according
to XTAL clock. Therefore we must switch back to XTAL clock before
booting kernel.
Implement .remove method for this driver with DM_FLAG_OS_PREPARE flag
set.
If current baudrate is unsuitable for XTAL clock then we do not change
anything. This can only happen if the user either configured unsupported
settings or knows what they are doing and has kernel patches which allow
usage of non-XTAL parent clock.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Using TBG clock as parent clock for UART allows us using higher
baudrates than 230400.
Turris MOX with external FT232RL USB-UART works fine up to 3 MBaud
(which is maximum for this USB-UART controller), while EspressoBIN with
integrated pl2303 USB-UART also works fine up to 6 MBaud.
Slower baudrates with TBG as a parent clock can be achieved by
increasing TBG dividers and oversampling divider. When using the slowest
TBG clock, minimal working baudrate is 300.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Setting DM_FLAG_PRE_RELOC for Armada 3720 clock drivers (TBG and
peripheral clocks) makes it possible for serial driver to retrieve clock
rates via clk API.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to round to closest value, i.e.
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to that returned by
get_ref_clk().
This makes A3720 UART stable at standard UART baudrates between 1800 and
230400.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With gcc-11 we get a multiple errors here as the declarations for
mscc_pinctrl_ops and mscc_gpio_ops are missing an extern.
CC: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc-11 we see:
drivers/ddr/marvell/a38x/ddr3_debug.c:672:47: error: argument 2 of type 'u32[5]' {aka 'unsigned int[5]'} with mismatched bound [-Werror=array-parameter=]
672 | int ddr3_tip_read_adll_value(u32 dev_num, u32 pup_values[MAX_INTERFACE_NUM * MAX_BUS_NUM],
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/ddr/marvell/a38x/ddr3_training_ip_engine.h:10,
from drivers/ddr/marvell/a38x/ddr3_init.h:17,
from drivers/ddr/marvell/a38x/ddr3_debug.c:6:
drivers/ddr/marvell/a38x/ddr3_training_ip_flow.h:116:47: note: previously declared as 'u32[]' {aka 'unsigned int[]'}
And similar warnings. Correct these by updating the prototype. Remove
the prototype for ddr3_tip_read_pup_value as it is unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDkSkAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyD24B/9t87hFqWovJvVAcoUT
JoTqFblplE4Sckssy0cQyR7sRpzuZEaakUeAxaLFecBN6Tn30YJEG3hNpEDCLEbA
hn/oiZ4hQ3JA9Yu2SHepQi0fLqdAjkQtMXy57o3Mk20GBLtPtpdItUHxg3iyeMSj
Ny1mm/KjL6ltmNeGfYfeqRf435Rm718DB94wCZTgS9woYe3Z5YRDNBPyL7u27hpY
2WiyvvU9EA12mjGYdEt5sCqnTQZFtHHlEWNHz4a3db6HkcPV7pfr+SpTNJjcFhIg
O7VN7yUTwnV0UGu5IXTWcZqFIqJkLPbPX5cvkSBnnaGge4e0K3Cw36Nv/EqCY8LX
gWfu
=Ru8k
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.10 cycle:
This small fixes set is dedicated to fixing the onewire subsystem for
the at91 boards which was broken since 2020.04.
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
At the moment, the U-Boot serial_msm driver does not initialize the
UART_DM_DMEN register with the required value. Usually this does not
cause any problems, because there is Qualcomm's LK bootloader running
before U-Boot which initializes the register with the correct value.
It's important that this register is initialized correctly, because
the U-Boot driver does not make use of the BAM/DMA or single character
mode functionality of the UART controller. A different bootloader
before U-Boot might initialize the register differently.
For example, on DragonBoard 410c U-Boot can also be installed to the
"aboot" partition (replacing LK entirely). In this case U-Boot is
loaded directly by SBL, which seems to use the single-character mode
for some reason. In single character mode there is always just one
char in the FIFO, instead of the 4 characters expected by
msm_serial_fetch(). It also causes issues with "earlycon" later in
the Linux kernel, which tries to output 4 chars at once,
but only the first char will be written.
This causes early UART log in Linux to be corrupted like this:
[ 00ano:ameoi .Q1B[ 00ac _idaM00080oo'ahani-lcle._20). 15NdNii 5 SPMSJ20:U2
[ 00rkoolmsamel
[ 00Fw ]elamletopsioble
[ 00ore
instead of
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd030]
[ 0.000000] Machine model: Qualcomm Technologies, Inc. APQ 8016 SBC
[ 0.000000] earlycon: msm_serial_dm0 at MMIO 0x00000000078b0000 (options '')
[ 0.000000] printk: bootconsole [msm_serial_dm0] enabled
Make sure to initialize UART_DM_DMEN correctly to fix this issue
when loading U-Boot directly after SBL (instead of through LK).
There is no functional difference when loading U-Boot through LK
since LK also initializes UART_DM_DMEN to 0x0. [1]
[1]: https://git.linaro.org/landing-teams/working/qualcomm/lk.git/tree/platform/msm_shared/uart_dm.c?h=dragonboard410c-LA.BR.1.2.7-03810-8x16.0-linaro3#n203
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Convert the CONFIG_SYS_I2C_LPC32XX configuration symbol from an include
directive to a Kconfig value.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the of_match/compatible string to the lpc32xx i2c driver so it works
correctly with device-tree.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
The lpc32xx driver was not obtaining the per-device base address correctly
from the device tree. Fix the FIXME in order to get the correct base address.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
This is a driver for the HSSPI SPI controller on SynQuacer SoC.
The HSSPI has command sequence mode (memory mapped) and
direct mode (FIFO access). The driver will operate it under
the direct mode. And before booting OS, it switch back to the
command sequence mode since that is compatible with default
EDK2 behavior.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add ECAM based SynQuacer PCIe RC driver. This driver configures the
PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device
is configured by firmware (EDK2), it doesn't re-configure in the kernel.
So as same as EDK2, U-Boot needs to configure it before boot the kernel.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Without this fix, scsi-scan will cause a synchronous abort
when accessing ops->scan.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a limited pulse-width modulator to sandbox's Chromium OS
Embedded Controller emulation. The emulated PWM device supports multiple
channels but can only set a duty cycle for each, as the actual EC
doesn't expose any functionality or information other than that. Though
the EC supports specifying the PWM channel by its type (e.g. display
backlight, keyboard backlight), this is not implemented in the emulation
as nothing in U-Boot uses this type specification.
This emulated PWM device is then used to test the Chromium OS PWM driver
in sandbox. Adding the required device node to the sandbox test
device-tree unfortunately makes it the first PWM device, so this also
touches some other tests to make sure they still use the sandbox PWM.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Each _device_ belonging to a given uclass of course has its own ->ops,
of a type determined by and known to the uclass.
However, no instance of a uclass_driver seems to populate ->ops, and
the only reference to it in code is this relocation.
Moreover, it's not really clear what could sensibly be assigned; it
would have to be some "struct uclass_ops *" providing a set of methods
for the core to call on that particular uclass, but should the need
for that ever arise, it would be better to have a member of that
particular type instead of void*.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio_request_by_name should be called with proper flags.
The 0 value flag is invalid, and causes bad initialization of the gpio.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This commit adds support to piton_mmc driver for OpenPiton-riscv64
This driver has many things set as preconfigured because the hardware
automatically configures most of the settings during startup.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Replace 'pciaux' with 'pcieaux', including name string and function
prefix. The old name string, 'pciaux', might cause an error if PCIe
driver is changed to use clk_get_by_name() with 'pcieaux' to get
clock.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove the define EQOS_DESCRIPTOR_ALIGN unused since the
commit 6f1e668d96 ("net: dwc_eth_qos: Pad descriptors to cacheline size")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure that errors in the PHY driver .startup() method, such as no
link, are propagated and not ignored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The RGMII spec supports optional in-band status reporting for the speed
and duplex negotiated on the copper side, and the ENETC driver enables
this feature by default.
However, this does not work when the PHY does not implement the in-band
reporting, or when there is a MAC-to-MAC connection described using a
fixed-link. In that case, it would be better to disable the feature in
the ENETC MAC and always force the speed and duplex to the values that
were negotiated and retrieved over MDIO once the autoneg is finished.
Since this works always, we just do it unconditionally and drop the
in-band code.
Note that because we need to wait for the autoneg to complete, we need
to move enetc_setup_mac_iface() after phy_startup() returns, and then
pass the phydev pointer all the way to enetc_init_rgmii().
The same considerations have led to a similar Linux driver patch as well:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c76a97218dcbb2cb7cec1404ace43ef96c87d874
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Given that even a fixed-link has an associated phy_device, there is no
reason to operate in a mode when dm_eth_phy_connect fails.
Remove the driver checks for a NULL priv->phy and just return -ENODEV
when that happens.
Copyright updated according to corporate requirements.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SMC911x Ethernet MACs can be integrated using a 16 or 32-bit bus.
The driver needs to know about this choice, which is the reason for us
having a Kconfig symbol for that.
Now this bus width is already described using a devicetree property, and
since the driver is DM compliant and is using the DT now, we should query
this at runtime. We leave the Kconfig choice around, in case the DT is
missing this property.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SMC911x Ethernet driver needs to know which accessor functions it
can use to access the MMIO registers. For that reason we have a Kconfig
choice between 16 and 32-bit bus width.
Since it's only those two options that we (and the Linux kernel)
support, and there does not seem to be any evidence of another bus
width anywhere, limit the Kconfig construct to a simple symbol.
This simplifies the code and allows a later rework to be much easier.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
