Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Reset ENET_RST_B to make ENET function stable.
Since DM_GPIO enabled, we use "gpio_spi@0_5" which corresponds
to ENET_RST_B.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.
This is V2 of this patch with changes recommended by the maintainer
CC: Jagan Teki <jteki@openedev.com>
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need
to do a read-modify-write operation.
Simplify the code by writing directly to this register.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
mx7dsabresd has two targets:
- mx7dsabresd_defconfig: boots in non-secure mode
- mx7dsabresd_secure_defconfig: boots in secure mode
Print the mode that is being used to help users to easily identify
which target is running on the board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect
D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3
is actually 1.2V.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
When running the 'ums' command we get:
=> ums 0 mmc 0
UMS: disk start sector: 0x0, count: 0xe18000
g_dnl_register: failed!, error: -22
ERROR: g_dnl_register failed
at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage()
Fix this by initializing USB OTG1 port as USB device mode instead of host.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Support qspi flashes for mx7dsabresd
1. introduce pin mux settings
2. enable qspi clock
3. introduce related macro definitions
Default QSPI is not enabled, since we need hardware rework to use QSPI,
see SPF-28590, page 9:
"
QSPI signals are muxed with EPDC_D[7:0]
When using QSPI: de-populate R388-R391, R396-R399
populate R392-R395, R299, R300
"
After hardware rework, define CONFIG_FSL_QSPI in mx7dsabresd.h. qspi
flashes can be deteced and read/erase/write. Log info:
"
=> sf probe
SF: Detected MX25L51235F with page size 256 Bytes, erase size 64 KiB, total 64 MiB
=> sf read 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Read: OK
=> sf erase 0 0x4000000
SF: 67108864 bytes @ 0x0 Erased: OK
=> sf write 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Written: OK
"
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
We use outer pmic reset and drop internal reset signal, bmode will
not work as expected, so drop boot mode code for 7dsabresd board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Adrian Alonso <aalonso@freescale.com>
get_board_rev() is not actually providing the board revision.
It just returns the CPU revision instead.
As the CPU revision is already printed on boot, there is no
reason to have get_board_rev(), so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Include <usb/ehci-fsl.h> in order to fix the following sparse warning:
board/freescale/mx7dsabresd/mx7dsabresd.c:538:5: warning: symbol 'board_ehci_hcd_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We use trigger pmic reset to reset the board, so set bit SRS to
disable internal WDOG_RESET_B_DEB to make reset stable.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
