Commit graph

8 commits

Author SHA1 Message Date
Peng Fan
1e4ed2d69d imx8mp-evk: switch to use binman
Use binman to pack images

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:53 +02:00
Clement Faure
56d2050f40 imx8m: Add DEK blob encapsulation for imx8m
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.

To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y

Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:52 +02:00
Ye Li
f19d1a946c arm: dts: imx8mp-evk: Add FEC PHY reset timing
Add phy-reset-duration and phy-reset-post-delay to FEC node for PHY
reset, otherwise the PHY does not work correctly.

Signed-off-by: Ye Li <ye.li@nxp.com>
2021-03-01 10:21:36 +01:00
Peng Fan
48b90f86c5 imx: imx8mp_evk: enable eth support
Add board code to configure the network interface
Add net defconfig

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Andrey Zhizhikin
50b1a69cee ARM: dts: imx8m: add UHS or HS400/HS400ES properties
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.

Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
2020-12-26 12:36:35 +01:00
Andrey Zhizhikin
247bbeb74c ARM: dts: imx8m: increase off-on delay on the SD Vcc regulator
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.

Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.

Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-12-26 12:36:19 +01:00
Marek Vasut
f24dea4e1b ARM: imx8m: Fix reset in SPL on NXP iMX8MP EVK
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-05-01 13:46:22 +02:00
Peng Fan
439321b264 imx: add i.MX8MP EVK board
Add basic i.MX8MP EVK board support

U-Boot SPL 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)
power_pca9450b_init
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Failed to find clock node. Check device tree
WDT:   Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0

U-Boot 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)

CPU:   Freescale i.MX8MP rev1.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MPlus EVK board
DRAM:  6 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
u-boot=> mmc list
FSL_SDHC: 1 (SD)
FSL_SDHC: 2

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-08 13:20:09 +01:00