Commit graph

2032 commits

Author SHA1 Message Date
Janine Hagemann
be71a74c59 net: phy: ti: Recover from "port mirroring" N/A MODE4
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.

To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).

To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.

Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"

https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954

Based on commit ac6e058b75be ("net: phy: dp83867: Recover from "port mirroring"
N/A MODE4") of mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2018-10-10 12:28:54 -05:00
Janine Hagemann
fba725f410 net: phy: ti: Add lane swapping support in the DP83867 TI's PHY driver
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.

One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).

Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:28:53 -05:00
Bin Meng
dda5251037 net.h: Include linux/if_ether.h to avoid duplication
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:28:52 -05:00
Bin Meng
339613eba5 net: pch_gbe: Make probe/remove static
These two routines are internal to pch_gbe driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-09 14:18:21 -05:00
Bin Meng
b06d76f9ae linux/compat.h: Add netdev_### log macros
Currently there are two ethernet drivers (mvneta.c and mvpp2.c) that
has netdev_### (eg: netdev_dbg) log macros defined in its own driver
file. This adds these log macros in a common place linux/compat.h.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-09 14:18:17 -05:00
Janine Hagemann
3d1bd5b590 net: gmac_rockchip: Add handling for RGMII_ID/RXID/TXID
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.

Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.

Based on commit eaf70ad14cbb ("net: stmmac: dwmac-rk: Add
handling for RGMII_ID/RXID/TXID") for mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-04 21:15:46 +02:00
Janine Hagemann
04acabd22c net: gmac_rockchip: Fix a register write in rk3328_gmac_set_to_rgmii
We have to use RK3328_RXCLK_DLY_ENA_GMAC_ENABLE instead of
RK3328_RXCLK_DLY_ENA_GMAC_MASK in rk3328_gmac_set_to_rgmii()
to enable the RX delay.
The MASK was used in a wrong way.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Reviewed-by: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-04 21:15:46 +02:00
Tom Rini
27f622d568 Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
 Switch to driver model for SATA on LS1021A and LS1043A.
 Add support for LS1012AFRWY rev C board.
 Enable SMMU for LS1043A.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJbrkHRAAoJEO1FWZTaC520r3UQAIBntTglI1QK7YizVxZ1x9DL
 42oSEIwkuN0wbndR7Jzx4EPPFJ8yX4v3stoxC3qS5DQ9kHMzuqRQcIDYbcn5Qy7Z
 vd0mBUmpkRjr988pSaSHVQ8kPasncb545fCUumrXrCmhuG5Ea2Itw1zLdsTf7X5n
 39KxFUOAR63BDCT0ZlR4VyMo01GxxHWCzRQH/rOWVzOcJsWF7R52hWIBBzVDxKPv
 HF9SYaAB0PTFgSjJx5wYQ4xPdHVUp+svtYSJE8JYzEr/BvOVtL2iEi4t2rk19CrX
 IaVMFydlv2iDgWdoSZFCCN/6lGDWSv1LWPDglWhLQhOYvrJOjZfgzzeAGU7wqoz4
 JVjSLf6dHeOma55dbP/epDmyDFqWIfNOQ3uP4RM57xJ0PXQuT7ACVJctr6kHVTGL
 1ZZxPdKSSf9lvtzoogPTTYRD5Ry7ud3sYZ0v3OHN1sbVcaHaVoHPeXeSz1sLg3Q+
 zhUo1lXx4FcTz9R1fafdcqqAk/YGMZ7sBE+uYJPgExnApxrZID9IiOdGIBxo8jiK
 ozLmaCIDqRyu/qhQW9WMri1tvYdKwq/739gBvvcIcrLR5RzfNUdwWjhtBokPQQnS
 WZNqd3/0N8ZFGz7V0GOxCDnAo4nwQeZVFGMtTpoCtjPvr6DWBHsEUlQHTT3dQKz/
 TXygMYUYGA+/vux0Dt4I
 =XRFI
 -----END PGP SIGNATURE-----

Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq

Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
2018-09-29 11:47:32 -04:00
Zhao Qiang
db947fa038 net: fman: Support both new and legacy FMan Compatibles
Recently the FMan Port and MAC compatibles were changed. This patch
aligns the FMan Port and MAC compatibles to the new FMan device tree
binding document. The FMan device tree binding document can be found
in the Linux kernel version 3.18.0, commit
297d35fd2a7d3fbd4e5c0f0c1c18213117ba11ba
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt

This patch doesn't affect legacy compatibles support.

Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 10:01:27 -07:00
Pramod Kumar
7abf92327f ls1012a: remove debug info from u-boot log
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:58:42 -07:00
Prabhakar Kushwaha
87519a9ece driver: net: fsl-mc: Memset MC reserve ram memory before usage
Memory reserved for Management Complex needs to be cleaned before any
usage.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:55:21 -07:00
Nipun Gupta
a78df40cba u-boot: fixup the iommu-map property of fsl-mc node
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.

Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:55:05 -07:00
Yinbo Zhu
c3ced8a6ed ppa/fm/qe: use block layer in ppa/fm/qe driver
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:48:51 -07:00
Tom Rini
bbef20d479 Xilinx changes for v2018.11
- Handle BOARD_LATE_INIT via Kconfig
 
 SPL:
 - Enable GZIP for all partitions types(not only for kernel)
 
 ZynqMP:
 - Rearrange pmufw version handling
 - Support newer PMUFW with improved fpga load sequence
 
 Zynq:
 - Cleanup config file
 - Simplify zybo config by enabling option via Kconfig
 
 net:
 - Fix gems max-speed property reading
 - Enable support for fixed-link phys
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAluss3IACgkQykllyylKDCFQWwCfc7bvoUN1vevGYTfcG2cEYSF5
 IxQAoI/10FGWJS6rgTG0IVFvoSI1ALhA
 =Q/Tg
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11

- Handle BOARD_LATE_INIT via Kconfig

SPL:
- Enable GZIP for all partitions types(not only for kernel)

ZynqMP:
- Rearrange pmufw version handling
- Support newer PMUFW with improved fpga load sequence

Zynq:
- Cleanup config file
- Simplify zybo config by enabling option via Kconfig

net:
- Fix gems max-speed property reading
- Enable support for fixed-link phys
2018-09-27 08:29:10 -04:00
Michal Simek
3888c8d197 net: zynq_gem: Add support for fixed-link phy
Based on dt-specs fixed-link doesn't require phy-handle to be used.
Fix driver to only read phy related setting when phy-handle is found.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-09-27 07:59:26 +02:00
Siva Durga Prasad Paladugu
f213dbbdec net: zynq_gem: Fix reading of max-speed property
max-speed property is part of phynode and it has to be
read using ofnode_read_u32_default(). This fixes the issue
of incorrect max-speed read from DT.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-26 10:15:00 +02:00
Sekhar Nori
e2597be5bc drivers: net: cpsw: add support to update phy address
On some boards using TI CPSW, it may be possible that
PHY address was not latched correctly, and the actual
address that the phy responds on is different from that
set in device-tree. For example, see this problem report
on beaglebone black:

https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J

Add support to check for this condition and use the
detected phy address when its safe to do so.

Also, add a public API that exposes the phy address of
a given slave. This can be used to update device-tree that
is passed to Linux kernel.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-25 21:49:18 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
719afeb0b3 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2018-08-17 07:24:34 -04:00
Marek Vasut
215a06565a net: designware: socfpga: Add Arria10 extras
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-08-13 22:35:42 +02:00
Pankaj Bansal
c022ec039d fsl/mc: Limit the ethernet name to ETH_NAME_LEN
The ethernet name should be within the ETH_NAME_LEN, as this
is the buffer space allocated to ethernet name.

Otherwise, this causes buffer overflow.

Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-08 08:23:49 -07:00
Siva Durga Prasad Paladugu
26026e695a net: zynq_gem: convert to use livetree
This patch updates the zynq gem driver to support livetree.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:23 -05:00
Grygorii Strashko
41080e180c drivers: net: zynq_gem: fix phy dt node setting
Now zynq_gem driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
2018-07-26 14:08:23 -05:00
Grygorii Strashko
d4bb981700 drivers: net: cpsw: fix phy dt node setting
Now CPSW driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:23 -05:00
Grygorii Strashko
aadbd97843 net: phy: xilinx: switch to use phy_get_ofnode()
Use PHY API phy_get_ofnode() helper to get PHY DT node.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:22 -05:00
Grygorii Strashko
b8d7ec782f net: phy: dp83867: switch to use phy_get_ofnode()
Use PHY API phy_get_ofnode() helper to get PHY DT node.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
2018-07-26 14:08:22 -05:00
Grygorii Strashko
eef0b8a930 net: phy: add ofnode node to struct phy_device
Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):

- network drivers
	priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
				   priv->interface);
	<-- phydev is connected to dev which is UCLASS_ETH device

	if (priv->phy_of_handle > 0)
		dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
	<-- phydev->dev->node is overwritten by phy-handle DT node

- PHY driver in .config() callback
	int node = dev_of_offset(dev);
	<-- PHY driver uses overwritten dev->node
        const void *fdt = gd->fdt_blob;

	 if (fdtdec_get_bool(fdt, node, "property"))
		...

As result, UCLASS_ETH device can't be used any more for DT accessing.

This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:22 -05:00
Joe Hershberger
05b60ac549 net: phy: Clean up includes of common.h
We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.

Also, common.h includes config.h as the first thing it does, so don't
include it directly.

Series-to: u-boot
Series-cc: Grygorii Strashko <grygorii.strashko@ti.com>
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.

[1] https://patchwork.ozlabs.org/cover/940104/
END
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:22 -05:00
Grygorii Strashko
3ab75cf76e net: phy: dp83867: switch to use ofnode api
Switch to use more generic ofnode API instead of FDT API.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
2018-07-26 14:08:21 -05:00
Murali Karicheri
63d3192984 net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).

It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.

Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
2018-07-26 14:08:21 -05:00
Chris Packham
fb73107698 net: mvgbe: convert to DM
Add driver model support to the mvgbe driver. As a temporary measure
both DM and non-DM uses are supported. Once all the users have been
converted the non-DM support can be dropped.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:21 -05:00
Chris Packham
e9bf75c9d3 net: mvgbe: prepare for conversion to driver model
Extract some function bodies to helper functions that can be reused in
the DM/non-DM implementations.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-26 14:08:20 -05:00
Joe Hershberger
f40a31e695 sandbox: eth-raw: Add a SIMPLE_BUS to enumerate host interfaces
Ask the OS for each of its interfaces and for each one, bind a U-Boot
device and then probe it. This will allocate the priv data structure
that is then populated.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:19 -05:00
Joe Hershberger
b96ced9cdb sandbox: eth-raw: Make random MAC addresses available to eth-raw
We don't necessarily know how many MAC addresses we'll need, so implement
a ROM read so we always have something valid.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:18 -05:00
Joe Hershberger
c9e2caff85 sandbox: eth-raw: Allow interface to be specified by index
With systemd stable interface names, eth0 will almost never exist.
Instead of using that name in the sandbox.dts, use an index.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:18 -05:00
Joe Hershberger
ac13270b49 sandbox: eth-raw: Add a function to ask the host about localhost
Instead of doing a simple string compare against "lo", look for the flag
that indicates a localhost interface.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:18 -05:00
Joe Hershberger
8c7988b6db net: sandbox-raw: Convert raw eth driver to livetree
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:18 -05:00
Joe Hershberger
b32dd183c2 net: sandbox: Convert sandbox mock eth driver to livetree
Use the dev_ functions to access DT properties.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:18 -05:00
Joe Hershberger
c25f40627f net: Correct comment in Kconfig
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:18 -05:00
Michael Trimarchi
efd0b79106 eth: dm: fec: Add gpio phy reset binding
Add the missing gpio phy reset binding to the gpio and
reset time configuration

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-23 10:28:01 +02:00
Lothar Felten
e46d73fa96 net: sun8i-emac: support R40 GMAC
Add support for the GMAC found in the Allwinner R40/V40 SoC.

The R40 GMAC interface is not controlled by the syscon register but
has a separate configuration register in the CCU.
The clock gate and reset bits are in a different register compared
to the other SoCs supported by this driver.
The driver uses the -gmac suffix for the R40 because the R40 also
has a different 100 MBit MAC (EMAC).

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2018-07-16 12:27:27 +05:30
Lothar Felten
c6a21d6615 net: sun8i-emac: set mux and clock by driver data
Use driver data->variant information to select device specific
pin mux and phy clock settings.

Suggested by Jagan Teki

Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
2018-07-16 12:27:27 +05:30
Lothar Felten
2f15743633 net: sun8i-emac: fix printing NULL character
If the variant is not set and therefore NULL, do not attempt to print
the variant.

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2018-07-16 12:27:27 +05:30
Ley Foon Tan
495c70f9df net: designware: Add reset ctrl to driver
Add code to reset all reset signals as in Ethernet DT node. A reset
property is an optional feature, so only print out a warning and do not
fail if a reset property is not present.

If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-09 15:28:28 -04:00
Rabeeh Khoury
318b5d76b6 net: mvneta: zero Tx descriptors on init
Make the initialization sequence consistent with the Linux kernel
driver.

Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-02 14:14:20 -05:00
Rabeeh Khoury
0f8888b763 net: mvneta: dcache flush TX descriptors at init
This fixes sporadic timeout on initial packet Tx (usually ARP), with an
error message like:

  timeout: packet not sent

Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-02 14:14:20 -05:00
Michal Simek
d1b226b7d4 net: zynq_gem: Initialize val variable in zynq_gem_miiphy_read()
phyread can timeout and val will contain random value. Initialize it to
zero not to report random value in case of error.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-02 14:14:19 -05:00
Marek Vasut
159b329226 net: sh_eth: Support reset GPIO both in mac and phy node
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-06-19 06:15:55 +02:00
Marek Vasut
701db6e9c6 net: ravb: Support reset GPIO both in mac and phy node
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-06-19 06:15:55 +02:00
Marek Vasut
536fb5d47c net: ravb: Filter out supported PHY features
The RAVB only supports 100Full and 1000Full operation, it does not support
10Full or any Half-duplex modes. The PHY could still advertise those features
though, so filter out the PHY features accordingly.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-06-19 06:15:55 +02:00
Marek Vasut
c4a8d9ca04 net: ravb: Do not shut down clock in start callback
Do not stop the clock in the start callback in case of failure, keep
them running to also keep the PHY running. The failure could be ie.
PHY failing to negotiate link and if the clock get shut down, another
attempt at bringing the link up would fail. The clock right now are
started in probe function and stopped in remove function, which is
the correct behavior.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-06-19 06:15:55 +02:00
Michal Simek
5b2c9a6ce3 net: gem: Check return value from memalign/malloc
Functions can return NULL in case of error that's why checking return
value is needed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:59:04 -05:00
Michal Simek
7674b64d78 net: zynq_gem: Initialize phyreg variable
In case of phyread()/phy_setup_op() timeout code is working with
uninitialized phyreg variable. Initialize this variable to make sure
that code it not working with random value.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:18 -05:00
Michal Simek
b33d4a5fc7 net: zynq_gem: Fix return type for phy...()
wait_for_bit_le32 returns negative value on failure. Fix phy...() to
handle these failures properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Chris Packham
5194ed7edc net: mvgbe: extract common code for SMI wait
Combine repeated code from smi_reg_read/smi_reg_write into a common
function smi_wait_ready.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Quentin Schulz
c61221948c net: designware: set the PS bit when resetting DMA bus in MII configuration
On the SPEAr600 SoC, which has the dwmac1000 variant of the IP block,
the DMA reset never succeeds when a MII PHY is used (no problem with a
GMII PHY). The designware_eth_init() function sets the
DMAMAC_SRST bit in the DMA_BUS_MODE register, and then
polls until this bit clears. When a MII PHY is used, with the current
driver, this bit never clears and the driver therefore doesn't work.

The reason is that the PS bit of the GMAC_CONTROL register should be
correctly configured for the DMA reset to work. When the PS bit is 0,
it tells the MAC we have a GMII PHY, when the PS bit is 1, it tells
the MAC we have a MII PHY.

Doing a DMA reset clears all registers, so the PS bit is cleared as
well. This makes the DMA reset work fine with a GMII PHY. However,
with MII PHY, the PS bit should be set.

We have identified this issue thanks to two SPEAr600 platform:

- One equipped with a GMII PHY, with which the existing driver was
working fine.

- One equipped with a MII PHY, where the current driver fails because
the DMA reset times out.

Note: Taken from https://www.spinics.net/lists/netdev/msg432578.html

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Chris Packham
3cb51dad0d net: phy: mv88e61xx: Force CPU port link up
When connecting to from a CPU direct to a 88e6097 typically RGMII is
used. In order for traffic to actually pass we need to force the link up
so the CPU MAC on the other end will see the link.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Jon Nettleton
199b27bb70 mvebu: neta: align DMA buffers
This makes sure the DMA buffers are properly aligned for the
hardware.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Kunihiko Hayashi
a8927795ef net: add Socionext AVE ethernet driver support
Add driver for Socionext AVE ethernet controller that includes MAC and
MDIO bus supporting RGMII/RMII modes.
The driver behaves the ethernet driver model (DM_ETH) with devicetree.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Radu Bulie
98017a1fb5 drivers/net/vsc9953: Initialize action RAM in VCAP complex
VCAP tables must be initialized even if no advanced classification
is used. If no initialization is performed, then ECC error will
be observed by the user when the first packet enters the l2switch.
The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM
multi-bit ECC error.
This patch fixes the aforementioned ECC error by performing the
initialization of VCAP tables.

Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:16 -05:00
Alex Kiernan
286bea2e85 net: cpsw: ti: Reap completed packets before stopping interface
If you send a final packet just before stopping the interface (e.g. a final
ACK as part of the UDP fastboot protocol), then that packet isn't reliably
delivered onto the wire.

Reap packets prior to stopping the interface to ensure any which are
in-flight make it out. Also remove buffer and len from the call to
cpdma_process() as we weren't using them on their return.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:16 -05:00
Vicentiu Galanopulo
552e7c57d0 net/phy/cortina: Add support for CS4223 PHY
Add support for Cortina CS4223 10G PHY
  - As per the CS4223 specs, an EEPROM module is
    connected to the PHY. At startup the PHY reads
    the firmware line and tries to load the firmware
    into the internal memory.
  - This driver reads the EEPROM status
    and checks if firmware has been loaded

Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:15 -05:00
Joe Hershberger
6e35686d89 net: sunxi: Correct MAC address register order
Put the enetaddr data in the same order as it was before the change in
commit ace1520cb5 ("net: sunxi-emac: Write HW address via function")

Reported-by: Udo Maslo <u.maslo@web.de>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:15 -05:00
Mario Six
5e9d9abe08 tsec: Fix reading phy registers from DT
Bus translations should be applied when reading the address of the sgmii
phy registers from the DT. Use ofnode_get_addr_index instead of the
plain ofnode_read_u32_default to fix this.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:15 -05:00
Vinitha V Pillai
2d91b53331 LS1012AFRWY: Add Secure Boot support
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support

Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11 12:34:45 -07:00
Tom Rini
040b2583c3 Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-06-02 16:58:27 -04:00
Marek Vasut
34f1dba983 net: ravb: Add R8A77990 E3 compatible
Add new compatible to the Ethernet AVB driver for R8A77990 E3 SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-01 09:47:02 +02:00
Rick Chen
28b52a6fb7 net: ftmac100: Fix compiler warning
Fix warnings as below when compile in 64-bit.

warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
2018-05-29 14:45:03 +08:00
Tuomas Tynkkynen
ed9072c797 net: Drop CONFIG_TSI108_ETH
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-05-23 17:30:03 -04:00
Chris Packham
f6e62ee04c net: MVGBE don't automatically select PHYLIB
When Kconfig support was added for MVGBE it included automatically
selected PHYLIB support. But MVGBE does not need PHYLIB it will build
fine without it. Commit ed52ea507f ("net: add Kconfig for MVGBE")
should have been a no-op in terms of build size but because of the
selecting PHYLIB the openrd configs increased in size.

Remove the automatic selection of PHYLIB, boards that need it will have
already enabled it in their config header file.

Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17 17:38:31 +02:00
Chris Packham
ed52ea507f net: add Kconfig for MVGBE
Add Kconfig for MVGBE and update boards to select this.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-14 21:28:38 -04:00
Chris Packham
edcf7eacbd net: mvgbe: remove CONFIG_DOVE
Nothing defines CONFIG_DOVE so remove the code that uses it.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14 21:28:38 -04:00
Marek Behún
cf2cf8510a net: mvneta: Fix fault when wrong device tree
The driver does not check id phy_connect failed (for example on wrong
property name in device tree). In such a case a fault occurs and the
CPU is restarted.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Tom Rini
c590e62d3b Merge git://git.denx.de/u-boot-fsl-qoriq 2018-05-11 07:09:21 -04:00
Tom Rini
f739fcd831 SPDX: Convert a few files that were missed before
As part of the main conversion a few files were missed.  These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict.  This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.

Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-10 20:38:35 -04:00
Yogesh Gaur
a6f2a6eafe driver: net: fsl-mc: updated copyright info
Updated copyright info for the issues reported after running
check-legal test.

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
b25f8e2112 Merge git://git.denx.de/u-boot-imx 2018-04-30 07:14:05 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Lukasz Majewski
948239ea16 dts: dm: fec: imx53: Provide proper compatible string for imx53 fec driver
After this change the DM FEC ETH driver can be also reused on some imx53
devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-04-26 09:28:49 +02:00
Lukasz Majewski
178d4f0099 eth: dm: fec: Change FEC PHY mask setting from CONFIG_PHYLIB to CONFIG_FEC_MXC_PHYADDR
Without this commit we do have an explicit dependency on CONFIG_PHYLIB
when one wants to set PHY ADDR on a iMX board (FEC + driver model).

This shall be changed to CONFIG_FEC_MXC_PHYADDR, as only when we do have
it set, we shall mask out other devices.

As a side effect, when CONFIG_FEC_MXC_PHYADDR is not set, we scan PHY bus
for connected PHY devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-04-26 09:27:22 +02:00
Joe Hershberger
16879cd25a net: phy: Don't limit phy addresses by default
Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-04-13 15:56:47 -05:00
Marek Vasut
b107fd5bab net: sh_eth: Add remaining Gen2 DT compatible
Add compatible strings for R8A7790, R8A7793 and R8A7794, since the
contemporary DTs use those don't have a generic match value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:52 -05:00
Siva Durga Prasad Paladugu
69065e8ff4 net: zynq_gem: Use max-speed property from dt
Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:48 -05:00
Ye Li
2087eac257 net: fec: Fix issue in DM probe timeout
Since the probe function has changed to reset FEC controller prior than
setup PHY. If reset FEC controller timeout, the priv->phydev is not
initialized, so can't free it.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:39 -05:00
Peng Fan
979e0fc862 net: fex_mxc: add i.MX6UL/SX/SL compatible
Add i.MX6UL/SX/SL compatible.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:39 -05:00
Peng Fan
fbada4855d net: fec: sharing MDIO for two enet controllers
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.

To i.MX28, adapt to use the new config

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-13 15:47:38 -05:00
Peng Fan
8b20386356 net: fec: set dev->seq to priv->dev_id
To platforms has two enet interface, using dev->seq could
avoid conflict.

i.MX6UL/ULL evk board net get the wrong MAC address from fuse,
eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the
priv->dev_id to device->seq as the real net interface alias id then
.fec_get_hwaddr() read the related MAC address from fuse.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:38 -05:00
Peng Fan
1bcabd7921 net: fec_mxc: simplify fec_get_miibus
No need to provide two prototype for this function.
Use ulong for the first parameter, then this function
could be shared for DM/non DM case.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:37 -05:00
Ye Li
07763ac928 net: fec_mxc: Fix DM driver issue in recv
When using ethernet DM driver, the recv interface has a
change with non-DM interface, that driver needs to set
the packet pointer and provide it to upper layer to process.

In fec driver, the fecmxc_recv functions does not handle the
packet pointer parameter. This may cause crash in upper layer
processing because the packet pointer is not set.

This patch allocates a buffer for the packet pointer and free it
through free_pkt interface.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:37 -05:00
Matt Pelland
0a85f024c5 net: mvneta: support setting hardware address
mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.

Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:31 -05:00
Tom Rini
2600df4f8e Xilinx changes for v2018.05-rc2
- Various DT changes and sync with mainline kernel
 - Various defconfig updates
 - Add SPL init for zcu102 revA
 - Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
   and zc1751-dc3
 - Net fixes - xlnx,phy-type
 - 64bit axi ethernet support
 - arasan: Fix nand write issue
 - fpga fixes
 - Maintainer file updates
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAlrLeoUACgkQykllyylKDCEilwCgmdalBG7zVd9oekK142ILPdRf
 OgsAn2oWw69JhU3i4mv039lNgYpIzlRb
 =shae
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.05-rc2

- Various DT changes and sync with mainline kernel
- Various defconfig updates
- Add SPL init for zcu102 revA
- Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
  and zc1751-dc3
- Net fixes - xlnx,phy-type
- 64bit axi ethernet support
- arasan: Fix nand write issue
- fpga fixes
- Maintainer file updates
2018-04-09 11:06:21 -04:00
Siva Durga Prasad Paladugu
c643c491b9 net: phy: xilinx_phy: Read phytype using property xlnx,phy-type
This patch reads phytype from property "xlnx,phy-type" instead
od simply looking for "phy-type". This is to be inline with
Linux and also fixes the issue of detecting it wrongly in
u-boot.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09 12:14:51 +02:00
Vipul Kumar
047f3bf828 axi: ethernet: Added support for 64 bit addressing for axi-ethernet
This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09 12:14:50 +02:00
Alex Kiernan
9925f1dbc3 net: Move enetaddr env access code to env config instead of net config
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

  board/ti/am335x/built-in.o: In function `board_late_init':
  board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
  u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-08 23:00:58 -04:00
Alex Kiernan
f02b8d1761 Migrate CONFIG_DRIVER_TI_CPSW to Kconfig
This converts CONFIG_DRIVER_TI_CPSW to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-08 23:00:58 -04:00
Mario Six
171510522e treewide: Migrate CONFIG_TSEC_ENET to Kconfig
Migrate the CONFIG_TSEC_ENET option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 15:12:53 -04:00
Christophe Leroy
18f8d4c60d powercp: mpc8xx: move commproc.h
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06 16:30:37 -04:00
Christophe Leroy
ee1e600c13 powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xx
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06 16:30:37 -04:00