priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast priv->iobase with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds ethernet driver for MediaTek MT7620 SoC.
The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).
The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.
This driver supports MT7530 giga switch connects to port 5.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Take into account all RGMII interface types. Depending on it
the RGMII PHY's timings are setup.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk_set_rate() returns the set rate in case of success and a
negative number in case of failure. Consider failure only the
negative numbers.
Fixes: 3ef64444de ("dm: net: macb: Implement link speed change callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Different implementation of USER IO register needs different
mapping for bit fields of this register. Add implementation
for this and, since clken is part of USER IO and it needs to
be activated based on per SoC capabilities, add caps in
macb_config where clken specific information needs to be filled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words
after the descriptor. Use this to pad the descriptors to cacheline size and
remove the need for noncached memory altogether. Moreover, this lets Tegra
use the generic cache flush / invalidate operations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
A sporadic condition occurs when the "bad packet" error is triggered
repeatedly, which results in "bad packet" messages scrolling on the
console during transfer. To avoid triggering this, reset the internal
RXFC count on the first occurance of the "bad packet", which forces
the code to re-read the RX packet count from the MAC, and prevents
any additional "bad packet" messages if there are no more packets in
the MAC. Also print better debug information if this condition occurs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Implement programming MAC address to the hardware also for device model
configuration.
Fixes: b565b18a29 ("board: ge: bx50v3: Enable DM for PCI and ethernet")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Read phy address from device tree and use it to find the phy device
if not found then search in the range of 0 to 31.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Enable 32-bit or 64-bit DMA in the macb driver based on the macb
hardware compatibility and it is configured with structure macb_config
in the driver.
The Microchip PolarFire SoC Memory Protection Unit(MPU) gives the 64-bit
DMA access with the GEM, the MPU transactions on the AXI bus is 64-bit
not 32-bit So 64-bit DMA is enabled for the Microchip PolarFire SoC GEM.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add a return value to bb_miiphy_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services
provided by ATF to setup the PHY interface.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Checking for seq == -1 is effectively checking that the device is
activated. The new sequence numbers are never -1 for a bound device, so
update the check.
Also drop the note about valid sequence numbers so it is accurate with the
new approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Several Octeon drivers operate by setting the sequence number of their
device. This should not be needed with the new sequence number setup. Also
it is not permitted. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not necessary anymore, since device_bind_ofnode() does
the same thing and works with both flattree and livetree.
Rename it to indicate that it is special.
Signed-off-by: Simon Glass <sjg@chromium.org>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case there is an EEPROM attached to the KS8851 MAC and the EEPROM
contains a valid MAC address, the MAC address is loaded into the NIC
registers on power on. Read the MAC address out of the NIC registers
and provide it to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
As per hardware documentation, ECx_PMUX has precedence
over SerDes protocol.
For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII
through SerDes protocol but ECx_PMUX configured them as RGMII,
then the ports will be configured as RGMII and not SGMII.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
