According to "Table 5-1. Boot Device Select" (page 335,
i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017)
the BOOT_CFG1[3] have following values (regarding EIM booting):
0 - NOR flash and 1 - ONENAND
This commit provides correct identification of the boot medium for IMX6Q
boards booting from NOR memory (MCCMON6 is one of them).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Not all i.MX6 pads use the same drive strength table. So far only the
240 Ohm to 34 Ohm table was available. Because the constants used have
speaking names it can be confusing to use e.g. PAD_CTL_DSE_48ohm when
according to the reference manual 52 Ohm is the correct value. This
patch adds the 260 Ohm to 37 Ohm table.
For example, the IOMUXC_SW_PAD_CTL_PAD_SD2_CLK register (SD-card clock)
uses the added table.
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Working with HAB on the i.MX7 we've encountered a case where a board that
successfully authenticates u-boot when booting Linux via OPTEE subsequently
fails to properly bring up the RTC.
The RTC registers live in the low-power block of the Secure Non-Volatile
Storage (SNVS) block.
The root cause of the error has been traced to the HAB handing off the
SNVS-RTC in a state where HPCOMR::NPSWA_EN = 0 in other words where the
Non-Privileged Software Access Enable bit is zero. In ordinary
circumstances this is OK since we typically do not run in TZ mode, however
when we boot via HAB and enablng TrustZone, it is required to set
HPCOMR::NPSWA_EN = 1 in order for the upstream Linux driver to have
sufficient permissions to manipulate the SNVS-LP block.
On our reference board it is the difference between Linux doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000021 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000000 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x80002100 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
30370000.snvs:snvs-rtc-lp as rtc0
snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to2018-04-01 00:51:04 UTC (1522543864)
and doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000020 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000001 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x00002020 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: failed to enable rtc -110
snvs_rtc: probe of 30370000.snvs:snvs-rtc-lp failed with error -110
hctosys: unable to open rtc device (rtc0)
Note bit 1 of LPCR is not set in the second case and is set in the first
case and that bit 31 of HPCOMR is set in the second case but not in the
first.
Setting NPSWA_EN in HPCOMR allows us to boot through enabling TrustZone
and continue onto the kernel. The kernel then has the necessary permissions
to set LPCR::SRTC_ENV (RTC enable in the LP command register) whereas in
contrast - in the failing case the non-privileged kernel cannot do so.
This patch adds a simple init_snvs() call which sets the permission-bit
called from soc.c for the i.MX7. It may be possible, safe and desirable to
perform this on other i.MX processors but for now this is only tested on
i.MX7 as working.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
commit ed286bc80e ("imx: hab: Check if CSF is valid before authenticating
image") makes use of "__packed" as a prefix to the "struct hab_hdr"
declaration.
With my compiler "gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)" we
get:
./arch/arm/include/asm/mach-imx/hab.h:42:25: error: expected ‘=’, ‘,’, ‘;’,
‘asm’ or ‘__attribute__’ before ‘{’ token
struct __packed hab_hdr {
Fix this problem by including <linux/compiler.h>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We should take the MX6DP and MX6QP options in consideration
in the I2C_PADS_INFO macro.
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We should take the MX6DP and MX6QP options in consideration
when defining imx_iomux_v3_setup_pad().
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Include i.MX8M in lcdif register layout map.
Also included i.MX7ULP in this patch, since share same with i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add SiP (Silicon Provider) services function to issue
SMC call to Arm Trusted Firmware.
More SiP information could be found in
https://github.com/ARM-software/arm-trusted-firmware/blob/master/
docs/arm-sip-service.rst
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The hab_rvt_failsafe() callback according to the HABv4 documentation:
"This function provides a safe path when image authentication has failed
and all possible boot paths have been exhausted. It is intended for use by
post-ROM boot stage components, via the ROM Vector Table."
Once invoked the part will drop down to its BootROM USB recovery mode.
Should it be the case that the part is in secure boot mode - only an
appropriately signed binary will be accepted by the ROM and subsequently
executed.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It will be helpful to boot commands to know if the HAB is enabled. Export
imx_hab_is_enabled() now to facilitate further work with this data-point in
a secure-boot context.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tidy up the HAB namespace a bit by prefixing external functions with
imx_hab. All external facing functions past this point will be prefixed in
the same way to make the fact we are doing IMX HAB activities clear from
reading the code. authenticate_image() could mean anything
imx_hab_authenticate_image() is on the other hand very explicit.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The hab_rvt_check_target() callback according to the HABv4 documentation:
"This function reports whether or not a given target region is allowed for
either peripheral configuration or image loading in memory. It is intended
for use by post-ROM boot stage components, via the ROM Vector Table, in
order to avoid configuring security-sensitive peripherals, or loading
images over sensitive memory regions or outside recognized memory devices
in the address map."
It is a useful function to support as a precursor to calling into
authenticate_image() to validate the target memory region is good.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The various i.MX BootROMs containing the High Assurance Boot (HAB) block
rely on a data structure called the Image Vector Table (IVT) to describe to
the BootROM where to locate various data-structures used by HAB during
authentication.
This patch adds a definition of the IVT header for use in later patches,
where we will break the current incorrect dependence on fixed offsets in
favour of an IVT described parsing of incoming binaries.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
u-boot command "hab_auth_img" tells a user that it takes
- addr - image hex address
- offset - hex offset of IVT in the image
but in fact the callback hab_auth_img makes to authenticate_image treats
the second 'offset' parameter as an image length.
Furthermore existing code requires the IVT header to be appended to the end
of the image which is not actually a requirement of HABv4.
This patch fixes this situation by
1: Adding a new parameter to hab_auth_img
- addr : image hex address
- length : total length of the image
- offset : offset of IVT from addr
2: Updates the existing call into authenticate_image() in
arch/arm/mach-imx/spl.c:jump_to_image_no_args() to pass
addr, length and IVT offset respectively.
This allows then hab_auth_img to actually operate the way it was specified
in the help text and should still allow existing code to work.
It has the added advantage that the IVT header doesn't have to be appended
to an image given to HAB - it can be prepended for example.
Note prepending the IVT is what u-boot will do when making an IVT for the
BootROM. It should be possible for u-boot properly authenticate images
made by mkimage via HAB.
This patch is the first step in making that happen subsequent patches will
focus on removing hard-coded offsets to the IVT, which again is not
mandated to live at the end of a .imx image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
CSF_PAD_SIZE should be defined in hab.h, move it to that location now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The size of the IVT header should be defined in hab.h move it there now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Both usages of authenticate_image treat the result code as a simple binary.
The command line usage of authenticate_image directly returns the result
code of authenticate_image as a success/failure code.
Right now when calling hab_auth_img and test the result code in a shell a
passing hab_auth_img will appear to the shell as a fail.
The first step in fixing this behaviour is to fix-up the result code return
by authenticate_image() itself, subsequent patches fix the interpretation
of authenticate_image so that zero will return CMD_RET_SUCCESS and non-zero
will return CMD_RET_FAILURE.
The first step is fixing the return type in authenticate_image() so do that
now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.
This fixes a boot regression.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:266:5: warning:
no previous prototype for ‘board_mmc_get_env_dev’
[-Wmissing-prototypes] int board_mmc_get_env_dev(int devno)
Remove this warning by adding the function prototype into sys_proto.h file.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add the reserved boot mode used in the bmode command for i.MX 6UL
and 6ULL as introduced in commit 3fd9579085 ("imx: mx6ull: fix USB
bmode for i.MX 6UL and 6ULL").
Also replace BMODE_UART with BMODE_RESERVED, which is more appropriate.
Commit 96aac843b6 ("imx: Use IMX6_BMODE_* macros instead of numericals")
added macros for boot modes, in the process the reserved boot mode got
named BMODE_UART. We use the reserved boot mode in the bmode command to
let the boot ROM enter serial downloader recovery mode. But this is only
a side effect, the actual boot mode is reserved...
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
