This method in the sound API is optional since some drivers can do this
when probing or as part of SoC init. Mark it as such.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the PCH has 4 operations and these are reasonably widely used
in the drivers. But sometimes we want to add rarely used operations, and
each of these currently adds to the size of the PCH operations table.
Add an ioctl() method which can be easily expanded without any more impact
on the operations table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass currently has no tests. Add a sandbox driver and some simple
tests to provide basic coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: Use "sandbox,pch" for the compatible string, for consistency]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present this uclass is selected only on x86. In order to add a test for
it, it must also support sandbox. Create a new CONFIG_PCH option and
enable it on x86 and sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not used outside this file so make it static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this driver does not check whether it is able to actually
communicate with the I2C controller. It prints a timeout message but still
considers the probe to be successful.
To fix this, add some checking that the init succeeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present it is not possible to use the syscon devices for PCI devices
since a regmap is required. Since PCI uses a 3-cell address the conversion
of the 'reg' property to an address always fails. In any case, the regmap
is not useful with PCI since devices are accessed through the PCI bus
which regmap does not support.
Add a special case for PCI syscon devices, so that they don't set up a
regmap.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Before the patch scsi would report the same device number for all SCSI
devices, e.g.
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 0: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
With the patch the same device number is reported as is used in
scsi_read():
Device 0: (1:0) Vendor: ATA Prod.: Crucial_CT128M55 Rev: MU01
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Device 1: (1:0) Vendor: ATA Prod.: Rev:
Type: Hard Disk
Capacity: not available
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fsl_ddr_board_options is generally defined in board
board's ddr.c, but some boards like lx2160ardb board
does not need this function.
Defining fsl_ddr_board_options as weak function to
resolve compilation errors for such boards.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[PK: Fix checkpatch warnings]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch prevent the Stratix 10 FPGA driver incorrectly return the
transaction ID as the mailbox error code. It should always return the
actual mailbox error code from SDM firmware.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Poll for iDMAC TX/RX interrupt before disable DMA.
This to prevent disable DMA before data is transfer
completed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The DT2FF register must be configured differently for HS400 mode
and for HS200/SDR104 mode. Configure the DT2FF register according
to the recommended datasheet settings for each mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set the HOST_MODE register WMODE bit according to the SDHI bus width,
that is 0 for 64bit bus and 1 for 16/32bit bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch adds support to load 24bpp BMP files on 16bpp displays. This
will be used by the theadorable board. The "old" bmp command did support
this operartion mode and to not break compatibility with the move to
DM_VIDEO, we need to add this support to the "new" bmp code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
There are HDMI displays where hpd pin is not connected, thus
we cannot get it to work unless we specifically set the resolution.
Rework the display probing, so hotplug detect failure causes
fallback to probing ddc for EDID data.
Signed-off-by: Priit Laes <priit.laes@paf.com>
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbca ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
mxs_nand_init_dma is only referenced from mxs_nand.c. It's not
referenced in any headers or outside code, so this patch
defines it as static.
Signed-off-by: Adam Ford <aford173@gmail.com>
The LogicPD board uses a Micron Flash with ECC. To boot this from
SPL, the ECC needs to be correctly configured or the BCH engine
times out.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add native tsc calibration function. Calibrate the tsc timer the same
way as linux does in arch/x86/kernel/tsc.c.
Fixes booting for Apollo Lake processors.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The dm_gpio_set_value() routine sets signal logical level, with
GPIO_ACTIVE_LOW/HIGH value taken into account. Reset active value is 1
(asserted), while reset inactive value is 0 (de-asserted). Fix the reset
toggle code to set the correct reset logic value.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For !DM case busses are listed as
ZynqMP> i2c bus
Bus 0: zynq_0
Bus 1: zynq_0->PCA9544A@0x75:0
Bus 2: zynq_0->PCA9544A@0x75:1
Bus 3: zynq_0->PCA9544A@0x75:2
Bus 4: zynq_1
Bus 5: zynq_1->PCA9548@0x74:0
Bus 6: zynq_1->PCA9548@0x74:1
Bus 7: zynq_1->PCA9548@0x74:2
Bus 8: zynq_1->PCA9548@0x74:3
Bus 9: zynq_1->PCA9548@0x74:4
Bus 10: zynq_1->PCA9548@0x75:0
Bus 11: zynq_1->PCA9548@0x75:1
Bus 12: zynq_1->PCA9548@0x75:2
Bus 13: zynq_1->PCA9548@0x75:3
Bus 14: zynq_1->PCA9548@0x75:4
Bus 15: zynq_1->PCA9548@0x75:5
Bus 16: zynq_1->PCA9548@0x75:6
Bus 17: zynq_1->PCA9548@0x75:7
where is exactly describing i2c bus topology.
By moving to DM case i2c mux buses are using names from DT and because
i2c-muxes describing sub busses with the same names like i2c@0, etc it
is hard to identify which bus is where.
Linux is adding topology information to i2c-mux busses to identify them
better.
This patch is doing the same and composing bus name with topology
information.
When patch is applied with topology information on zcu102-revA.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@ff020000->i2c-mux@75->i2c@0
Bus 3: i2c@ff020000->i2c-mux@75->i2c@1
Bus 4: i2c@ff020000->i2c-mux@75->i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@ff030000->i2c-mux@74->i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@ff030000->i2c-mux@74->i2c@1
Bus 7: i2c@ff030000->i2c-mux@74->i2c@2
Bus 8: i2c@ff030000->i2c-mux@74->i2c@3
Bus 9: i2c@ff030000->i2c-mux@74->i2c@4
Bus 10: i2c@ff030000->i2c-mux@75->i2c@0
Bus 11: i2c@ff030000->i2c-mux@75->i2c@1
Bus 12: i2c@ff030000->i2c-mux@75->i2c@2
Bus 13: i2c@ff030000->i2c-mux@75->i2c@3
Bus 14: i2c@ff030000->i2c-mux@75->i2c@4
Bus 15: i2c@ff030000->i2c-mux@75->i2c@5
Bus 16: i2c@ff030000->i2c-mux@75->i2c@6
Bus 17: i2c@ff030000->i2c-mux@75->i2c@7
Behavior before the patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
For i2c controllers which are missing alias in DT there is no req_seq
setup. This function is setting up proper ID based on highest found
alias ID.
On zcu102 this is the behavior when patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Before this patch applied (controllers have -1 ID)
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0 (active 0)
54: eeprom@54, offset len 1, flags 0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@5
Bus -1: i2c@6
Bus -1: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is a need to find out the first free i2c ID which can be used for
i2s buses (including i2c buses connected to i2c mux). Do it early in
init and share this variable with other i2c classes for uniq bus
identification.
add from hs:
fix build problem in i2c-uclass.c for omap devices
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
At present there is still some samsung-specific code in the audio codecs.
Remove it so that these can be used by other SoCs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow misc devices to have children, so that we can use this uclass for
cases where a child device (e.g. I2S) needs to access a misc driver for
transferring data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while enabling io regulators. This way the driver doesn't see an error
when disabling an always-on regulator and when enabling is not supported.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
regulator_set_enable() api throws an error in the following three cases:
- when requested to disable an always-on regulator
- when set_enable() ops not provided by regulator driver
- when enabling is actually failed.(Error returned by the regulator driver)
Sometimes consumer drivers doesn't want to track the first two scenarios
and just need to worry about the case where enabling is actually failed.
But it is also a good practice to have an error value returned in the
first two cases.
So introduce an api regulator_set_enable_if_allowed() which ignores the
first two error cases and returns an error as given by regulator driver.
Consumer drivers can use this api need not worry about the first two
error conditions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit e17e0ceb83.
It is advised to return an error when trying to disable an always-on
regulator and let the consumer driver handle the error if needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
While uclass_find_device() fails with -ENODEV in case of list_empty
strangely uclass_find_first_device() returns 0.
Fix uclass_find_first_device() to also fail with -ENODEV instead.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
References:
[1] http://www.ti.com/lit/pdf/sprz426
[2] http://www.ti.com/lit/pdf/SPRACA9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
To activate the csg option, the driver need to set the bit2
of PLLNCR register = SSCG_CTRL: Spread Spectrum Clock Generator
of PLLn enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of clk dump command and
display information during probe (under CONFIG_DISPLAY_CPUINFO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Because stgen is initialized with HSI clock, we need to
recalculate the counter when changing frequency.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove support of ck_usbo_48m clock node in device tree,
but force 48MHz frequency to prepare alignment
with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The DM_FLAG_PRE_RELOC shall be enabled in SBSA PL011 uart driver
as this driver is used in NXP based SoCs
It is necessary to have Serial console running before relocation
The !CONFIG_IS_ENABLED(OF_CONTROL) [*] check is set as "workaround"
for DM problem : 4687919684
This flag is set if board does not support device-tree and using
platform data, In DM Model either of device tree or platform data
can be used to fetch device configuration
It is possible to use SBSA UART with CONFIG_DM_SERIAL but witout
corresponding device tree description (OF_CONTROL)
Other board/SoCs have this flag set unconditionally
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
This driver is used on several big endian mips board.
So we could use raw I/O function instead of forcing
big endian access.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When using CMD6 to switch eMMC card timing from HS200/HS400 to HS/legacy,
do not poll for the completion status using CMD13, but rather wait 50mS.
Once the card receives the CMD6 and starts executing it, the bus is in
undefined state until both the card finishes executing the command and
until the controller switches the bus to matching timing configuration.
During this time, it is not possible to transport any commands or data
across the bus, which includes the CMD13.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The internal DMAC asserts DMA transfer end bit too early on older
version of the TMIO IPs which use bit 17 for DTRAEND. Add 1uS
delay after the completion of DMA transfer and before invalidating
the cache to let the DMAC fully complete the transfer. Otherwise,
it could happen that the last few bytes of a transferred data are
not available.
A test case to trigger this behavior is the following command, ran
on the U-Boot command line, with Sandisk 16 GiB UHS-I card inserted
into SDHI slot 0 and with first partition being of type FAT:
=> while true ; do mmc rescan ; fstype mmc 0:1 ; done
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Different versions of the SDHI core use either bit 17 or bit 20 for the
DTRAEND indication, which can differ even between SoC revisions. Make
the DTRAEND bit position part of the driver private data, so that the
probe function can set this accordingly. Set this to 20 on Socionext
SoCs and either 17 or 20 on Renesas SoCs, depending on the SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
It is wrapper for calling of_alias_get_highest_id() when live tree is
enabled and fdtdec_get_alias_highest_id() if not.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same functionality was added to Linux for i2c bus registration with this
commit message:
"
of: base: add function to get highest id of an alias stem
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"
Add it also to U-Boot for DM I2C support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
spi_flash and spi_flash_ids are no longer needed after SPI NOR
migration. Remove them.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible
SPI Flash device nodes. Therefore make U-Boot also to look for the same
compatible string so that we can use Linux DTS files as is.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync changes from Linux SPI NOR framework to add 4 byte addressing
support. This is required in order to support flashes like MT35x
that no longer support legacy Bank Address Register(BAR) way of accessing
>16MB region.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Many SPI controllers have special MMIO interfaces which provide
accelerated read/write access but require knowledge of flash parameters
to make use of it. Recent spi-mem layer provides a way to support such
controllers.
Therefore, add spi-mem support to spi-nor-core as a way to support SPI
controllers with MMIO interface. SPI MEM layer takes care of translating
spi_mem_ops to spi_xfer()s in case of legacy SPI controllers.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add non DM version of SPI_MEM to support easy migration to new SPI NOR
framework. This can be removed once DM_SPI conversion is complete.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
It is necessary to call spi_claim_bus() before starting any SPI
transactions and this restriction would also apply when calling spi-mem
operations. Therefore claim and release bus before requesting transfer
via exec_op.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Extend spi_mem_adjust_op_size() to take spi->max_write_size and
spi->max_read_size into account.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
SPI controllers support all types of SPI modes including dual/quad bus
widths. Therefore remove constraint wrt SPI mode from spi-mem layer.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
- Move Armada XP / 38x PCIe driver to DM_PCI from me
- Move Armada XP / 38x LCD driver to DM_VIDEO from me
- Add uDPU board (Armada-3720) from Vladimir
[trini: Fix warning in pci-uclass.c by removing ret from
pci_uclass_child_post_bind as it no longer calls functions with
a return code to catch.]
Signed-off-by: Tom Rini <trini@konsulko.com>II
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this
move, the legacy interface board_video_init() is removed from the
theadorable board code (only user of this video driver). The support
via DT will be added in a separate patch.
This patch also enables DM_VIDEO for the theadorable board, as this is
needed to not break git bisect'ability.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.
To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This function will be used by the Marvell Armada XP/38x PCIe driver,
which is moved to DM right now. So let's extract the functionality
from pci_uclass_child_post_bind() to make it available.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
The OMAP36 and DM37 TRM state to disable extneded drain IO before
changing the PBIAS. This patch does this before pmic writes if
the CONFIG_MMC_OMAP36XX_PINS flag is set and the cpu family is
omap36xx
Signed-off-by: Adam Ford <aford173@gmail.com>
After the merge of the new, generic pinctrl-code, the include for
rockchip/Kconfig was missing. Add it here, so we can select the
pinctrl-driver for SPL.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To make adding new subdirectories easier, let's enforce alphabetical
ordering of the includes of Kconfig files in the respective
subdirectories.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Allow rockchip boards to use GPIOs before driver model is ready. This is
really only useful for setting GPIOs to enable the early debug console, if
needed on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
These clocks are needed to get MMC running. We don't actually support
setting them yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It is helpful to print the clock number as well as the index, so that this
can be looked up in the binding file. Update the debug() statement to do
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we used the pinctrl-rockchip driver, these code is not needed,
so remove them.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use this driver to fit all Rockchip SOCs and to support
the desired pinctrl configuration via DTS.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a sound driver for rk3288 supporting chromebook_jerry. This uses the
I2S driver, and existing audio codec and the clock/pinmux support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a driver for I2S which allows audio data to be sent from the SoC to
the audio codec. The sample rate and other settings are hard-coded for now
as there is no suitable device-tree binding available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for setting pinctrl and clock for I2S on rk3288. This allows
the sound driver to operate. These settings were created by rkmux.py
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If the host does not respond in time, the initialization fails. However
the usb ether driver will still be registered. This will make
usb_gadget_probe_driver() fail the next time the initialization is
attempted because it cannot find an available UDC.
Fixing this by calling _usb_eth_halt() when the init fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This functions can be reused by other MSCC SoCs therefore,
make them more generic and move them in separate files.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This adds video output support for Amlogic GXBB/GXL/GXM chips.
The supported ports are CVBS and HDMI (based on DW_HDMI).
When using HDMI, only DMT modes are supported.
There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB)
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed defines alignment in meson_canvas.c]
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Some IPs like the meson VPU can only feed a particular pixel format to
dw_hdmi. As of now, the driver is hardcoded to use RGB888 as input.
This commit enables different pixel format inputs, with the appropriate
CSC configuration.
Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Some IPs like the meson VPU have a specific way to write to dw_hdmi
registers. Make it configurable.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
[added commit description]
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
MESON_GX_VPU_POWER_DOMAIN should depend on POWER_DOMAIN.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This unbreaks dfu mmc_file_op which is currently broken since using the
load cmd on a buffer from heap is not allowed - added with
commit aa3c609e2b ("fs: prevent overwriting reserved memory")
Fixes: commit aa3c609e2b ("fs: prevent overwriting reserved memory")
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Some Allwinner clock devices have parent clocks and reset gates itself,
which need to be activated for them to work.
Add some code to just assert all resets and enable all clocks given.
This should enable the A80 MMC config clock, which requires both to be
activated. The full CCU devices typically don't require resets, and have
just fixed clocks as their parents. Since we treat both as optional and
enabling fixed clocks is a NOP, this works for all cases, without the need
to differentiate between those clock types.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
If a board DT describes a cd-gpios property, but also marks the storage
as non-removable, we must ignore the GPIO (as Linux does).
Teach the DM_MMC part of the Allwinner MMC driver about the
non-removable DT property, to fix DM_MMC access on the SoPine and
Pine64-LTS board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Now that we have the gate clocks and the reset gates in our new
Allwinner clock driver, let's make use of them in the MMC driver, when
DM_MMC is defined.
We treat the reset device as optional now, as the older SoCs don't
implement it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A80 gates clock already be part of CLK framework, so just
add mod_clk offset with A80 compatible string.
Cc: Rask Ingemann Lambertsen <rask@formelder.dk>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Unlike other Allwinner SoC's, H6 uses a different MMC mod clock offset.
Connect that with the respective compatible string.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add MMC compatible strings for A83T, A64, H5.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The A80 handles resets and clock gates for the MMC devices differently,
outside of the CCU IP block. Consequently we have a separate clock
device with a separate binding for that.
Implement that with the respective clock gates and resets to allow the
A80 taking part in the DM_MMC game.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: fix a80 mmc clock config compatible]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add the MMC clock gates and reset bits for all the Allwinner SoCs.
This allows them to be used by the MMC driver.
We don't advertise the mod clock yet, as this is still handled by the
MMC driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: add V3S, A80 gates/resets]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Adding pinconf support is necessary to enable boot from SPI
without breaking the eMMC. When booting from SPI, the ROM code
leave pull downs on the eMMC pad.
We need to set pinconf provided in DT to solve this
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added missing comma in pinctrl-meson-axg-pmx.c]
The ihs_video_out driver's error handling is incorrect in two places
(one is a missing negation, and in one place a error should be ignored).
Fix these two instances.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Current EDID detailed timing parser errors out when either
horizontal or vertical pulse sync width is 0, thus not
allowing a display with EDID listed below work properly.
EDID below works ok within Linux although it warns about
these two fields being 0. Therefore relax the checks a bit
so we can actually use this the screen out of the box.
Of-course, this display itself is somewhat quirky display with
following anti-features:
- HPD pin is not usable
- although resolution is 640x480, only top 240 pixels are visible
$ xxd -p display.edid
00ffffffffffff0005a1e00301000000150f0103800f05780a0f6ea05748
9a2610474f200000010101010101010101010101010101012a08804520e0
0b1020004000953600000018000000fd0034441a2403000a202020202020
0000001000310a20202020202020202020200000001000002a4030701300
782d1100001e006b
$ edid-decode display.edid
EDID version: 1.3
Manufacturer: AMA Model 3e0 Serial Number 1
Digital display
Maximum image size: 15 cm x 5 cm
Gamma: 2.20
RGB color display
First detailed timing is preferred timing
Display x,y Chromaticity:
Red: 0.6250, 0.3398
Green: 0.2841, 0.6044
Blue: 0.1494, 0.0644
White: 0.2802, 0.3105
Established timings supported:
640x480@60Hz 4:3 HorFreq: 31469 Hz Clock: 25.175 MHz
Standard timings supported:
Detailed mode: Clock 20.900 MHz, 149 mm x 54 mm
640 672 672 709 hborder 0
480 484 484 491 vborder 0
-hsync -vsync
VertFreq: 60 Hz, HorFreq: 29478 Hz
Monitor ranges (GTF): 52-68Hz V, 26-36kHz H, max dotclock 30MHz
Dummy block
Dummy block
Checksum: 0x6b (valid)
Signed-off-by: Priit Laes <priit.laes@paf.com>
Signed-off-by: Priit Laes <plaes@plaes.org>
The initialization function calls a nand_chip.scan_bbt(mtd) but
scan_bbt is never initialized resulting in an undefined function
pointer. This will direct the function pointer to nand_default_bbt
defined in the same file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
When building mxc_spi driver on ARM64 platforms, get below build warnings.
Fix it in this patch.
In file included from include/common.h:48:0,
from drivers/spi/mxc_spi.c:9:
drivers/spi/mxc_spi.c: In function ‘spi_xchg_single’:
drivers/spi/mxc_spi.c:232:21: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
_func_, bitlen, (u32)dout, (u32)din);
^
include/log.h:135:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/spi/mxc_spi.c:231:2: note: in expansion of macro ‘debug’
debug("%s: bitlen %d dout 0x%x din 0x%x\n",
^~~~~
drivers/spi/mxc_spi.c:232:32: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
_func_, bitlen, (u32)dout, (u32)din);
^
include/log.h:135:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/spi/mxc_spi.c:231:2: note: in expansion of macro ‘debug’
debug("%s: bitlen %d dout 0x%x din 0x%x\n",
^~~~~
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The pinctrl supports to set any bit in input register on iMX6 if
the MSB of input value is 0xff. But the driver uses signed int for
input value, so when executing the codes below, it won't meet.
Because this is arithmetic right shift.
if (input_val >> 24 == 0xff)
Fix the issue by changing the input_val, config_val and mux_mode to u32.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently if we have more than one phy on the MDIO bus, we do not have a
good mechanism for determining which should be used at runtime. Enable the
FEC driver to determine the address for the PHY from the device tree.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Linux kernel binding is using atmel,24c08 compatible string. On the
other hand there is atmel,24c08a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
These eeproms are available on several ZynqMP development boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Do this by using $(SPL_) in Makefiles and CONFIG_IS_ENABLED in C code.
This ensures the files and features are only built into the right build
for which they are enabled. Using the macros to simplify this patch was
made possible by the config symbol rename done in the last patch.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
It is not possible to link the SPL image when CONFIG_GPIO is enabled
but CONFIG_SPL_GPIO is not. Use the IS_ENABLED macro instead to
correctly check whether CONFIG_{SPL_}GPIO is enabled.
This commit fixes the following errors:
* undefined reference to `dm_gpio_get_value
* undefined reference to `gpio_request_by_name'
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[trini: Move guard to fix warning in msdc_ops_get_wp()]
Signed-off-by: Tom Rini <trini@konsulko.com>
The code is checking for incomplete read when it see the INT_XFER_COMPL
flag, but it forget to first check whether there is anything left in the
FIFO to copy to the RX buffer. This means that sometimes we will get
errors because of erroneous incomplete read operation.
This commit fixes the driver re-ordering the code so that we first
check for data inside the RX fifo and only after check the status
of the INT_XFER_COMPL flag.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
A couple of trivial fixes and improvements for ARC
Most notable are:
* Move of ENV_SIZE/ENV_OFFSET to Kconfig
* Fix with private structure allocation for arc_uart
* Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
Apparently we never allocated buffer for arc_serial_platdata
which for some reason never caused problems when executed in nSIM.
But in Qemu this causes expected problems.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Print information about Aquantia system interface and firmware loaded
on the phy.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If System Interface protocol is USXGMII then enable USXGMII autoneg
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ether_crc was added to the core net code in commit 53a5c424bf
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to the datasheet to access the extended registers we have to:
1. Write Register 31 Data = 0x0XYZ (Page 0xXYZ)
2. Read/Write the target Register Data
3. Write Register 31 Data = 0x0000 or 0xa42 (switch back to IEEE
Standard Registers)
Hook the missing functions so that we can use the `mdio rx/wx` command to
easily access the extended registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
