When rtl_recv() of rtl8169 is called, OWNbit of status register
is not enable occasionally.
rtl_recv() doesn't work normally when the driver doesn't do
appropriate processing.
This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The taihu board used gpio_read_out_bit which reads the output register and not
the pin state.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
1. Make the CSB bus pipeline depth as 4, and enable
the repeat mode;
2. Raise the eTSEC emergency priority;
3. Use the highest IP blocks clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The latter version stops when "run load" fails for whatever reasons
rendering the combination *a lot* more secure.
Signed-off-by: Detlev Zundel <dzu@denx.de>
This patch fixes a problem seen on PPC4xx boards, when no MAC address is
defined. Then no ethernet interface is available but a simple "tftp"
command will return without any error message which is quite confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch fixes a problem seen on PPC4xx boards, when no MAC address is
defined. Then no ethernet interface is available but a simple "tftp"
command will return without any error message which is quite confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 5013c09f (Makefile: cleanup "clean" target) introduced a
problem for out-of-tree builds which caused "make clean" to fail.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.
There were differences in the PHY setup between Linux and U-Boot.
This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>
Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>
If I try to "cp.b <ram> <dataflash>", u-boot selects normal flash
routines instead of dataflash. This is because it checks "if source
address is not dataflash" instead of target address.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
This fixes the cluster size tests in the FAT32 file system.
The current implementation of VFAT support doesn't work if the
referred cluster has an offset > 16bit representation, causing
"fatload" and "fatls" commands etc. to fail.
Signed-off-by: michael trimarchi <trimarchi@gandalf.sssup.it>
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix alignment fault on ARM when running modules. With out an explicit
linker file gcc4.2.1 will half word align __bss_start's value. The word
dereference will crash hello_world.
signed-off-by Richard Woodruff <r-woodruff2@ti.com>
erratum 5.6 states the autoneg completion bit is functional only if the
autoneg bit is asserted.
This fixes any secondarily-issued networking commands on non-gigabit
links on the mpc8360 mds board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
