There is a delay function that was commented out. This patch
re-enables it, because it will be needed for da850 ohci support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Update device tree for luton to add support for luton pcb90.
This pcb has 24 ports from which 12 ports are connected to
SerDes6G.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Update Luton network driver to have support also for pcb90. The pcb90
has 24 ports from which 12 ports are connected to SerDes6G.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Microsemi SoC defines CONFIG_SYS_SDRAM_BASE to be 0x80000000, which
represents the start of kseg0 and represents a virtual address. Meaning
that the initrd_start and initrd_end point somewhere kseg0.
When these parameters are passed to linux kernel through DT
they are pointing somewhere in kseg0 which is a virtual address but linux
kernel expects the addresses to be physical addresses(in kuseg) because
it is converting the physical address to a virtual one.
Therefore update the uboot to pass the physical address of initrd_start
and initrd_end by converting them using the function virt_to_phys before
setting up the DT.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove "select MSCC_BITBANG_SPI_GPIO" since Kbuild option was deleted
back in commit ace9c103df:
commit ace9c103df
Author: Lars Povlsen <lars.povlsen@microchip.com>
Date: Tue Jan 8 10:38:35 2019 +0100
mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
Add ethernet nodes for Serval SoCs family. There are 2 pcb in this
family: pcb105 and pcb106.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Add network driver for Microsemi Ethernet switch.
It is present on Serval SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
In case the ddr training was failing, it couldn't reset, it was just
hanging. Therefore reimplement it, so when ddr training is failing
it would call _machine_restart, which power downs the DDR and does
a force reset.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths
of DMA. ADMA2 uses a table of descriptors for aggregating DMA requests.
This significantly improves read and write throughput.
Add Support for the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
In preparation for addition of ADMA2 support, cleanup SDMA handling by
moving it to a new sdhci_prepare_dma() function. Also add a flags field
in sdhci_host to indicate if DMA is enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The wp-gpios property is used for gpio, if this is set, the WP pin is muxed
to gpio function, can't be used as internal WP checking. However the codes
remain to use internal WP checking.
This patch changes to examine the "fsl,wp-controller" for enabling internal WP
checking, and "wp-gpios" for muxing to gpio.
Signed-off-by: Ye Li <ye.li@nxp.com>
When sd/mmc work at DDR mode, like HS400/HS400ES/DDR52/DDR50 mode,
the output clock rate is half of the internal clock rate.
This patch set the DDR_EN bit first for DDR mode, hardware divide
the usdhc clock automatically, then follow the original sdr clock
setting method.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
The btrfs implementation methods .ls(), .size() and .read() returns 1 on
failure, but the command handlers expect values <0 on failure.
For example if given a nonexistent path, the load command currently
returns success, and hush scripting does not work.
Fix this by setting return values of these methods to -1 instead of 1 on
failure.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
When CROSS_BUILD_TOOLS is set, set HOSTCFLAGS to CFLAGS otherwise CC
will be used with HOSTCFLAGS which seems wrong
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f2 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
The DM* family of SOCs is no longer supported. We now support the
omap-l138 lcdk board and Lego EV3 platform. Reflect those changes
in the README.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Add am335x-pocketbeagle to CONFIG_OF_LIST in am335x_evm_defconfig.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
TI-SCI firmware will only respond to messages when the
TI_SCI_FLAG_REQ_ACK_ON_PROCESSED flag is set. Most messages
already do this, set this for the ones that do not.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Alejandro Hernandez <ajhernandez@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in U-Boot")
introduced Kconfig option for gzip in U-Boot, but help text
says gzip for SPL, which is wrong. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The existing comments where confusing read and write. The comment for
fs_write() had:
"@addr: The address to read into"
So let's rework the comments and format them in Sphinx style.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
In commit ad6054f1fe where support for the
Sancloud BeagleBone Enhanced (BBE) was added, new conditional
configuration of either MII pin muxing or RGMII pin muxing is done
depending on the board type. However, the old call to set up MII pin
muxing was not removed.
This may result in misconfiguration of the pin muxing for the BBE or
duplicate configuration for other boards and so we remove this obsolete
call.
Signed-off-by: Paul Barker <paul.barker@sancloud.co.uk>
Restart operation never exists and reset operation never
makes the watchdog expire immediately but expire_now operation
does.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Upcoming sysfw (2019.03) will not open the channelized firewalls during
init, it only going to do so in response to the channel configuration
message.
Remove the channel state checks done before the channel configuration and
move it after the configuration for warning purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
An earlier commit converted the TISCI receive timeouts to be specified
in ms rather than us however it failed to take this change into account
when passing the actual timeout to be used when invoking the mailbox
receive API. This leads to the actual timeout to be 1,000 times shorter
than expected and as a result certain TISCI operations would fail.
Fix the issue by converting the timeout declared in ms to us on the fly
as expected by the respective API.
Fixes: fd6b40b1ba ("firmware: ti_sci: Add support for NAVSS resource management")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the mmc maintainer from Jaehoon to me.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
Currently packet data is wrongly extracted when metadata is NULL.
Fix it and negate the if check.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
-----BEGIN PGP SIGNATURE-----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=GUpA
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc2
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
Some SPI controllers can't write nor->page_size bytes in a single step
because their TX FIFO is too small, but when that happens we should
make sure a WRITE_EN command before each write access and READ_SR command
after each write access is issued.
We should allow nor->write() to return a size that is smaller than the
requested write size to gracefully handle this case.
Also, the spi_nor_write_data() should return the actual number of bytes
that were written during the spi_mem_exec_op() operation.
This patch is a combination of two commits backported from kernel:
commit 630d6bd8a3b4 ("mtd: spi-nor: Support controllers with limit ...")
commit 3baa8ec88c2f ("mtd: devices: m25p80: Make sure WRITE_EN is ...")
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> # microzed
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
This options will be enabled by default by CZ.NIC shipped U-Boot. Enable
them in defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the gpio command and driver for the I2C connected
pca9538 controller, to be able to determine if SFP module is present in
the Turris Omnia router.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The twsi_wait function reads the control register for interrupt flag,
and if interrupt flag is present, it immediately reads status register.
On our device this sometimes causes bad value being read from status
register, as if the value was not yet updated.
My theory is that the controller does approximately this:
1. sets interrupt flag in control register,
2. sets the value of status register,
3. causes an interrupt
In U-Boot we do not use interrupts, so I think that it is possible that
sometimes the status register in the twsi_wait function is read between
points 1 and 2.
The bug does not appear if I add a small delay before reading status
register.
Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).
The idea behind this is that the user can boot the device into several
Factory RESET modes.
This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.
This patch also changes bootcmd to a special hardcoded value if Factory
RESET button was pressed during device powerup. This special bootcmd
value sets the colors of all the LEDs on the front panel to green and
then tries to load the rescue image from the SPI flash memory and boot
it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The regdomain environment variable is set according to value read from
EEPROM. This has to be done in board_late_init, after the environment
variables are read from SPI. Select CONFIG_BOARD_LATE_INIT in Kconfig
for the Turris Omnia target.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since board watchdog is now unified and not handled in board files,
remove the unnecessary includes.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Unify the way how Omnia and Mox print board information (RAM size and
serial number).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
