Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
CPU frequency reporting failed with the following error message being
printed:
sc_pm_get_clock_rate: resource:507 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QM RevB A53 at 0 MHz
Fix this by differentiating between the A35 as found on the i.MX 8QXP
and the A53 as found on the i.MX 8QM SoCs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This driver is mostly used to avoid build errors.
We use uclass clk driver for clk related operations.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
print_cpuinfo() in board init code requires uclass CPU driver,
add it to be able to display CPU info when CONFIG_DISPLAY_CPUINFO
option is enabled. CPU node in DT will have to include 'clocks'
and 'u-boot,dm-pre-reloc' properties for generic print_cpuinfo()
to work as expected. The driver outputs info for i.MX8QXP Rev A
and Rev B CPUs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add arch_cpu_init(_dm) mainly to open the channel between ACore and SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add mmu memmap, some memory regions are reserved by M4, Arm Trusted
Firmware, so need to get memreg using SCFW API and setup the memmap.
Add dram_init, dram_init_banksize, get_effective_memsize functions,
according to the memreg.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add basic cpu support, including cpu revision, cpu type,
cpu core detection.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
