In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
The sunxi MUSB glue driver has some code to check for external VBUS
presence when it's going to use the MUSB host mode, and it warns if
there is VBUS provided through the cable (in sunxi_musb_enable()).
This code was apparently copied to the USB gadget detection code
(g_dnl_board_usb_cable_connected()), but here we actually *expect*
external VBUS power, so a warning is wrong and confusing.
So far this message rarely triggered, but a recent patch (6fa41cdd19)
changed this:
===========================
=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe90000
A charger is plugged into the OTG
/A charger is plugged into the OTG
\A charger is plugged into the OTG
|A charger is plugged into the OTG
-A charger is plugged into the OTG
....
===========================
Remove the message for the gadget cable detection call, and just return
the status of the VBUS detection, as this is what the callers are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For some systems, such as the PinePhone, there is no way for the end
user to make sure the system is indeed booting before the boot script is
executed, which takes several seconds. Therefore, it can be useful to
provide early visual feedback as soon as possible.
In order achieve this goal, this patch initializes the status LED (if
configured) in the SPL.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.
This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_SOFT
CONFIG_SYS_I2C_SOFT_SPEED
CONFIG_SYS_I2C_SOFT_SLAVE
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.
By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.
Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.
Add a config option to fix it up so it can function properly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Refactor setup_environment() so we can use the created sid for a
Bluetooth address too.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.
*) for example, zynqmp uses same order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The reference design of Allwinner V3 series uses an
AXP203 or AXP209 PMIC attached to the I2C0 bus of the SoC, although the
first community-available V3s board, Lichee Pi Zero, omitted it.
Allow to introduce support for the PMIC on boards with it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Previously, fdtfile was always the value in CONFIG_DEFAULT_DEVICE_TREE.
This meant that, regardless of the DT chosen by SPL (either by changing
the header in the image or by the selection code at runtime), Linux
always used the default DT.
By using the name from the SPL header (which, because of the previous
commit, always matches the DT used by U-Boot proper), Linux also sees
the same board as U-Boot/SPL, even if the boot script later loads a DT
from disk.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: remove no longer needed CONFIG_SPL_LOAD_FIT guards]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This overwrites the name loaded from the SPL image. It will be different
if there was previously no name provided, or if a more accurate name was
determined by the board variant selection logic. This means that the DT
name in the SPL header now always matches the DT appended to U-Boot.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: move function under CONFIG_SPL_LOAD_FIT guard]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Instead of using an entirely separate matching algorithm, simply update
the name of the DT we want to match. Enabling this logic does not depend
on the FIT config name, only on the initial guess of the board name.
Importantly, the initial guess must be "sun50i-a64-pine64-plus", because
otherwise the logic would trigger when "sun50i-a64-pine64-lts" was
written to the SPL header.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This moves the validity checking and typecasts all to one place away
from the string comparison logic, and it detangles the compile-time
and runtime control flow.
The new helper will also be used by U-Boot proper in a future commit.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: protect new function with CONFIG_SPL_LOAD_FIT]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The variable "cmp_str" always leaves me wondering if it is the DT name
of the current board (yes) or DT name in the FIT config entry (no).
In preparation for expanding the functionality here, rename it to
something that obviously means "this is the DT name we are looking for".
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_idebug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.
However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.
When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.
Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Commit a8011eb84dfa("sunxi: board: Print error after power initialization
fails") moved the DRAM init after the increase of the CPU clock
frequency. This lead to various DRAM initialisation failures on some
boards (hangs or wrong size reported, on a NanoPi Duo2 and OrangePi
Zero, for instance). Lowering the CPU frequency significantly (for instance
to 408 MHz) seems to work around the problem, so this points to some timing
issues in the DRAM code.
Debugging this sounds like a larger job, so let's just revert this patch
to bring back those boards.
Beside this probably unintended change the patch just moved the error
message around, so reverting this is not a real loss.
This reverts commit a8011eb84d.
Tested-By: Priit Laes <plaes@plaes.org>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Currently during init, we enable all power, then enable the dram and
after that check whether there was an error during power-up.
This makes little sense, we should enable power and then check if power
was brought up properly before we continue to initialize other things.
This patch moves the DRAM init after the power failure check.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.
As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.
Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far we have two users which want to look at the SPL header. We will
get more in the future.
Refactor the existing SPL header checks into a common function, to
simplify reusing the code.
Now that this is easy, add proper version checks to the DT name parsing.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.
Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.
[1] https://semver.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.
Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.
On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
variables buf from board_mmc_init, and ret from misc_init_r
were unused on the functions, so remove it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so use it in board_usb_cable_connected.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
