- EBI Chip Select Register is now in SFR,
- the pins are set to default values,
- timings are matching MT29F4G08BABWP's nand flash requirements.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama5's SFR has at offset 0x04 the DDR Configuration Register,
while sam9x60's SFR contains the EBI Chip Select Register. Add
a union to reconcile both boards.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Special Function Registers (SFR) are present in sam9x5 and
sam9x60 too, rename sama5_sfr to at91_sfr.h.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
add sam9x60ek_mmc_defconfig and for now only supports booting from
sdcard.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[nicolas.ferre@microchip.com: split patch, add Ethernet controller,
phy and tools]
[claudiu.beznea@microchip.com: add CONFIG_OF_LIBFDT_OVERLAY]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[tudor.ambarus@microchip.com: Fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add new board SAM9X60-EK using the ARM926 SAM9X60 SoC.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[tudor.ambarus@microchip.com:
- fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]
- drop SPL related macros
- drop memtest macros
- drop CONFIG_SPI_BOOT, CONFIG_SYS_USE_DATAFLASH related macros
- drop inclusion of asm/arch/at91sam9_smc.h]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add Ethernet controller to dtsi file and enable it on sam9x60ek
platform connected with rmii.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
add device tree files for sam9x60ek board with below changes.
- Add initial device nodes (pmc, pinctrl, sdhc, dbgu & pit)
- Add the reg property for the pinctrl node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[prasanthi.chellakumar@microchip.com: fix style/whitespace issues]
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
[nicolas.ferre@microchip.com:
- fix gclk,
- fix pio/pinctrl controller definition and allow to have more
than only PIOA for this SoC,
- removing pinctrl address]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com:
- use SAM9X60's compatible for pinctrl
- add drive strength and slew rate options for SDMMC0 pins.]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[tudor.ambarus@microchip.com:
- u-boot,dm-pre-reloc property in dedicated file,
- fix pit len, starts from 0xFFFFFE40 and it is of len 0x10]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Fixes redefinition of CONFIG_SYS_SPI_U_BOOT_OFFS
This is now a Kconfig
Fixes: e40a9ba6d2d5 ("board: atmel: sama5d2_wlsom1_ek: add qspi support and qspi boot config")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This board has an external oscillator as MCK that does not need driving.
Bypass the driving for the main oscillator in SPL.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Remove 2017 from being printed at boot video console.
This is outdated.
To avoid this situation, remove the year completely.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add node for hlcld for u-boot logo display at boot.
This is compatible with the Precision Design Associates (PDA) TM5000 screen.
Timings are compatible with simple panel from Linux, panel name is
pda_91_00156_a0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for qspi memory on board. Created boot support for QSPI
for both u-boot proper and SPL.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
qspi1 does not have an alias/seq number. This is required for
SPL default SF bus booting for the boards that have this SoC
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a function in SFR implementation that will open the DDR input
buffers.
This can be called at DRAM initialization time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for the SAMA5D27-WLSOM1-EK. It's based on the Microchip
WireLess SoM which contains the SAMa5D27 LPDDR2 2Gbits SiP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[eugen.hristev@microchip.com]: added u-boot specific dtsi and ported to 2019.10
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The commit
642b80d256 ("net: designware: drop compatible altr, socfpga-stmmac")
breaks designware ethernet for all ARC boards. It removes
"altr, socfpga-stmmac" compatible from "drivers/net/designware.c"
without changing compatible in the boards which use it.
Fix that by adding "snps,arc-dwmac-3.70a" compatible string to
"drivers/net/designware.c" and using it in ARC boards device tree.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
With the patch below applied, host_block_dev structure was switched
to be placed in platdata rather than priv. The command "host info"
must be aligned with this change. Otherwise, we will see "Segmentation
Fault."
Fixes: 8f994c860d ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
These boards don't have a watchdog enabled in SPL, so make sure
CONFIG_SPL_WDT is not enabled.
Fixes: commit 6874cb7220 ("watchdog: Split WDT from SPL_WDT")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Assorted TI platform fixes
- Revert the change that broke environment flag validation
- Assorted typo fixes
- Assorted Kconfig dependency fixes
- Other minor bug fixes
This reverts commit 7d4776545b. The
changes here break environment validation and furthermore do not seem to
be required.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <aford173@gmail.com>
Existing debug output is mixed with the function name:
initcall_run_list() initcall: 25263initcall_run_list() (relocated to 425263)
Turn it to:
initcall_run_list() initcall: 25263 (relocated to 425263)
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
At this point we are using part number sub-command to retrieve UUID
of the partition using it's name.
e.g.:
part number mmc $mmcdev system_a system_a_index
part uuid mmc $mmcdev:${system_a_index} system_a_uuid
Since 'part uuid' sub-command expects partition index in hex format and
'part number' returns decimal value, 'part uuid' command will provide
wrong UUID or fail.
Fixes: be683756f6 ("cmd: part: Add 'number' sub-command")
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Pontus Fuchs <pontus.fuchs@se.bosch.com>
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
To accommodate the growth of u-boot, we need to shift the location of the
secure monitor. Moving it 64kB further.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
On HS devices the access to TRNG is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This updates MAINTAINERS and git-mailrc to add me as maintainer for
socfpga.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
*.pyc files contain compiled Python bytecode. 'make mrproper' should remove
them.
Removing *.pyc files helps for instance sometimes when running into an
error "binman: Unknown entry type 'blob' in node '/binman/blob'".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 269000 bytes but now needs to be grown to 276000 to make room
for the signatures attached to the board configuration data on High
Security devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
