Commit graph

1921 commits

Author SHA1 Message Date
Frieder Schrempf
2a79775069 mtd: spi-nor-ids: Add support for Macronix MX25V8035F and MX25R1635F
The MX25V8035F is a 8Mb SPI NOR flash and the MX25R1635F is very
similar, but has twice the size (16Mb) and supports a wider supply
voltage range.

They were tested on the Kontron Electronics i.MX6UL and i.MX8MM SoMs.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2021-07-10 15:59:20 +02:00
Tom Rini
570c3dcfc1 arm: Remove spear600 boards and the rest of SPEAr support
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM.  Remove them.  As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.

Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 22:22:42 -04:00
Patrick Delaunay
b953ec2bca dm: define LOG_CATEGORY for all uclass
Define LOG_CATEGORY for all uclass to allow filtering with
log command.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-06 10:38:03 -06:00
Takahiro Kuwano
5b8ec59e2a mtd: spi-nor-tiny: Add fixups for Cypress s25hl-t/s25hs-t
Fixes mode clocks for SPINOR_OP_READ_FAST_4B in tiny.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
1c3dd193b5 mtd: spi-nor-core: Add fixups for Cypress s25hl-t/s25hs-t
The nor->ready() and spansion_sr_ready() introduced earlier in this
series are used for multi-die package parts.

The nor->quad_enable() sets the volatile QE bit on each die.

The nor->erase() is hooked if the device is not configured to uniform
sectors, assuming it has 32 x 4KB sectors overlaid on bottom address.
Other configurations, top and split, are not supported at this point.
Will submit additional patches to support it as needed.

The post_bfpt/sfdp() fixes the params wrongly advertised in SFDP.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
72151ad10f mtd: spi-nor-core: Add Cypress manufacturer ID in set_4byte
Cypress chips support SPINOR_OP_EN4B(B7h) to enable 4-byte addressing mode.

Cypress chips support B8h to disable 4-byte addressing mode instead of
SPINOR_OP_EX4B(E9h).

This patch defines new opcode and updates set_4byte() to support
enable/disable 4-byte addressing mode for Cypress chips.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
d2d79895da mtd: spi-nor-core: Read status by Read Any Register
The spansion_sr_ready() reads status register 1 by Read Any Register
commnad. This function is called from Flash specific hook with die address
and dummy cycles to support multi-die package parts from Spansion/Cypress.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
24b1e2c690 mtd: spi-nor-core: Add the ->ready() hook
For dual/quad die package devices from Spansion/Cypress, the device's
status needs to be checked by reading status registers in all dies, by
using Read Any Register command. To support this, a Flash specific hook
that can overwrite the legacy status check is needed.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
a4aa9b7522 mtd: spi-nor-core: Add support for volatile QE bit
Some of Spansion/Cypress chips support volatile version of configuration
registers and it is recommended to update volatile registers in the field
application due to a risk of the non-volatile registers corruption by
power interrupt. This patch adds a function to set Quad Enable bit in CFR1
volatile.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
2d20f34485 mtd: spi-nor-core: Add support for Read/Write Any Register
Some of Spansion/Cypress chips support Read/Write Any Register commands.
These commands are mainly used to write volatile registers and access to
the registers in second and subsequent die for multi-die package parts.

The Read Any Register instruction (65h) is followed by register address
and dummy cycles, then the selected register byte is returned.

The Write Any Register instruction (71h) is followed by register address
and register byte to write.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Takahiro Kuwano
c95a914aed mtd: spi-nor-ids: Add Cypress s25hl-t/s25hs-t
The S25HL-T/S25HS-T family is the Cypress Semper Flash with Quad SPI.

https://www.cypress.com/file/424146/download (256Mb/512Mb/1Gb, single die)
https://www.cypress.com/file/499246/download (2Gb/4Gb, dual/quad die)

The full version can be found in the following links (registration
required).
https://community.cypress.com/t5/Semper-Flash-Access-Program/Datasheet-Semper-Flash-with-Quad-SPI/ta-p/260789?attachment-id=19522
https://community.cypress.com/t5/Semper-Flash-Access-Program/Datasheet-2Gb-MCP-Semper-Flash-with-Quad-SPI/ta-p/260823?attachment-id=29503

S25HL/HS-T (Semper Flash with Quad SPI) Family has user-configurable
sector architecture. By default, the 512Mb and 1Gb, single-die package
parts are configured to non-uniform that 4KB sectors overlaid on bottom
address. To support this, an erase hook makes overlaid sectors appear as
uniform sectors. The 2Gb, dual-die package parts are configured to uniform
by default.

Tested on Xilinx Zynq-7000 FPGA board.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-29 19:16:54 +05:30
Pratyush Yadav
f6adec1af4 mtd: spi-nor-core: Allow using Micron mt35xu512aba in Octal DTR mode
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.

Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:06:57 +05:30
Pratyush Yadav
ea9a22f7e7 mtd: spi-nor-core: Add support for Cypress Semper flash
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.

The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.

The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:06:43 +05:30
Takahiro Kuwano
ee52b0b764 mtd: spi-nor-core: Add non-uniform erase for Spansion/Cypress
Some of Spansion/Cypress chips have overlaid 4KB sectors at top and/or
bottom, depending on the device configuration, while U-Boot supports
uniform sector layout only.

The spansion_erase_non_uniform()  erases overlaid 4KB sectors,
non-overlaid portion of normal sector, and remaining normal sectors, by
selecting correct erase command and size based on the address to erase
and size of overlaid portion in parameters. Since different Spansion
flashes can use different opcode for erasing the 4K sectors, the opcode
must be passed in as a parameter based on the flash being used.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[p.yadav@ti.com: Refactor the function to be compatible with nor->erase,
make 4K opcode customizable, call spi_nor_setup_op() before executing
the op.]
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:06:07 +05:30
Pratyush Yadav
aba0bcd7bd mtd: spi-nor-core: allow truncated erases
On devices with non-uniform sector sizes like Spansion S25 or S28 family
of flashes the sector under erase does not necessarily have to be
mtd->erasesize bytes long. For example, on S28 flashes the first 128 KiB
region is composed of 32 4 KiB sectors, then a 128 KiB sector, and then
256 KiB sectors till the end.

Let the flash-specific erase functions erase less than the requested
length in case of the 4 or 128 KiB sectors and report the number of
bytes erased back to the calling function.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:05:38 +05:30
Pratyush Yadav
0be8ab1f16 mtd: spi-nor-core: Perform a Soft Reset on boot
When the flash is handed to us in a stateful mode like 8D-8D-8D, it is

difficult to detect the mode the flash is in. One option is to read SFDP
in all modes and see which one gives the correct "SFDP" signature, but
not all flashes support SFDP in 8D-8D-8D mode.

Further, even if you detect the mode of the flash via SFDP, you still
have the problem of actually reading the ID. The Read ID command is not
standardized across flash vendors. Flashes can have different dummy
cycles needed for reading the ID. Some flashes even expect a 4-byte
dummy address with the Read ID command. All this information cannot be
obtained from the SFDP table.

So, perform a Software Reset sequence before reading the ID and
initializing the flash. A Soft Reset will bring back the flash in its
default protocol mode assuming no non-volatile configuration was set.
This will let us detect the flash even if ROM hands it to us in Octal
DTR mode.

To accommodate cases where there is more than one flash on a board, and
only one of them needs a soft reset, failure to reset is not made fatal,
and we still try to read ID if possible.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:05:17 +05:30
Pratyush Yadav
575caf4500 mtd: spi-nor-core: Perform a Soft Reset on shutdown
On probe, the SPI NOR core will put a flash in 8D-8D-8D mode if it
supports it. But Linux as of now expects to get the flash in 1S-1S-1S
mode. Handing the flash to Linux in Octal DTR mode means the kernel will
fail to detect the flash.

So, we need to reset to Power-on-Reset (POR) state before handing off
the flash. A Software Reset command can be used to do this.

One limitation of the soft reset is that it will restore state from
non-volatile registers in some flashes. This means that if the flash was
set to 8D mode in a non-volatile configuration, a soft reset won't help.
This commit assumes that we don't set any non-volatile bits anywhere,
and the flash doesn't have any non-volatile Octal DTR mode
configuration.

Since spi-nor-tiny doesn't (and likely shouldn't) have
spi_nor_soft_reset(), add a dummy spi_nor_remove() for it that does
nothing.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:04:53 +05:30
Pratyush Yadav
a1122a3d98 mtd: spi-nor-core: Detect Soft Reset sequence support from BFPT
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:04:30 +05:30
Pratyush Yadav
b058f108d7 mtd: spi-nor-core: Do not make invalid quad enable fatal
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").

While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing assuming there is no quad
enable bit present.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:04:09 +05:30
Pratyush Yadav
6b808e0864 mtd: spi-nor-core: Enable octal DTR mode when possible
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:03:57 +05:30
Pratyush Yadav
b862765c7c mtd: spi-nor-core: Prepare Read SR and FSR for Octal DTR mode
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in Octal DTR mode.
Use that information to send the correct Read SR command.

Some controllers might have trouble reading just 1 byte in DTR mode. So,
when we are in DTR mode read 2 bytes and discard the second. This shows
no side effects with the two flashes I tested: Micron mt35xu512aba and
Cypress s28hs512t.

Update Read FSR to mimic Read SR because they share the same
characteristics.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:02:39 +05:30
Pratyush Yadav
4d40e82663 mtd: spi-nor-core: Parse xSPI Profile 1.0 table
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
the number of dummy cycles needed for a Read Status Register command,
and the number of address bytes needed for a Read Status Register
command.

The default dummy cycles for a fast octal DTR read are set to 20. Since
there is no simple way of determining the dummy cycles needed for the
fast read command, flashes that use a different value should update it
in their flash-specific hooks.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:02:01 +05:30
Pratyush Yadav
9ec5ea0127 mtd: spi-nor-core: Get command opcode extension type from BFPT
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:01:15 +05:30
Pratyush Yadav
22ae535b7d mtd: spi-nor-core: prepare BFPT parsing for JESD216 rev D
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.

The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.

So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:01:00 +05:30
Pratyush Yadav
95954f55e9 mtd: spi-nor-core: Add support for DTR protocol
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.

Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 12:00:32 +05:30
Pratyush Yadav
6182d15b3e mtd: spi-nor-core: Do not set data direction when there is no data
Even when spi_nor_write_reg() has no data to write, like when executing
a write enable operation, it sets the data direction to
SPI_MEM_DATA_OUT. This trips up spi_mem_check_buswidth() because it
expects a data phase when there is none. Make sure the data direction is
set to SPI_MEM_NO_DATA when there is no data to write.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:59:47 +05:30
Pratyush Yadav
71025f013c mtd: spi-nor-core: Rework hwcaps selection
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.

Rework the hwcaps selection logic to use spi_mem_supports_op().

To make sure the build doesn't break for boards not using CONFIG_DM_SPI,
add a simple SPI_{RX,TX}_ based hwcaps selection logic in spi-mem-nodm
similar to spi_mem_default_supports_op(). This change is only
compile-tested.

To avoid SPL size problems on the x530 board, the old hwcaps selection
is still kept around. Leaving the code in-place was getting difficult to
read and understand, so the code is restructured to have it all in one
isolated function. As a result of this, the parameter hwcaps to
spi_nor_setup() is no longer needed. Remove it.

Based on the Linux commit c76f5089796a (mtd: spi-nor: Rework hwcaps
selection for the spi-mem case, 2019-08-06)

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:59:35 +05:30
Pratyush Yadav
8702188ce5 mtd: spi-nor-core: Introduce flash-specific fixup hooks
Sometimes the information in a flash's SFDP tables is wrong. Sometimes
some information just can't be expressed in the SFDP table. So,
introduce the fixup hooks to allow tailoring settings for a specific
flash.

Three hooks are added: default_init, post_sfdp, and post_bfpt. These
allow tweaking the flash settings at different point in the probe
sequence. Since the hooks reside in nor->info, set that value just
before the call to spi_nor_init_params().

The hooks and at what points they are executed mimics Linux's spi-nor
framework. One major difference is that Linux puts the struct
spi_nor_fixups in nor->info. This is not possible in U-Boot because the
spi-nor-ids list is shared between spi-nor-core.c and spi-nor-tiny.c.
Since spi-nor-tiny shouldn't have those fixup hooks populated, add a
separate function that lets flashes populate their fixup hooks.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:59:10 +05:30
Pratyush Yadav
e2e31fa680 mtd: spi-nor-core: Move SFDP related declarations to top
These structures will be used in a later commit inside another structure
definition. Also take the declarations out of the ifdef since they won't
affect the final binary anyway and will be used in a later commit.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:58:46 +05:30
Pratyush Yadav
18b0de0f3b mtd: spi-nor-core: Add a ->setup() hook
nor->setup() can be used by flashes to configure settings in case they
have any peculiarities that can't be easily expressed by the generic
spi-nor framework. This includes things like different opcodes, dummy
cycles, page size, uniform/non-uniform sector sizes, etc.

Move related declarations to avoid forward declarations.

Inspired by the Linux kernel's setup() hook.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:58:10 +05:30
Pratyush Yadav
1af0334ab4 mtd: spi-nor-core: Fix address width on flash chips > 16MB
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.

The check in spi_nor_scan() doesn't catch it because addr_width did get
set. This fixes that check.

Ported from Kernel commit 324f78dfb442b82365548b657ec4e6974c677502.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:57:46 +05:30
Marek Behún
dcb9a80359 mtd: compare also with OF path and device name in get_mtd_device_nm()
The get_mtd_device_nm() function (code imported from Linux) simply
iterates all registered MTD devices and compares the given name with
all MTDs' names.

With SPI_FLASH_MTD enabled U-Boot registers a SPI-NOR as a MTD device
with name identical to the SPI flash chip name (from SPI ID table). Thus
for a board with multiple same SPI-NORs it registers multiple MTDs, but
all with the same name (such as "s25fl164k"). We do not want to change
this behaviour, since such a change could break existing boot scripts,
which can rely on a hardcoded name.

In order to allow somehow to uniqely select a MTD device, change
get_mtd_device_nm() function as such:
- if first character of name is '/', try interpreting it as OF path
- otherwise compare the name with MTDs name and MTDs device name.

In the following example a board has two "s25fl164k" SPI-NORs. They both
have name "s25fl164k", thus cannot be uniquely selected via this name.
With this change, the user can select the second SPI-NOR either with
"spi-nor@1" or "/soc/spi@10600/spi-nor@1".

Example:
  => mtd list
  List of MTD devices:
  * s25fl164k
    - device: spi-nor@0
    - parent: spi@10600
    - driver: jedec_spi_nor
    - path: /soc/spi@10600/spi-nor@0
    - type: NOR flash
    - block size: 0x1000 bytes
    - min I/O: 0x1 bytes
    - 0x000000000000-0x000000800000 : "s25fl164k"
  * s25fl164k
    - device: spi-nor@1
    - parent: spi@10600
    - driver: jedec_spi_nor
    - path: /soc/spi@10600/spi-nor@1
    - type: NOR flash
    - block size: 0x1000 bytes
    - min I/O: 0x1 bytes
    - 0x000000000000-0x000000800000 : "s25fl164k"

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
2021-06-24 11:54:57 +05:30
Marek Behún
3c58c79b5f mtd: probe SPI NOR devices in mtd_probe_devices()
In order for `mtd list` U-Boot command to list SPI NOR devices without
the need to run `sf probe` before, we have to probe SPI NOR devices in
mtd_probe_devices().

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
2021-06-24 11:54:32 +05:30
Marek Behún
69e57c4753 mtd: remove mtd_probe() function
The device_probe() function does the same thing as mtd_probe() and
mtd_probe() is only used in mtd_probe_uclass_mtd_devs(), where the
probing can be made simpler by using uclass_foreach_dev_probe macro.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
2021-06-24 11:54:07 +05:30
Marek Behún
2d1a9a6b26 mtd: spi-nor: fill-in mtd->dev member
Fill in mtd->dev member with nor->dev.

This can be used by MTD OF partition parser.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
2021-06-24 11:53:50 +05:30
Marek Behún
b7f060565e mtd: spi-nor: allow registering multiple MTDs when DM is enabled
Currently when the SPI_FLASH_MTD config option is enabled, only one SPI
can be registered as MTD at any time - it is the last one probed (since
with old non-DM model only one SPI NOR could be probed at any time).

When DM is enabled, allow for registering multiple SPI NORs as MTDs by
utilizing the nor->mtd structure, which is filled in by spi_nor_scan
anyway, instead of filling a separate struct mtd_info.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
2021-06-24 11:53:31 +05:30
Marek Behún
dc339bf784 mtd: add support for parsing partitions defined in OF
Add support for parsing partitions defined in device-trees via the
`partitions` node with `fixed-partitions` compatible.

The `mtdparts`/`mtdids` mechanism takes precedence. If some partitions
are defined for a MTD device via this mechanism, the code won't register
partitions for that MTD device from OF, even if they are defined.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
2021-06-24 11:53:15 +05:30
Jaime Liao
b388af9af4 mtd: spinand: macronix: Add support for serial NAND flash
Macronix NAND Flash devices are available in different configurations
and densities.

MX"35" means SPI NAND
MX35"UF" , UF meands 1.8V
MX35LF"2G" , 2G means 2Gbits
MX35LF2G"E4" , E4 means internal ECC and Quad I/O(x4)

MX35UF4GE4AD/MX35UF2GE4AD/MX35UF1GE4AD are 1.8V 4G/2Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7983/MX35UF4GE4AD,%201.8V,%204Gb,%20v0.00.pdf

MX35UF2GE4AC/MX35UF1GE4AC are 1.8V 2G/1Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7974/MX35UF2GE4AC,%201.8V,%202Gb,%20v1.0.pdf

Validated via normal(default) and QUAD mode by read, erase, read back,
on Xilinx Zynq PicoZed FPGA board which included Macronix
SPI Host(drivers/spi/spi-mxic.c).

Signed-off-by: Jaime Liao <jaimeliao@mxic.com.tw>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-24 11:42:52 +05:30
zhengxun
06abbef27a mtd: spi-nor-ids: Add Macronix MX66UW2G345G
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence,
add SPI_NOR_OCTAL_READ flag for this flash.

Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: change order of id flags]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
2021-06-22 13:53:24 +05:30
Yifeng Zhao
b12dc5d6fa mtd: nand: NFC drivers for RK3308, RK2928 and others
This driver supports Rockchip NFC (NAND Flash Controller) found on
RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been
tested using 8-bit NAND interface on the ARM based RK3308 platform.

Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
	ECC: 16/40/60/70 bits/1KB.
	CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
	ECC: 16 bits/1KB.
	CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
	ECC: 16/24/40/60 bits/1KB.
	CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
	ECC: 16/24/40/60 bits/1KB.
	CLOCK: ahb.

Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)

Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to
  use  the BBT(bad block table).

Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-06-18 14:37:20 +08:00
Tom Rini
a94b2aad05 First set of u-boot-atmel features for the 2021.10 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
 oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
 hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
 Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
 PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
 kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
 KxwN
 =/I5V
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next

First set of u-boot-atmel features for the 2021.10 cycle:

This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
2021-06-17 11:46:44 -04:00
Kai Stuhlemmer (ebee Engineering)
32cc2368f8 nand: atmel: Correct bitflips in erased pages
Not correcting anything in case of empty ECC data area
is not an appropriate strategy, because an uncorrected bit-flip
in an empty sector may cause upper layers (namely UBI) fail to work
properly. Therefore the approach chosen in Linux kernel and other
u-boot mtd drivers has been adopted, where a heuristic implemented
by nand_check_erased_ecc_chunk() is used in order to detect and
correct empty sectors.

Tested with sama5d3_xplained and sam9x60-ek.

Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
[ta: reorder if conditions, change commit subject, s/uint8_t/u8.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2021-06-07 11:01:40 +03:00
Marek Behún
28d476eada ARM: fix LTO for apf27
When apf27_defconfig is built with LTO, linking complains about
undefined reference to `nand_boot`. This is because it is referenced
from inline assembly. Make it visible.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
2021-05-24 14:21:30 -04:00
Marek Vasut
94657482f3 mtd: cfi: Fix PPB lock status readout
According to S26KL512S datasheet [1] and S29GL01GS datasheet [2],
the procedure to read out PPB lock bits is to send the PPB Entry,
PPB Read, Reset/ASO Exit. Currently, the code does send incorrect
PPB Entry, PPB Read and Reset/ASO Exit is completely missing.

The PPB Entry sent is implemented by sending flash_unlock_seq()
and flash_write_cmd(..., FLASH_CMD_READ_ID). This translates to
sequence 0x555:0xaa, 0x2aa:0x55, 0x555:0x90=FLASH_CMD_READ_ID.
However, both [1] and [2] specify the last byte of PPB Entry as
0xc0=AMD_CMD_SET_PPB_ENTRY instead of 0x90=FLASH_CMD_READ_ID,
that is  0x555:0xaa, 0x2aa:0x55, 0x555:0xc0=AMD_CMD_SET_PPB_ENTRY.
Since this does make sense, this patch fixes it and thus also
aligns the code in flash_get_size() with flash_real_protect().

The PPB Read returns 00h in case of Protected state and 01h in case
of Unprotected state, according to [1] Note 83 and [2] Note 17, so
invert the result. Moreover, align the arguments with similar code
in flash_real_protect().

Finally, Reset/ASO Exit command should be executed to exit the PPB
mode, so add the missing reset.

[1] https://www.cypress.com/file/213346/download
    Document Number: 001-99198 Rev. *M
    Table 40. Command Definitions, Nonvolatile Sector Protection
    Command Set Definitions
[2] https://www.cypress.com/file/177976/download
    Document Number: 001-98285 Rev. *R
    Table 7.1 Command Definitions, Nonvolatile Sector Protection
    Command Set Definitions

Fixes: 03deff433e ("cfi_flash: Read PPB sector protection from device for AMD/Spansion chips")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-04-28 10:29:36 +02:00
Farhan Ali
c146de4872 mtd: Update fail_addr when erase fails due to bad blocks
For all other erase failures, the fail_addr is updated with the
failing address. Only in the case of erase failure due to bad block
detection, the fail_addr is not updated. This change simply updates
the fail_addr for this specific scenario so that it is consistent with
the rest of the code.

Signed-off-by: Farhan Ali <farhan.ali@broadcom.com>
2021-04-12 17:17:11 -04:00
Tim Harvey
aa0032f672 spl: fit: nand: allow for non-page-aligned elements
Add a weak nand_get_mtd function for nand drivers to provide mtd info
and use this to set pagesize such that reading of non page-aligned
elements can succeed.

The spl_load_simple_fit already handles block block access so all we
need to do is provide the nand writesize as the block length.

Further cleanup of the drivers which use nand_spl_loaders.c such as
am335x_spl_bch.c, atmel_nand.c, and nand_spl_simple.c could be done
using info from mtd_info instead of statically defined details.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-04-08 20:29:53 +02:00
Jagannadha Sutradharudu Teki
53879b1738 cfi_flash: Fix detection of 8-bit bus flash devices via address shift
We had a problem detecting 8/16bit flash devices connected only via
8bits to the SoC for quite a while. Commit 239cb9d9
[mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support] finally
fixed this 8-bit bus support. But also broke some other boards using
this cfi driver. So this patch had to be reverted.

I spotted a different, simpler approach for this 8-bit bus support
on the barebox mailing list posted by
Oleksij Rempel <bug-track@fisher-privat.net>:

http://www.spinics.net/lists/u-boot-v2/msg14687.html

Here the commit text:

"
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
"

This patch now is a port of this barebox patch to U-Boot.

Along with the change w.r.t from barebox,
Some flash chips can support multiple bus widths, override the
interface width and limit it to the port width.

Tested on 16-bit Spansion flash on sequoia.
Tested 8-bit flashes like 256M29EW, 512M29EW.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-04-06 08:55:53 +02:00
Tom Rini
1057b1be75 Prepare v2021.04-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmBiRbMACgkQFHw5/5Y0
 tyz0KAv/T8glQGL6L2CYeLuwbs9tndQoaH2YNb3teNUJrqehBleJAQ6ubHP30d87
 rHrokJ4Zu3TC15sACrK4GOMvsAVkeCuU/jIqFJA4ieDZr8g7yfUMOZMsDiIFdd36
 Rdmi71Jtek/csyS5BfcUUYoXVbUCGQ8yAx7z0VrK0sqsqZYYJNwPmqgkR8U2ulNb
 FiLxwamFwH7+bsvcvHajO1dOyko0zR7GTisf/fOgmlHuF3BldqG4SDcNd528uEWb
 r3fXs2Ut6IaC/beCnmKUPVG3ZjdPtb+T230rRRhUOfjTwqR7SzXp5bTyzdgyw3gU
 rOgfi/mAGQPPG2E2fzPz0JCI1irbnkSE2fVJ4epaVUCoHIEsQQdy034aD3qLcHFY
 65ihEpRvCM7s9jfKX8XeIG4rKFB4i60TX5orzdMvx7wV3rxmPE9qQmF9lkD+fEA+
 TPuFtkjGmluSe+xWBVK7+6xuF6rcLEbNXuFWRi3qMSMgH8rtGfeJRonusOGPolwC
 jQ1T7szW
 =UJ/O
 -----END PGP SIGNATURE-----

Merge tag 'v2021.04-rc5' into next

Prepare v2021.04-rc5
2021-03-29 18:00:21 -04:00
Simon Glass
b3b60f5912 sf: Support querying write-protect
This feature was dropped from U-Boot some time ago:

   f12f96cfaf (sf: Drop spl_flash_get_sw_write_prot")

However, we do need a way to see if a flash device is write-protected,
since if it is, it may not be possible to write to do (i.e. failing to
write is expected).

I am not sure of the correct layer to implement this, so this patch is a
stab at it. If spi-flash makes sense then I will add to the 'sf' also.

Re the points mentioned in the removal commit:

    1) This kind of requirement can be achieved using existing
       flash operations and flash locking API calls instead of
       making a separate flash API.

Which uclass is this?

    2) Technically there is no real hardware user for this API to
       use in the source tree.

I do want coral (at least) to support this.

    3) Having a flash operations API for simple register read bits
       also make difficult to extend the flash operations.

This new patch only mentions write-protect being on or off, rather than
the actual mechanism.

    4) Instead of touching generic code, it is possible to have
       this functionality inside spinor operations in the form of
       flash hooks or fixups for associated flash chips.

That sounds to me like what drivers are for. But we still need some sort
of API for it to be accessible.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 15:04:31 +13:00
Heinrich Schuchardt
b09c74f66d mtd: spi_flash_free()
dfu_free_entities() invoking dfu_free_entity_sf() has let to segementation
faults due to double freeing the same device.

spi_flash_free() is not relevant for the driver model but exists only for
compatibility with old drivers.

We must not remove any device here:

* The device may still be referenced.
* We don't want to have to probe again.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-03-27 13:59:36 +13:00