Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig) and supports resets for each of the
lanes.
This is an adaptation of the linux driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
Add a Sierra PHY driver with PCIe and USB support.
This driver is a port from the mainline linux driver.
The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.
There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself. Additionally there are
resets for each PHY lane.
The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.
The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required) for each lane
group, and then enable the PHY. Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
One difference with the linux driver is that the PHY is
always reset after it is powered-on. This is because role
switching is not supported in u-boot and the cable
orientation is handled by the PHY reset.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com
Read the strobe select value from the device tree property ti,strobe-sel,
required for HS400 speed mode
Fixes: a20008eabd ("mmc: am654_sdhci: Add Support for configuring PHY in J721e")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210525093826.10390-2-a-govindraju@ti.com
CONFIG_SYSRESET_CMD_POWEROFF defines do_poweroff() in sysreset-uclass.c
that's why don't define it twice when both CONFIG_SYSRESET_CMD_POWEROFF and
CONFIG_CMD_POWEROFF are enabled. CONFIG_SYSRESET_CMD_POWEROFF depends on
CONFIG_CMD_POWEROFF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for xilinx multirate(MRMAC) ethernet driver.
This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC.
Added support for 4 ports of MRMAC for speeds 10G and 25G.
MCDMA supports upto 16 channels but in this driver we have setup only
one channel which is enough.
Tested 10G and 25G on all 4 ports.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
lpd_lsbus is clock which is used by many IPs like dmas, gems, gpio, sdhcis,
spis, ttcs, uarts, watchdog that's why make sense to also enable access to
change this clock. For this clock you already get the rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these variables/structure are local and should be static.
Issues are reported by sparse:
drivers/mmc/zynq_sdhci.c:49:11: warning: symbol 'zynqmp_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:50:11: warning: symbol 'zynqmp_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:53:11: warning: symbol 'versal_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:54:11: warning: symbol 'versal_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:546:24: warning: symbol 'arasan_ops' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix these kernel doc warnings:
drivers/mmc/zynq_sdhci.c:181: warning: contents before sections
drivers/mmc/zynq_sdhci.c:236: warning: contents before sections
drivers/mmc/zynq_sdhci.c:291: warning: contents before sections
drivers/mmc/zynq_sdhci.c:297: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sdcardclk_set_phase'
drivers/mmc/zynq_sdhci.c:354: warning: contents before sections
drivers/mmc/zynq_sdhci.c:360: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sampleclk_set_phase'
drivers/mmc/zynq_sdhci.c:467: warning: contents before sections
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Restrict tap_delay value to the allowed size(8bits for itap and 6 bits
for otap) before writing to the tap delay register.
Clear ITAP and OTAP delay bits before updating with the new tap value
for Versal platform.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Allow configuring ITAP and OTAP values with zero to avoid failures in
some cases (one of them is SD boot mode). Legacy, SDR12 modes require
to program the ITAP and OTAP values as zero, whereas for SDR50 and SDR104
modes ITAP value is zero.
In SD boot mode firmware configures the SD ITAP and OTAP values and
in this case u-boot has to re-configure required tap values(including zero)
based on the operating mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
set_phase() functions are not modifying the ret value and returning
the same uninitialized ret, return 0 instead.
Keep the return type as int to return errors when the tapdelay's are
set via xilinx_pm_request() in future.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit b81406db51 ("arm: serial: Add debug UART capability to the
pl01x driver") add supports to use pl01x as a debug UART. However,
due to CONFIG_IS_ENABLED macro requires CONFIG_SPL_* prefix, the
_debug_uart_init() would not choose TYPE_PL011 in SPL build. This
patch fixes the bug by judging CONFIG_DEBUG_UART_PL011 explicitly.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Simon Glass <sjg@chromium.org>
pl01x_putc() might return -EAGAIN if there was no space in FIFO. In that
case, high-level caller should wait until there is space and resend the
character.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some reason, the DragonBoard 410c aborts autoboot immediately if
U-Boot is started without LK. It looks like it picks up a single broken
character via serial and therefore believes a key was pressed to abort
autoboot.
After some debugging, it seems like adding some delay after pinctrl
setup but before UART initialization fixes the issue. It's also worth
mentioning that unlike when booting from LK, the pinctrl setup is
actually necessary when booting U-Boot without LK since UART is broken
if the pinctrl line is removed.
I suspect that reconfiguring the pins might take some time to stabilize
and if the UART controller is enabled too quickly it will pick up some
random noise. Adding a few milliseconds of delay fixes the issue and
shouldn't have any other negative side effects.
3ms seems to be the minimum delay required in my tests, use 5ms instead
just to be sure.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
RTC devices could provide battery-backed memory that can be used for
storing the reboot mode magic value.
Add a new reboot-mode back-end that uses RTC to store the reboot-mode
magic value. The driver also supports both endianness modes.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A use case for controlling the boot mode is when the user wants
to control the device boot by pushing a button without needing to
go in user-space.
Add a new backed for reboot mode where GPIOs are used to control the
reboot-mode. The driver is able to scan a predefined list of GPIOs
and return the magic value. Having the modes associated with
the magic value generated based on the GPIO values, allows the
reboot mode uclass to select the proper mode.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A new driver uclass is created to handle the reboot mode control.
The new uclass driver is updating an environment variable with the
configured reboot mode. The mode is extracted from a map provided
at initialization time. The map contains a list of modes
and associated ids.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch add support for using NXP's pca8574 I2C IO expander, which
has only 8 IO lines.
After this change the .data member's information from struct udevice_id
are used to either sent one or two bytes.
Moreover, the '_le16' suffix from pcf8575_i2c_{write|read}_le16()
functions have been removed as now we also sent 8 bit data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Those members are not used anymore as ones from gpio_dev_priv
structure (when DM_GPIO support is enabled) are used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This change ensures both U-Boot and OP-TEE see the same content
from shared memory when OP-TEE is invoked prior U-Boot relocation.
This change is required since U-Boot may execute with data cache off
while OP-TEE always enables cache on memory shared with U-Boot.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The result of dpio_close() is actually taken into account.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Change the reg variable to not be unsigned so that we not get into an
unsigned compared against 0.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a common empty ops: eqos_null_ops() to remove the duplicated empty
functions and reduce the driver size for stm32 and imx config.
This patch also aligns the prototype of ops 'eqos_stop_clks' with other
eqos ops by adding return value.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the generic ethernet phy which already manages the correct binding
for gpio reset, including the assert an deassert delays.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since the commit commit 6a895d039b ("net: Update eQos driver and FEC
driver to use eth phy interfaces") the field phyaddr of driver private data
struct eqos_priv is no more used in eqos_start() for the phy_connect()
parameter.
Now this variable is only initialized in eqos_probe_resources_stm32()
it can be removed.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Bind any subnode with name beginning by mdio, mdio0 for example,
and not only the "mdio" as namei of subnode.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace debug trace and printf to log macros:
- debug() replaced by dev_dbg() when device is available, this macro
indicate the device name since commit ceb70bb870 ("dm: Print device
name in dev_xxx like Linux")
- printf() replaced by log_notice() to allow dispatch to log backends.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The gpio reset and the assert or deassert delay are defined in generic
binding of the ethernet phy in Linux:
Documentation/devicetree/bindings/net/ethernet-phy.yaml
reset-gpios:
maxItems: 1
description:
The GPIO phandle and specifier for the PHY reset signal.
reset-assert-us:
description:
Delay after the reset was asserted in microseconds. If this
property is missing the delay will be skipped.
reset-deassert-us:
description:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
See also U-Boot: doc/device-tree-bindings/net/phy.txt
This patch adds the parsing of this common DT properties in the
u-class "eth_phy_generic", used by default in the associated driver
"eth_phy_generic_drv"
This parsing function eth_phy_of_to_plat can be reused by other
ethernet phy drivers for this uclass UCLASS_ETH_PHY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use same type as eth_device->iobase and support addresses greater
than INT_MAX.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Fixed a defect of a null pointer being discovered by Coverity Scan:
CID 331544: Null pointer dereferences (REVERSE_INULL)
Null-checking "size" suggests that it may be null, but it has already been
dereferenced on all paths leading to the check.
Signed-off-by: Chen Guanqiao <chenguanqiao@kuaishou.com>
It is useful to be able to iterate over block devices. Typically there
are fixed and removable devices. For security reasons it is sometimes
useful to ignore removable devices since they are under user control.
Add iterators which support selecting the block-device type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for reading devicetree flags for MMC devices. With this we
can distinguish between fixed and removable drives. Note that this
information is only available when the device is probed, not when it is
bound, since it is read in the of_to_plat() method. This could be changed
if needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rather than calling directly into the sandbox SDL code, we can use the
normal U-Boot console handling for this feature. Update the code, to make
it more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to read this information from the EC. It is useful for
determining whether the battery has enough charge to boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Renesas R-Car Gen3 development kits contain board ID EEPROM.
This driver parses out the board ID and revision out of that
EEPROM and exports it e.g. for the board-info print on boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Simon Glass <sjg@chromium.org>
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
