Finally, found the root cause of the issue already once mentioned back
here [2] which caused the following error message during boot:
imx_wdt watchdog@30280000:
pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Turns out while the watchdog node itself was already u-boot,dm-spl its
pinctrl node was not which caused it to be unavailable at that early
stage. Note that any and all other boards I checked also seem to be
missing this. However, I can't judge whether or not they might indeed
need a similar fix or not.
[2] https://marc.info/?l=u-boot&m=161786572422973
Fixes: commit d304e7ace3
("ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This powers some peripherals on the carrier board e.g. the USB hub.
Related-to: ELB-3206
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Prepare for DEK blob encapsulation support through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application
call. U-boot sends and receives the DEK and the DEK blob binaries
through OP-TEE dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Taken from NXP's commit 56d2050f40 ("imx8m: Add DEK blob encapsulation
for imx8m").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The devicetree submitted and approved for the mainline linux kernel is
slightly different than the one present here. This syncs both
devicetrees (for the Rockchip SFC node at least) present on the PX30
and the Odroid Go Advance. Changes include renaming the flash node,
reordering the values in the SFC node for the rk3326-odroid-go2,
changing the name of the cs pinctrl node to cs0, and updating the
u-boot specific tree to utilize the new flash node value.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Starting with commit 92f1e9a4b3 ("clk: Detect failure to set
defaults") the clk driver for the PX30 would fail to probe for the
Odroid Go Advance. This patch is to remove the clock for the GPU from
the U-Boot specific devicetree, as that clock is not supported by the
U-Boot clk_px30 driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFlfXAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyHzuB/4pV2iAeFBjNf6YYsuk
uvBQm7+j+AQzy0J337bDwulvw8wTKKlaid4qfOpEjW316DI9oXN1bXTlwNsjtQvO
zTILW7MoBjDRhZHsSkeSfIuD+Sc80juAoLBv+GXskQdZOTQUbWdmi2o60gdY5Ba4
WN0i4zOGVqd7xoDuDgM3XC1M2RnKerxDeVt20Ji+5dFfmes11m7br6sWj2j/45f+
q3G1ufHl+ea+8oRLZGjn2ddKCb1wLLOrNZA+74dsZ5SN0LCN0vFsE3+JAk4RZ2A5
omiHVApjE+J3vAjwiVY7apjcIdVEeyb5AioiXSBAEZiq1l1UI7eKDQT75bDkaKSs
4wBV
=78ME
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.01 cycle:
This small feature set adds the support for PWM driver for the sama5d2
SoC. It also adds a node in the DT for this SoC.
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
This fixes the usage of the USB 3.0-capable port under U-Boot as USB
2.0-only port.
Original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Account for the changes done between merge proposal and the final merge.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).
Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).
Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Current CP1 pinctrl that is set on the Puzzle M801 is incorrect.
CP1 pins are only used for the SMI bus and the MSS I2C, all other
pins are just GPIO-s.
Due to this being set completely wrong, the pinctrl was actually
ended up being hardcoded in the board_early_init_f() step so that
SMI would work.
That is obviously not the right thing to do, so convert the register
hex values that were being written to individual pin modes and set it
in the DTS.
Add the SMI pins to the CP1 MDIO node as otherwise CP1 pinctrl does
not get probed without an consumer.
Fixes: 2ae2b8a2 ("arm: mvebu: Initial iEi Puzzle-M801 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB
to 127 MiB") increased size of PCIe MEM to 127 MiB, which is the maximal
possible size for allocated 128 MiB PCIe window. PCIe IO size in that
commit was unchanged.
Armada 3720 PCIe controller supports 32-bit IO space mapping so it is
possible to assign more than 64 KiB if address space for IO.
Currently controller has assigned 127 MiB + 64 KiB memory and therefore
there is 960 KiB of unused memory. So assign it to IO space by increasing
IO window from 64 KiB to 1 MiB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB to 127 MiB")
Reviewed-by: Stefan Roese <sr@denx.de>
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common imx8mm-venice-u-boot.dtsi (dtb for the
'DEFAULT_DEVICE_TREE) so that it inherits things like binman.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Synchronize the u-boot and kernel imx device trees, using tuned
script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus")
Per devicetree specification, generic names are recommended to be
used, such as bus.
i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node
name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add u-boot.dtsi specific to imx6-apalis with a watchdog enabled.
If OP-TEE is loaded by SPL, it may use a watchdog to handle fails of
u-boot running. Enable the watchdog in SPL to use it by OP-TEE.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since c6df0e2ffd ("net: phy: micrel: add support for DLL setup on ksz9131")
the Micrel PHY driver correctly configures the delay register. The Verdin PHY
is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
After the enforcement of DM_MMC the microSD card is not detected. Fix by
correctly configuring the card detect in the devicetree.
Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
Import the initial dts queued for Linux 5.16.y
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Alpha sort the Amlogic dtb list (same as the kernel).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since Linux commmit [1], the order is fixed with aliases, in order to keep the
MMC device order, set it back to HW order in U-Boot dtsi files.
[1] ab547c4fb39f ("arm64: dts: amlogic: Assign a fixed index to mmc devices")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This allows to use the watchdog in custom scripts but does not enforce
that the OS has to support it as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Prepares for the addition of the IOT2050 board which is based on the TI
AM65x. The board comes in four variants, Basic and Advanced, each as
product generation 1 (SR1.0) and 2 (SR2.x), so there are separate dts
files needed. Furthermore, the SPL has its own device tree.
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The WDT devices described in the general .dtsi file
should be marked as "disabled" by default.
A WDT should be then enabled in the board specific
.dts file on demands.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release. Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.
Tested on j721e_evm and am65x_evm.
Signed-off-by: Tom Rini <trini@konsulko.com>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
During the migration to a single DTSI for the CP110-s specific pinctrl
compatibles were moved to the SoC DTSI as CP0 and CP1 have some specifics.
Namely, CP0 eMMC/SDIO support depends on the mvebu-pinctrl driver setting
the BIT(0) in eMMC PHY IO Control 0 Register to 0 in order for the connect
the eMMC/SDIO PHY to the controller and not use it as a MPP pin multiplexor.
So, the mvebu-pinctrl driver check specifically for the
"marvell,armada-8k-cpm-pinctrl" compatible to clear the that bit.
Issue is that compatibles in the 8040 DTSI were set to "marvell,8k-cpm-pinctrl"
for CP0 and "marvell,8k-cps-pinctrl" for the CP1.
This is obviously incorrect as the pinctrl driver does not know about these.
So fix the regression by applying correct compatibles to the DTSI.
Regression found and tested on the Puzzle M801 board.
Fixes: a0ba97e5 ("arm: armada: dts: Use a single dtsi for cp110 die description")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 0d52bab46 (mx7dsabre: Enable DM_ETH) changed these flags from 0
(aka GPIO_ACTIVE_HIGH) to GPIO_ACTIVE_LOW. It claimed to "Also sync
device tree with v5.5-rc1", but in the linux tree, these gpios have
always been GPIO_ACTIVE_HIGH ever since this node was introduced
around v4.13 (linux commit 184f39b5).
I'm guessing that the reason for the GPIO_ACTIVE_LOW was to work
around the behaviour of the soft-spi driver back then, which
effectively defaulted to spi-mode 3 and not 0. That was arguably a bug
in the soft-spi driver, which then got fixed in 0e146993bb (spi: add
support for all spi modes with soft spi), but that commit then broke
ethernet on this board.
Fix it by setting the gpios as active high, which as a bonus actually
brings us in sync with the .dts in the linux source tree.
Without this, one gets
Net: Could not get PHY for FEC0: addr 0
No ethernet found.
With this, ethernet (at least ping and tftp) works as expected from
the U-Boot shell.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joris Offouga <offougajoris@gmail.com>
Cc: "Christian Bräuner Sørensen" <yocto@bsorensen.net>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The WDT on this system should be enabled, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
The USB peripheral controller is the DWC2 controller 1, not 0.
Update the phandle to fix UDC support on this board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The WDT on this system should be enabled, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Continue to use the "ssbl" name for GPT partition of secondary boot
stage = U-Boot for basic boot with SPL to avoid to disturb existing user.
The "fip" partition name is only used for TFA_BOOT with FIP, it is a TF-A
BL2 requirement; it the default configuration for STMicroelectronics
boards.
Fixes: b73e8bf453 ("arm: stm32mp: add defconfig for trusted boot with FIP")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace the number in the flexcom-mode property with the define from the
include file.
This corresponds to the approach in Linux kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixed the following DTC build warning (reproducible with W=1)
arch/arm/dts/at91-sama5d2_icp.dtb: Warning (unit_address_format): /ahb/ohci@00400000: unit name should not have leading 0s
arch/arm/dts/at91-sama5d2_icp.dtb: Warning (unit_address_format): /ahb/ehci@00500000: unit name should not have leading 0s
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Reorder the nodes following the kernel rules: nodes in a range are sorted
by ascending bus address, and when referenced by phandle, are ordered
alphabetically.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for sst26vf064b 64Mbit qspi-flash that is
present on sama5d2_icp board.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: move u-boot properties to sama5d2_icp-u-boot.dtsi]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
sama5d2_xplained DRAM detection code will be modified to use device tree
instead of hardcoded addresses. In order to prepare that, add the memory
node to at91-sama5d2_xplained.dts.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Add bindings for CPU. This will allow displaying correctly the crystal,
CPU and master clock.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with
CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
At present SMBIOS tables are empty, which breaks some use-cases that
rely on that. Add some minimal information to fulfill this.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In the cdns3 usb driver, the clock name looked for is ref. Therefore, fix
the clock-names property in usb0 instance for proper initialization of
cdns3 usb gadget driver.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
As per Device Tree Specification [1], the status parameter of nodes can
be "okay", "disabled", etc. "ok" is not a valid parameter.
U-boot Driver Model does not recognize status="ok" either and treats
the node as disabled.
[1] https://github.com/devicetree-org/devicetree-specification/releases/tag/v0.3
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Add u-boot,dm-spl tag in the pinmux device tree node, required for MMCSD1
subsystem.
Fixes: b6059ddc45 ("arm: dts: k3-am642: Add r5 specific dt support")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
USB nodes were mistakenly disabled in
commit 942853dd96 ("arm: dts: Resync BeagleBone device trees")
This commit is to fix the following issue:
starting USB...
No working controllers found
USB is stopped. Please issue 'usb start' first.
starting USB...
No working controllers found
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=0782e8572ce43f521ed6ff15e4a7ab9aa5acdc85
Fixes: 942853dd96 ("arm: dts: Resync BeagleBone device trees")
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Paul Barker <paul.barker@sancloud.com>
Since mvpp2 is using the new mdio driver and the cp110 has been
synced with the linux upstream, the mdio has to enabled in the
device tree file.
This is missing for some device tree files and therefore the
network cards do not come online.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Make use of the new drivers for ARM U8500 introduced in the U-Boot
2021.10 merge window by adding basic support for USB Fastboot with
the "stemmy" board. As a first step this will always boot directly
into USB Fastboot for now with the console displayed on the screen
to make that obvious.
Samsung uses quite strange GPT partition labels on these boards,
so also add a bunch of fastboot_partition_alias_* to make this more
easy to use.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
So far there is no need for a clock driver in U-Boot because the
previous boot stage leaves all the necessary clocks on. However,
some drivers in U-Boot (e.g. arm_pl180_mmci) depend on having a clock
driver to obtain the clock frequency.
Setting up the clock drivers properly is a bit tricky on U8500,
so for now add a simple fixed-clock for the eMMC that allows obtaining
the clock frequency. This should be replaced eventually if some board
actually requires enabling some of the clocks.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Update ste-dbx5x0.dtsi, ste-ab8500.dtsi and ste-ab8505.dtsi with
the changes made in upstream Linux. They are taken from
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik.git/
branch "ux500-dts-for-v5.15" (pending merge for Linux 5.15).
The only relevant change for U-Boot here is
"ARM: dts: ux500: ab8500: Link USB PHY to USB controller node" [1]
which links the USB PHY to the USB controller. This is necessary on
U-Boot because the PHY driver is implemented as part of the generic
PHY subsystem that makes use of these bindings.
[1]: https://lore.kernel.org/linux-arm-kernel/20210709182234.47232-1-stephan@gerhold.net/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
U-Boot support board detection at run time and based on it change DT.
This feature is implemented for SOM Kria platforms which contain two
eeproms which contain information about SOM module and CC (Carrier card).
Full U-Boot starts with minimal DT file defined by
CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image.
It is using default setup of board_name variable initializaed to
DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option.
When DTB_RESELECT is enabled board_detection() is called. Keep it your mind
that this code is called before relocation. board_detection() is calling
xilinx_read_eeprom() which fills board_info (xilinx_board_description)
structure which are parsed in board_name_decode().
Based on DT configuration and amount of nvmemX aliases name of the board is
composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev"
<board_revision> "-" <cc_name> "-rev" <cc_revision>.
If CC is not present or more are available it keeps going.
When board name is composed and returned from board_name_decode() it is
assigned to board_name variable which is used by
board_fit_config_name_match() which is called via fdtdec_setup() when it
goes over config options in multi dtb FIT image.
From practical point of view multi DTB image is key point here which has to
contain configs for detected combinations. Unfortunately as of now they
have to be full DTBs and DTBOs are not supported.
That's why configuration like:
config_X {
description = "zynqmp-board-cc";
fdt = "board", "cc";
};
needs to be squashed together with:
fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \
arch/arm/dts/zynqmp-cc.dtbo
and only one dtb is in fit:
config_X {
description = "zynqmp-board-cc";
fdt = "board-cc";
};
For creating multi DTBs fit image use mkimage -E, e.g.:
mkimage -E -f all.its all.dtb
When DTB_RESELECT is enabled xilinx_read_eeprom() is called before
relocation and it uses calloc for getting a buffer. Because this is dynamic
memory it is not relocated that's why xilinx_read_eeprom() is called again
as the part of board_init(). This second read with calloc buffer placed in
proper position board_late_init_xilinx() can setup u-boot variables as
before.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Start of DTB should be 64bit aligned that's why also make sure that end is
also 64bit aligned. It is not required but it is nice thing to do.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace 'io-standard' property with 'power-source' property in all
zynq dts files to be in sync with Zynq Pinctrl driver.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add device tree for N5X.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <lftan.linux@gmail.com>
There is a QSPI NOR flash part on the board. Because this chip isn't
yet supported in Linux, but it is supported in U-Boot, and the
face that the RPC_SPI compatible names are different in U-Boot and
Linux, the device tree updates are confined to -u-boot.dtsi files.
In order to use the QSPI, TF-A must leave RPC unlocked by compiling
TF-A with RZG_RPC_HYPERFLASH_LOCKED=0.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Biju Bas <biju.das.jz@bp.renesas.com>
